Service bulletins for the 2012 Dodge Ram
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
378 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Electrical system are shown. Show all
| 30657 | 2018-06-11. Service bulletin. ELECTRICAL SYSTEM. R4801865AC Alternator Assy - 220 Amp You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of part number R4801865AC. Replacement is part number 04801865AE which is in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 04 April, 2017. |
|---|---|
| 18-050-14 REV. A | 2018-06-11. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: Drone or Vibration Present During MDS Operation This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. New PCM software is being released to address a customer's concern of a drone or vibration type condition while driving at highway speeds during MDS (Multiple Displacement System) operation.In addition, the following powertrain system improvements/enhancements are also included in this software release: Improved Electronic Voltage Regulator control to more precisely maintain system voltage. Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. (Only applies to vehicles using a block heater in ambient temperatures greater than -20°F(-29°C)). |
| 25-002-14 | 2018-06-11. Service bulletin. FUEL SYSTEM, GASOLINE; BACK OVER PREVENTION; ELECTRICAL SYSTEM; EXTERIOR LIGHTING; POWER TRAIN. Malfunction Indicator Lamp Illumination Due To Oxygen Sensor This bulletin involves the installation of an Oxygen (O2) Sensor Overlay Harness for any Oxygen Sensor related DTC(s). The Overlay Harness will consist of twelve 18 AWG wires (six from each Oxygen Sensor) that run to a new Oxygen Sensor Module connector. Four wires will be removed from the original vehicle O2 Module connector and installed in the new overlay harness O2 Module connector.Do NOT replace any parts prior to performing this bulletin and the Verifications test below. If the vehicle has any of the following DTC?s for O2 Sensors, Stored, Pending or Active, perform the Repair Procedure. P013A O2 Sensor 1/2 Slow Response - Rich To Lean (Soot related code, see note). P013B O2 Sensor 1/2 Slow Response - Lean To Rich (Soot related code, see note). P014C O2 Sensor 1/1 Slow Response - Rich To Lean (Soot related code, see note)P014D O2 Sensor 1/1 Slow Response - Lean To Rich (Soot related code, see note) P0030 O2 Sensor 1/1 Heater Circuit P0031 O2 Sensor 1/1 Heater Circuit Low P0032 O2 Sensor 1/1 Heater Circuit High P0036 O2 Sensor 1/2 Heater Circuit Malfunction P0037 O2 Sensor Heater Circuit Low 1/2 P0038 O2 Sensor Heater Circuit High 1/2 P0053 O2 Sensor Heater 1/1 Resistance P0054 O2 Sensor Heater 1/2 Resistance P064D Internal Control Module 02 Sensors Processor Performance - Bank 1 P0131 1/1 02 Sensor Shorted To Ground P0132 1/1 02 Sensor Shorted To Voltage P0135 O2 Sensor 1/1 Heater Performance P0137 1/2 02 Sensor Shorted To Ground P0138 1/2 02 Sensor Shorted To Voltage P0141 O2 Sensor 1/2 Heater Performance P113C O2 Sensor Power Supply Circuit Performance P2195 O2 Sensor 1/1 Out Of Range High P2196 O2 Sensor 1/1 Out Of Range Low P22AB O2 Sensor Positive Current Control Circuit/Open - Bank 1 Sensor 2 P22AE O2 Sensor Reference Voltage Circuit/Open - Bank 1 Sensor 2 P22B2 O2 Sensor Negative Current Control Circuit/Open - Bank 1 P22B5 O2 Sensor 1/2 Pump Cel |
| 9002503 | 2018-06-11. Service bulletin. EQUIPMENT; POWER TRAIN; BACK OVER PREVENTION; VISIBILITY; SUSPENSION; ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE. Part Description: RHR Radio Issue Description: Issue 1: While performing RHR radio reflash (software update), on rare occasions, the flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality (examples may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the following:~ 1. Power on radio~2. Press MENU H/K~3. Press System Setup S/K~4. Press Manage HDD S/K~5. Press Display Available Space on HDD S/K~6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes~ Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. ~ Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect |
