Service bulletin 16-0057

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10183758
Published by NHTSA	2020-12-07
Manufacturer's number	16-0057
Manufacturer's date	2016-04-05
NHTSA component	POWER TRAIN

NHTSA's summary

Some 2009-2016 E-Series, F-Super Duty, 2009-2015 F-53 Motorhome and 2011-2015 F-59 Stripped Chassis vehicles equipped with a TorqShift® transmission and a transmission built on or before 12/15/2015 may exhibit a MIL with DTCs P0751, P0730 and/or P2700

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Transmission and driveline

Trouble codes named

P0730, P0751, P2700

Vehicles listed
FORD E-150	2009, 2010, 2011, 2012, 2013, 2014
FORD E-150	2015 to 2016
FORD E-250	2009, 2010, 2011, 2012, 2013, 2014
FORD E-250	2016
FORD E-350	2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016
FORD E-450	2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016
FORD E-550	2009
FORD F-53	2009
FORD F-53	2011 to 2015
FORD F-59	2011 to 2015
FORD SUPER DUTY	2009 to 2010
MOBILITY SPECIALISTS FORD E-250	2015

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
SSM 52314	2024-03-20. Service bulletin. During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
SSM 51854	2023-09-04. Service bulletin. Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS > Diagnostics tab > HVBoM > Features > Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
SSM 51849	2023-09-01. Service bulletin. Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
TSB160057	2021-12-20. Service bulletin. Torqshift Transmission - Malfunction indicator lamp (MIL) diagnostic trouble codes (DTCS) P0751, P0730 and/or P2700
TSB160032	2021-12-20. Service bulletin. 4R75E Transmission - Grinding/Whine/Vibration/Gear Slippage - Serrvice Kit available
SSM 47976	2019-06-07. Service bulletin. On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
SSM 47823	2019-04-01. Service bulletin. Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
SSM 46900	2018-01-29. Service bulletin. Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
SSM 46451	2017-05-17. Service bulletin. 2009-2017 VEHICLES EQUIPPED WITH A 6R80, 6R100, 6R140 AUTOMATIC TRANSMISSION HAVE AN UPDATED MAIN CONTROL VALVE BODY OVERHAUL PROCEDURE. REFER TO WORKSHOP MANUAL (WSM), SECTION 307-01 FOR MAIN CONTROL VALVE BODY (7A100) OVERHAUL PROCEDURES. NOT ALL VALVE BODIES REQUIRE REPLACEMENT. INSPECT THE VALVE BODY BORES, SPRINGS AND VALVES AS DIRECTED DURING DIAGNOSIS AND REPAIR. REFER TO GENERAL SERVICE BULLETIN (GSB) G0000093 AUTOMATIC TRANSMISSION MAIN CONTROL INSPECTION FOR A VIDEO CLIP TO AID IN THE DIAGNOSIS OF THESE REPAIRS.
TSB 16-0168	2017-03-10. Service bulletin. SOME 2016-2017 E-SERIES 350/450 VEHICLES EQUIPPED WITHOUT A TRACTION CONTROL SWITCH AND BUILT ON OR BEFORE 17-FEB-2016 MAY HAVE TRACTION CONTROL FUNCTION OR TRACTION CONTROL RELATED SYMPTOMS. VEHICLES WITHOUT A TRACTION CONTROL SWITCH ARE NOT INTENDED TO HAVE TRACTION CONTROL. REPROGRAM THE POWERTRAIN CONTROL MODULE (PCM) TO THE LATEST CALIBRATION USING IDS RELEASE 103.01 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM.