WenmarOpen by Wenmar Pro

Service bulletins for the 2012 Ford E-450

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

19 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
TSB1600572021-12-20. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Torqshift Transmission - Malfunction indicator lamp (MIL) diagnostic trouble codes (DTCS) P0751, P0730 and/or P2700
16-00572020-12-07. Service bulletin. POWER TRAIN. Some 2009-2016 E-Series, F-Super Duty, 2009-2015 F-53 Motorhome and 2011-2015 F-59 Stripped Chassis vehicles equipped with a TorqShift® transmission and a transmission built on or before 12/15/2015 may exhibit a MIL with DTCs P0751, P0730 and/or P2700
SSM 479762019-06-07. Service bulletin. POWER TRAIN. On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
SSM 469002018-01-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
15-01162015-08-20. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). FORD 2011-2016 F-250,350,450,550: SOME VEHICLES MAY EXPERIENCE MULTIPLE DIAGNOSTIC CODES STORED IN THE POWER CONTROL MODULE MEMORY DUE TO CRYSTALS DEVELOPING ON THE INJECTOR NOZZLE. *LJ
ASI-445342014-10-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. FORD: WHEN SHIFTING BETWEEN PARK, REVERSE AND/OR DURING 2-3 SHIFT, AN INTERMITTENT CLUNK OCCURS WITH A TORQSHIFT TRANSMISSION. MODEL 2003-2014 F-SUPER DUTY, E SERIES, EXCURSION, F-53 MOTORHOME CHASSIS, LOW CAB FORWARD. *PE
ASI-445382014-10-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. FORD/LINCOLN/MERCURY: THE INDICATOR MAY ILLUMINATE OVERDRIVE OFF AND/OR SLIPPING IN 3RD OR NO 4TH GEAR, DUE TO DIRECT CLUTCH FAILURE AND DIAGNOSTIC TROUBLE CODE (DTC) P0733 AND/OR P0734. MODEL 2008-2013 MARK LT, F-150, CROWN VICTORIA, GRAND MARQUIS, TOWN CAR, E SERIES. *PE

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.