| 9002688 | 2018-06-04. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM:WIRING; ENGINE AND ENGINE COOLING. 68069384A$, R8069384A$, 68086182A$, R8027067A$, RL002012A$ - Gasket, Cylinder Head Cover Before replacing injectors for Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, and/or P0206, please make sure that the wiring loom and/or connector in the valve cover gasket is not the root cause to your concern. In addition, make sure that the wiring attaching nuts are torqued to their proper value.~ |
| 18-009-13 | 2018-06-04. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Flash: MIL Illumination P1004 - Short Runner Valve Control Performance This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P1004 - Short Runner Valve Control Performance |
| 68184926A$ | 2018-05-21. Service bulletin. ELECTRICAL SYSTEM. Integrated Center Stack If vehicle is found within 50 mile radius of the Detroit Metro area please hold vehicle and contact:~ Contact one of the following:~ Daniel Acciacca CELL (586) 709-1537~ Michael Savich CELL (248) 214-7270~ Ayed Hadaad CELL (248) 941-8707~ Issue: On a 2015 & 2016MY LA (Challenger), LD(Charger) and LX (300), the Integrated Center Stack (ICS) may experience a lock-up/Inop condition (complete loss of functionality) during any vehicle diagnostic session (reading fault codes, clearing fault codes, reflashing of any module, etc.). If this occurs, do not replace the ICS. The module functionality can be restored if it is reset by disconnecting power to it (by removing fuse, battery disconnect or module connector disconnect).~ |
| 05091960A$ | 2018-05-21. Service bulletin. ELECTRICAL SYSTEM. Hands Free Module - CTM ? Peiker For RT, JK and MK bodies only; Before replacing the Hands Free Module (HFM), please contact Gaurav Saxena at cell (248) 260-0583~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair. |
| 05066241A$ | 2018-05-21. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Battery - Transmitter For vehicles within 12 Months in Service which have a "FOB Battery Low" message within Cluster or DTC B1A10 or B1A11 Active or Stored. Engineering is requesting complete FOB returned unopened (ie, battery not removed or FOB housing opened!). ~ All others, follow normal procedures.~ Please ensure Dealer Technicians are aware of this request to allow for gain in FOB Battery depletion understanding. |
| 18-012-14 | 2018-05-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Flash: Malfunction Indicator Lamp (MIL) Illumination. Includes Various Driveability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: ? P0300 - Multiple Cylinder Misfire NOTE: The P0300 improvement only applies to vehicles using a block heater in ambient temperatures greater than -20°F(-29°C). ? P2008 - Short Runner Valve (SRV) Control Circuit ? P1004 - Short Runner Valve Control Performance ? P2016 - Intake Manifold Runner Position Sensor Circuit Low ? P2017 - Intake Manifold Runner Position Sensor Circuit High ? P0456 - Evap System Small Leak Customers may also experience any of the following conditions (applies only to vehicles equipped with a CNG engine): ? Excess gasoline mode operation under normal operating conditions (switching to gasoline mode too often) ? Slight hesitation on initial acceleration when starting in gasoline mode ? Engine speed fluctuation on first gasoline to CNG mode transition under extremely low ambient temps |
