WenmarOpen by Wenmar Pro

Service bulletins for the 2016 Dodge Challenger

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

278 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
Z5091195A$2018-06-11. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT:ELECTRICAL. RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
18-032-162018-06-11. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Flash: Powertrain Diagnostic And System Improvements This bulletin involves reprogramming of the Powertrain Control Module (PCM) with the latest software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set: · P0335 - Crankshaft Position Sensor Circuit. · P0339 - Crankshaft Position Sensor Intermittent. · P0456 - EVAP System Small Leak.
03-004-162018-06-11. Service bulletin. POWER TRAIN. Inspect And Replace Propeller Shaft This bulletin involves inspecting and replacing the propeller shaft due to a whining noise at high speeds. SYMPTOM/CONDITION: The customer or technician may hear a whining noise coming from the rear axle area.
21-023-162018-06-11. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming of the Transmission Control Module (TCM) with the latest available software. SYMPTOM/CONDITION: Customers may experience any of the following symptoms: · Hanging or delayed upshift when braking downhill or when braking after high vehicle acceleration rate. · Releasing the accelerator pedal rapidly causes hanging or delayed upshift. **Updating the TCM software will correct the conditions listed above and also improve shift quality for a 2-1 downshift (LA vehicle).**
18-073-162018-06-11. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Flash: 3.6L Powertrain Diagnostic And System Enhancements. This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · P0335 - Crankshaft Position Sensor Circuit. · P0456 - EVAP System Small Leak. · P2610 - PCM Internal Engine Off Timer Performance. In addition to the above DTCs, this software release also includes: · Enhancements to the disable misfire monitor when P0335 is present. · Add a global disable to small leak monitor when the fuel level is above 88%. · Update small leak diagnostic to require 5 minutes of engine runtime and 120 minutes of engine off time. · Updates to prevent false failure due to wrong ambient temperature reading.
18-074-162018-06-11. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Flash: Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with updated software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · P0456 - EVAP System Small Leak. · P0335 - Crankshaft Position Sensor Circuit. · P2610 - PCM Internal Engine Off Timer Performance.
68258644A$2018-06-11. Service bulletin. ELECTRICAL SYSTEM; SERVICE BRAKES, AIR:ANTILOCK:CONTROL UNIT/MODULE. Anti-Lock Brake Module (ABS) Before replacing the ABS module, please call Fadi Korkis at cell (586) 722-4100. If you don't receive response within 15 minutes, please continue with normal repair procedure.
08-028-172018-06-11. Service bulletin. EQUIPMENT. RA3 And RA4 Radio Over The Air Software Updates This bulletin provides information regarding the latest Flash Over The Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update: Adds Apple Siri® Eyes Free capability for iPhone® owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loses time. Charge Complete notification is not received (RU PHEV only). Media devices, Phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).
90032732018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Trans Pan or Gasket If your repair requires replacing one of the two part numbers for a leak, prior to the repair please call Enzo Piazza at cell (248) 467-9163. If you cannot reach Enzo within 15 minutes proceed with the repair. Enzo needs to know the location of the leak, if the bolts were torqued, if there is sealer skip, or anything that may be pertinent to the cause of the leak. Photos would be very helpful and can be sent to Enzo's cell phone or his email. Enzo's e-mail address is enzo.piazza@fcagroup.com.
90035842018-06-11. Service bulletin. STEERING. Electric Power Steering Gear If any of the following DTCs exist, it is okay to replace the steering gear: C2217-00, C15C1-00 (EPS Mechanical Performance) or C15DB-00 (Latch Active) otherwise perform the following; 1) Electrical, Communication or DTC (other then above) issue please contact: Terry Gavit @ cell (248) 882-6108 terry.gavit@fcagroup.com Engineering is requesting a copy of Vehicle Scan Report (VSR) to be emailed to the above address. 2) Noise or Mechanical issue please contact: Ruth Delong @ cell (810) 569-0354.~ If you do not receive a return call within 15 minutes, proceed with the repair.~ Please be sure to attach a copy of the Vehicle Scan Report on the repair order
90036962018-06-11. Service bulletin. STRUCTURE:BODY:DOOR. Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
