WenmarOpen by Wenmar Pro

Service bulletins for the 2019 Ford Ecosport

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

69 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
SSM 497952021-06-01. Service bulletin. COMMUNICATION:MANUFACTURER TELEMATICS; ELECTRICAL SYSTEM. Some 2018-2021 Ford and Lincoln vehicles may not be able to perform remote commands via the FordPass/LincolnWay App due to an erroneous deep sleep message. If the vehicle has been driven within 14 days and the battery state of charge is above 9.5 volts when the deep sleep message set, this is an erroneous message. Starting and running the vehicle will clear the message and allow the remote commands to function again. Inform customers that engineering is currently working on a solution for this condition that will be released via an over the air (OTA) update that is expected in June 2021. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM) will not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
SSM 497262021-05-03. Service bulletin. ENGINE AND ENGINE COOLING. Some 2016-2018 Focus and 2018-2019 EcoSport vehicles equipped with a 1.0L EcoBoost engine, 6F15 automatic transmission and built on or before 3-Jul-2019, may exhibit an illuminated oil pressure warning lamp with a loss of engine oil pressure. This may be due to a failed engine oil pump belt tensioner which leads to a loss of engine oil pressure. If engine oil pressure at idle is below 10 psi and/or metal contamination is present in the engine oil, no further diagnostics should be performed. Replace the engine assembly to correct this condition.
SSM 496902021-03-31. Service bulletin. ELECTRICAL SYSTEM. For 2018-2021 EcoSport/Expedition/Navigator, 2019-2021 Ranger/Transit Connect, 2020-2021 Escape/Explorer/SuperDuty/Transit/Aviator/Corsair, 2021 Bronco Sport/F-150/Mustang/Mach-E the Workshop Manual (WSM) diagnostics may direct to replace a module on vehicles that use Ford Diagnosis and Repair System (FDRS). First, an FDRS session must be created on the vehicle prior to removing the faulted module. Once the session is started, run the Programmable Module Installation and replace the module only when instructed by FDRS. Installing a new module prior to starting a scan tool session may result in incomplete module configuration with DTCs U2100, U2101 and/or U2200. Once a session has been started, continue to follow normal WSM procedures to repair the vehicle.
SSM 495412021-03-03. Service bulletin. EQUIPMENT. Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code on the PTS website (Detailed Vehicle Specifications). If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early March. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early March. Monitor OASIS for updates.
TSB 20-24192021-01-05. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; POWER TRAIN. Some 2018-2020 EcoSport vehicles equipped with a 1.0L EcoBoost engine may exhibit a reoccurring illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04DB. This may be due to the software in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM.
TSB 20-23632020-11-05. Service bulletin. ELECTRICAL SYSTEM. Some 2019 MKZ, 2019-2020 EcoSport/Mustang/Continental/Fusion/F-150/Transit Connect/Ranger/Edge/Nautilus and 2020 Escape/Corsair/Aviator/Explorer/Expedition/Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
SSM 492842020-11-04. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ELECTRICAL SYSTEM:SOFTWARE. Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code. If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.
SSM 492002020-10-06. Service bulletin. ENGINE AND ENGINE COOLING. Some 2018-2019 EcoSport vehicles equipped with a 1.0L EcoBoost with an engine build date on or before 3-Apr-2019 and a 6F15 automatic transmission may exhibit an illuminated oil pressure warning lamp with a loss of engine oil pressure. This may be due to an engine oil pump belt tensioner which leads to a loss of engine oil pressure. Due to the nature of this failure, an engine replacement may be required. Engines built after 3-Apr-2019 should not be affected.
SSM 491522020-10-06. Service bulletin. EQUIPMENT; LATCHES/LOCKS/LINKAGES; ELECTRICAL SYSTEM:BODY CONTROL MODULE:SOFTWARE. Some 2018-2019 EcoSport vehicles built on or before 01-Jul-2019 may have the auto lock feature disabled. To enable this feature, use the FDRS scan tool and reprogram the body control module (BCM). For claiming, use causal part 15604 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 490842020-09-04. Service bulletin. ELECTRICAL SYSTEM. Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app , incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 20-22552020-09-02. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F150/Focus/CMAX/Edge/Fiesta/MKX/ Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
SSM 489082020-07-07. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Some 2016-2020 Ford and Lincoln vehicles equipped with a SYNC 3 Touchscreen may experience the volume control unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.
TSB 20-21712020-06-05. Service bulletin. STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS; SEATS. Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 488582020-06-04. Service bulletin. ELECTRICAL SYSTEM. Some 2012-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit an inoperative remote start with a 'Vehicle Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.
SSM 488092020-06-04. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2018-2020 Ecosport vehicles may exhibit the HVAC module being unable to communicate with the FDRS Diagnostic Scan Tool. This is caused by an issue with the FDRS tool. Do not replace the HVAC module only because it will not communicate with the FDRS Diagnostic Scan Tool.
SSM 486192020-04-02. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM. SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.
SSM 485582020-03-03. Service bulletin. ELECTRICAL SYSTEM. SSM 48558 - 2017-2020 Various Vehicles Equipped With Telematics Control Unit (TCU) - Various FordPass/LincolnWay Mobile App Concerns Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 484232020-01-08. Service bulletin. POWER TRAIN. Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 483402019-12-05. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2019 vehicles equipped with SYNC 3 may experience a map displayed on the left half of the SYNC screen with no other information/soft buttons present after updating to the latest version of V3.0 software. This issue occurs when the SYNC 3 system has been previously modified using an aftermarket device to display the Ford GT welcome screen/HMI Theme. To correct this issue, please contact the Technical Hotline Assistance Center to have the vehicle restored back to its original state.
SSM 483162019-12-05. Service bulletin. ELECTRICAL SYSTEM. Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
SSM 482672019-11-05. Service bulletin. ELECTRICAL SYSTEM. Some 2018-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
SSM 482602019-11-05. Service bulletin. ELECTRICAL SYSTEM. Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
SSM 481352019-09-09. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
SSM 481302019-09-06. Service bulletin. VISIBILITY:GLASS, SIDE/REAR; VISIBILITY. Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.
SSM 480932019-08-07. Service bulletin. ENGINE AND ENGINE COOLING. Some 2018-2019 EcoSport vehicles equipped with a 1.0L EcoBoost engine and a 6F15 automatic transmission and built on or before 3-Apr-2019 may exhibit a loss of engine oil pressure with an illuminated oil pressure warning lamp. This may be due to a broken/failed engine oil pump belt tensioner which leads to a loss of engine oil pressure. Due to the nature of this failure, an engine replacement may be required. Engines built after 3-Apr-2019 should not be affected. All tensioners built with a manufacture date on or after 23-Jan-2019 are good to use.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.