| 9002350 | 2018-05-21. Service bulletin. TRAILER HITCHES; ELECTRICAL SYSTEM. Part Description: Integrated Trailer Brake Module Issue Description: Before replacing an Integrated Trailer Brake Module (ITBM) please review the following items.~ 1. The ITBM does not control the trailer lights. If the trailer lights are not working, do not change the ITBM.~ 2. If the Diagnostic Trouble Code(DTC) reported by the ITBM is C10C7-11 "Electronic Trailer Brake Control Output Short to Ground" or C10C7-12 "Electronic Trailer Brake Control Output Short to Battery", please verify the wiring on the trailer. The purpose of this faults is to protect the ITBM output from faulty trailer wiring.~ 3. If the customer complaint is ITBM not detecting the trailer connection. Do not change the ITBM until the system has been verified with load simulation and confirmed that ITBM is not recognizing the load. If load simulation indicates that the ITBM is operating properly, please verify the trailer wiring.~ 4. ITBM output will not be available if a trailer is not connect and plugged into the vehicle. The ITBM must detect a trailer before you will get trailer brake output.~ 5. Please follow the service manual procedures before changing the ITBM.~ This part can only be used as a replacement on vehicles with the Integrated Trailer Brake system already installed. Do not attempt to use this module for the purpose of adding the Integrated Trailer Brake system to a vehicle that was not originally equipped. You will encounter configuration difficulties. MOPAR has developed a kit, part number 82212548 to be used for installation of the Integrated Trailer Brake system on vehicles. |
| 25-004-12 | 2018-05-14. Service bulletin. ELECTRICAL SYSTEM. Malfunction Indicator Lamp Illumination Due To Oxygen Sensor This bulletin involves replacement of the Oxygen Sensor Connectors for any Oxygen Sensor related DTC. Do NOT replace any parts prior to performing this bulletin and the Verifications test below. If the vehicle has any of the following DTC?s for O2 Sensors, Stored, Pending or Active, perform the Repair Procedure. ? P013A O2 Sensor 1/2 Slow Response - Rich To Lean (Soot related code, see note) ? P013B O2 Sensor 1/2 Slow Response - Lean To Rich (Soot related code, see note) ? P014C O2 Sensor 1/1 Slow Response - Rich To Lean (Soot related code, see note) ? P014D O2 Sensor 1/1 Slow Response - Lean To Rich (Soot related code, see note) ? P0030 O2 Sensor 1/1 Heater Circuit ? P0031 O2 Sensor 1/1 Heater Circuit Low ? P0032 O2 Sensor 1/1 Heater Circuit High ? P0036 O2 Sensor 1/2 Heater Circuit Malfunction ? P0037 O2 Sensor Heater Circuit Low 1/2 ? P0038 O2 Sensor Heater Circuit High 1/2 ? P0053 O2 Sensor Heater 1/1 Resistance ? P0054 O2 Sensor Heater 1/2 Resistance ? P064D Internal Control Module 02 Sensors Processor Performance - Bank 1 ? P0131 1/1 02 Sensor Shorted To Ground ? P0132 1/1 02 Sensor Shorted To Voltage ? P0135 O2 Sensor 1/1 Heater Performance ? P0137 1/2 02 Sensor Shorted To Ground ? P0138 1/2 02 Sensor Shorted To Voltage ? P0141 O2 Sensor 1/2 Heater Performance ? P113C O2 Sensor Power Supply Circuit Performance ? P2195 O2 Sensor 1/1 Out Of Range High ? P2196 O2 Sensor 1/1 Out Of Range Low ? P22AB O2 Sensor Positive Current Control Circuit/Open - Bank 1 Sensor 2 ? P22AE O2 Sensor Reference Voltage Circuit/Open - Bank 1 Sensor 2 ? P22B2 O2 Sensor Negative Current Control Circuit/Open - Bank 1 ? P22B5 O2 Sensor 1/2 Pump Cell Current Trim Circuit Open ? P2237 O2 Sensor 1/1 Pump Cell Current Circuit Low ? P2243 O2 Sensor 1/1 Reference Voltage Circuit Open ? P2251 O2 Sensor 1/1 Negative Current Control Circuit/Open ? P2270 O2 Sensor 1/2 Out Of R |
| 18-012-13 | 2018-05-14. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE); FUEL SYSTEM, GASOLINE; FUEL SYSTEM, DIESEL; ELECTRICAL SYSTEM:SOFTWARE. FLASH: Diagnostic and System Enhancements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM) with new software. Cab chassis trucks equipped with a 6.7L Cummins diesel have a number of software improvements available. This latest Service Bulletin (SB) will include:Improvements To Prevent Unnecessary Malfunction Indicator Lamp (MIL) Illumination For: P061A - ETC LEVEL 2 TORQUE PERFORMANCE P229F - AFTERTREATMENT NOx SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 P2453 - DIESEL PARTICULATE FILTER PRESSURE SENSOR A CIRCUIT PERFORMANCE P2609 - INTAKE AIR HEATER SYSTEM PERFORMANCE P1123 - POWER TAKE OFF SYSTEM MONITOR CONTROL ERROR U010E - LOST COMMUNICATION WITH DIESEL EXHAUST FLUID CONTROL UNIT U059F - INVALID DATA RECEIVED FROM NOx SENSOR "B" P20EE - SCR NOx CATALYST EFFICIENCY BELOW THRESHOLD - BANK 1; for DTC's set at highway speed and/or high load drive cycles Vehicles with DTC P20EE set in conditions other than highway speed and/or high load drive cycles should have normal diagnostics performed Enhanced Diagnostics For: Selective Catalyst Reduction (SCR) efficiency diagnostic improvements.Other Updates: Too frequent regeneration readiness improvement Correct CAC out voltage in WiTech Add ability to read EMP sensor value in WiTech Enable EMP deicing algorithm Display correct crankcase pressure in WiTech Display correct EGR position in WiTech Improve idle shutdown messages - extra message removed Display correct alternator voltage in WiTech Idle shutdown message on EVIC. Turbo protection feature (Not displayed if vehicle is in park or no vehicle speed). Limits RPM at cold ambient to prevent turbo damage. Scan tool display updates. Correct operation of remote PTO. System robustness improvements. |
| 08-053-12 | 2018-05-14. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; ELECTRICAL SYSTEM:SOFTWARE. Flash: RHR, RHW Or RHP Radio Software Enhancements This bulletin involves upgrading the software on the RHR, RHW or RHP Radio. The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements. |
| 08-021-13 | 2018-02-21. Service bulletin. ELECTRICAL SYSTEM. Flash: Hands Free Module Customer Satisfaction Enhancements This Bulletin involves performing a USB service flash of the Hands Free Module (HFM). The customer satisfaction enhancements are included with this software release:After the HFM has been updated it will receive these enhancements. Reduced ?Device Reading? wait time after connecting a device to the remote USB port. Call / Dial separation improves upon names being recognized as phone numbers. Improved sound quality during Bluetooth streaming. Increased iPod and iPhone compatibility. SMS messaging support via MAP protocol (not all phones support the MAP protocol). Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. Previous button will return the song currently being played to the beginning of the track. AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected.USB mode resume will no longer 'resume' after ignition OFF |
| 18-012-13 | 2018-02-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. FLASH: Diagnostic and System Enhancements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM) with new software. Cab chassis trucks equipped with a 6.7L Cummins diesel have a number of software improvements available. This latest Service Bulletin (SB) will include:Improvements To Prevent Unnecessary Malfunction Indicator Lamp (MIL) Illumination For: P061A - ETC LEVEL 2 TORQUE PERFORMANCE P229F - AFTERTREATMENT NOx SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 P2453 - DIESEL PARTICULATE FILTER PRESSURE SENSOR A CIRCUIT PERFORMANCE P2609 - INTAKE AIR HEATER SYSTEM PERFORMANCE P1123 - POWER TAKE OFF SYSTEM MONITOR CONTROL ERROR U010E - LOST COMMUNICATION WITH DIESEL EXHAUST FLUID CONTROL UNIT U059F - INVALID DATA RECEIVED FROM NOx SENSOR "B" P20EE - SCR NOx CATALYST EFFICIENCY BELOW THRESHOLD - BANK 1; for DTC's set at highway speed and/or high load drive cycles Vehicles with DTC P20EE set in conditions other than highway speed and/or high load drive cycles should have normal diagnostics performed Enhanced Diagnostics For: Selective Catalyst Reduction (SCR) efficiency diagnostic improvements.Other Updates: Too frequent regeneration readiness improvement Correct CAC out voltage in WiTech Add ability to read EMP sensor value in WiTech Enable EMP deicing algorithm Display correct crankcase pressure in WiTech Display correct EGR position in WiTech Improve idle shutdown messages - extra message removed Display correct alternator voltage in WiTech Idle shutdown message on EVIC. Turbo protection feature (Not displayed if vehicle is in park or no vehicle speed). Limits RPM at cold ambient to prevent turbo damage. Scan tool display updates. Correct operation of remote PTO. System robustness improvements. |
| 9002688 | 2018-02-21. Service bulletin. ELECTRICAL SYSTEM. 68069384A$, R8069384A$, 68086182A$, R8027067A$, RL002012A$ - Gasket, Cylinder Head Cover Before replacing injectors for Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, and/or P0206, please make sure that the wiring loom and/or connector in the valve cover gasket is not the root cause to your concern. In addition, make sure that the wiring attaching nuts are torqued to their proper value.~ |
| 08-065-12 | 2018-02-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. RHR Navigation Map Enhancements This bulletin involves updating the RHR radios navigation map database software. Customers may experience a condition were new roads and new point of interests are not accurately shown on their navigation system.Updating the navigation software will help address most of the map inaccurate results. |
| 25-004-12 | 2018-02-21. Service bulletin. ELECTRICAL SYSTEM. Malfunction Indicator Lamp Illumination Due To Oxygen Sensor This bulletin involves replacement of the Oxygen Sensor Connectors for any Oxygen Sensor related DTC. Do NOT replace any parts prior to performing this bulletin and the Verifications test below. If the vehicle has any of the following DTC?s for O2 Sensors, Stored, Pending or Active, perform the Repair Procedure.? P013A O2 Sensor 1/2 Slow Response - Rich To Lean (Soot related code, see note)? P013B O2 Sensor 1/2 Slow Response - Lean To Rich (Soot related code, see note) ? P014C O2 Sensor 1/1 Slow Response - Rich To Lean (Soot related code, see note) ? P014D O2 Sensor 1/1 Slow Response - Lean To Rich (Soot related code, see note) ? P0030 O2 Sensor 1/1 Heater Circuit ? P0031 O2 Sensor 1/1 Heater Circuit Low ? P0032 O2 Sensor 1/1 Heater Circuit High ? P0036 O2 Sensor 1/2 Heater Circuit Malfunction ? P0037 O2 Sensor Heater Circuit Low 1/2 ? P0038 O2 Sensor Heater Circuit High 1/2 ? P0053 O2 Sensor Heater 1/1 Resistance ? P0054 O2 Sensor Heater 1/2 Resistance ? P064D Internal Control Module 02 Sensors Processor Performance - Bank 1 ? P0131 1/1 02 Sensor Shorted To Ground ? P0132 1/1 02 Sensor Shorted To Voltage ? P0135 O2 Sensor 1/1 Heater Performance ? P0137 1/2 02 Sensor Shorted To Ground ? P0138 1/2 02 Sensor Shorted To Voltage ? P0141 O2 Sensor 1/2 Heater Performance ? P113C O2 Sensor Power Supply Circuit Performance ? P2195 O2 Sensor 1/1 Out Of Range High ? P2196 O2 Sensor 1/1 Out Of Range Low ? P22AB O2 Sensor Positive Current Control Circuit/Open - Bank 1 Sensor 2 ? P22AE O2 Sensor Reference Voltage Circuit/Open - Bank 1 Sensor 2 ? P22B2 O2 Sensor Negative Current Control Circuit/Open - Bank 1 ? P22B5 O2 Sensor 1/2 Pump Cell Current Trim Circuit Open ? P2237 O2 Sensor 1/1 Pump Cell Current Circuit Low ? P2243 O2 Sensor 1/1 Reference Voltage Circuit Open ? P2251 O2 Sensor 1/1 Negative Current Control Circuit/Open ? P2270 O2 Sensor 1/2 Out Of |
| 08-057-12 REV. A | 2018-02-21. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; ELECTRICAL SYSTEM:SOFTWARE. RBZ Or RHB Radio Software Enhancements This bulletin involves upgrading the software on the RBZ or RHB Radio. The customer may experience one or more of the following conditions. Digital photos loaded onto the hard drive intermittently get lost (RBZ & RHB). CD/DVD will not play (RHB only). Navigation accept screen will not clear (RHB only). Navigation shows ?acquiring signal? for an extended period of time (RHB only). New navigation graphics (RHB only). |
| 08-053-12 | 2018-02-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Flash: RHR, RHW Or RHP Radio Software Enhancements This bulletin involves upgrading the software on the RHR, RHW or RHP Radio. The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements. |
| 68210071A$ | 2017-11-03. Service bulletin. ENGINE; ELECTRICAL SYSTEM. Intake Grid Heater Grid Heater Relay 2012 - 2016 6.7L Cummins engines with Intake Heater issues or DTC P2609 and P0542, please replace the Intake Heater Grid and Relay as a set. 68210071A$ (relay) and 05187880A$ (grid). Inspect electrical cable between the heater grid and relay for signs of possible overheating. Replace cable as necessary. |
| 18-066-16 REV. A | 2017-11-03. Service bulletin. FUEL SYSTEM, GASOLINE; POWER TRAIN; ELECTRICAL SYSTEM. Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with updated software. Some customers may describe one or more of the following: MIL Illumination Upon further investigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set: · P2096 - Downstream Fuel Trim System 1 Lean (5.7L Engines). · P2097 - Downstream Fuel Trim System 1 Rich (5.7L Engines). · P2098 - Downstream Fuel Trim System 2 Lean (5.7L Engines). · P2099 - Downstream Fuel Trim System 2 Rich (5.7L Engines). Drivability Improvements: · MIL Lamp without DTC Active - Permanent Fault Code Issue (fix permanent fault code retention). · ASD Relay (to improve fuel pump relay initialization at key on). · Fuel pump relay operation at key on. · Engine seems to lacks power at high engine RPMs (5.7L and 4.7L Engines). · Shudder or shake condition on wide open throttle stab during downshift event (5.7L and 4.7L Engines). · EVAP Diagnostic Enhancements. This diagnostic routine will be disabled while the vehicle is in decel fuel shut off mode.(3.7L/4.7L Engines only). · Audible knock sound on WOT launches (DJ/DD 5.7L Engines only). Transmission Improvements: · High engine RPMs needed before vehicle will upshift from 3rd to 4th. (5.7L and 4.7L Engines). · Harsh 1st to 2nd gear upshift (5.7L and 4.7L Engines). · Unexpected or busy downshift while coasting between 45-48 mph (72-77 kmh) (DS 5.7L Engines only). |
| 09-010-16 REV. A | 2017-11-03. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE. Engine Surge Or Hard Start (X63 Warranty Extension) This bulletin involves replacing the Exhaust Gas Recirculation (EGR) valve, if code P0404 is set. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTC) has been set in the Powertrain Control Module (PCM): · P0404 - EGR Position Sensor Performance - (Exhaust Gas Recirculation). In addition, the customer may notice the following condition(s) due to the P0404 DTC being set: · An occasional engine surge can be felt. · Engine is hard to start at times. |
| 09-010-16 | 2017-11-03. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE. Engine Surge Or Hard Start (X63 Warranty Extension) This bulletin involves replacing the Exhaust Gas Recirculation (EGR) valve, if code P0404 is set. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTC) has been set in the Powertrain Control Module (PCM): · P0404 - EGR Position Sensor Performance - (Exhaust Gas Recirculation). In addition, the customer may notice the following condition(s) due to the P0404 DTC being set: · An occasional engine surge can be felt. · Engine is hard to start at times. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.