90036552018-06-11. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. Rear Axle Assembly If replacing Limited Spin Differential (LSD)/Anti-Spin Differential rear axles for any reason, the Mopar replacement axle will need the oil drained and re-filled with oil PN: 68083381AA (which contains updated friction modifier). This change was recently introduced in production to help address axle noise concerns being reported from the field while the vehicle is performing tight turning maneuvers. Failure to do so may result in a customer returning with noise complaints. NOTE: If the Mopar replacement axle serial number is past the following dates below for the corresponding axle part numbers, DO NOT DRAIN AND REFILL. The replacement axle will already have new fluid: Axle Part#: 53010668XX ? Serial # T03UG0047EXXXX Axle Part#: 53010669XX ? Serial # T03UG0047GXXXX Axle Part#: 68269917XX ? Serial # T03UG0037JXXXX Axle Part#: 05038703XX ? Serial # T03UG0047HXXXX Otherwise, perform the following repair procedure in the order given: 1. Follow standard rear axle installation procedure. Refer to the detailed service procedures available in DealerCONNECT> TechCONNECT under: Service Info> 03 - Differential and Driveline> Rear Axle> Installation>Standard Procedure>Rear Axle 2. Follow standard axle fluid drain/re-fill service procedure in TECHCONNECT. Refer to the detailed service procedures available in DealerCONNECT> TechCONNECT under: Service Info> 03 - Differential and Driveline> Rear Axle> Standard Procedure>Standard Procedure - Fluid Drain and Fill
90036942018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
90036812018-06-11. Service bulletin. SEAT BELTS. Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
90036872018-06-11. Service bulletin. SEAT BELTS. Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
68277402A2018-06-11. Service bulletin. VEHICLE SPEED CONTROL:CRUISE CONTROL. Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure
09-007-162018-06-11. Service bulletin. STRUCTURE. Tighten Generator Mounting Bolts This bulletin involves torquing the generator mounting bolts to proper specifications. The customer may hear a noise coming from the generator or possibly experience loss of charging.
RL305553A2018-06-11. Service bulletin. POWER TRAIN. 9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
5LE49LA8A2018-06-11. Service bulletin. EQUIPMENT. Console Lid LA ONLY: If you are replacing the console lid because the latch is broken, please also replace the console base in addition to the console lid. Please call Mike Wicker on cell (248) 821-9350 prior to replacing the components. If you don't receive a response within 15 minutes, please continue with normal repair procedure.
18-062-172018-06-04. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN. Flash: Powertrain Diagnostic and System Improvements This bulletin involves reprogramming of the Powertrain Control Module (PCM) with the latest software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set:U1424 - Implausible Engine Torque Signal Received. P0122 - Throttle Position Sensor 1 Circuit Low. P0123 - Throttle Position Sensor 1 Circuit High. P0222 - Throttle Position Sensor 2 Circuit Low. P0223 - Throttle Position Sensor 2 Circuit High. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. P2227 - Barometric Pressure Circuit Performance. P3032 - Barometric Pressure Sensor Performance Plausibility. P0441 - Evap Purge System Performance. P0455 - Evap System Large Leak. P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0456 - Evap System Small Leak. In addition, the following software enhancements are available:Reduction in reverse gear lockout speed from 16 kph to 5 kph (10 mph to 3 mph) to improve MTX transmission durability(Sales Code DEC only). Improvement to Intake Air Sensor (IAS) accuracy calibration(Sales Code DEC only). Changes to Enhanced Automated Oil Change Indicator (EAOCI) calibration to more accurately determine maintenance interval based on engine loads and driving habits.
23-030-172018-06-04. Service bulletin. STRUCTURE:BODY:HOOD. Hood Seal Torn or Deformed This bulletin involves replacing the hood seals due to damage and/or being torn. The customer may experience the hood seal drooping due to cracks and tears on the hood seal.
08-046-172018-06-04. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. RA3 and RA4 Radio Enhancements This bulletin involves inspecting and if required, updating the radio software. Customers may experience one or more of the following:?Navigation Failed? message is displayed. Navigation is inoperative or inaccurate. CD player will not play songs and/or locks up the radio. Clock will not automatically update to local time. Clock may be off by several hours. (RA3 Only). HVAC temperature out of sync with radio display (KL vehicles). Some Uconnect App remote commands do not execute with the vehicle. Radio Apps are inoperative. Adds Apple Siri® Eyes Free capability for iPhone® owners. Auto Play can now be configured. Radio will lock up. Radio display screen is black or blank. Battery drain - due to radio staying on. Navigation failed message is displayed. Clock not automatically updating to local time. HVAC temperature out of sync with radio display (KL vehicles). Improvements:Adds Apple Siri Eyes Free capability for iPhone owners. Add the ability to drag and drop icons into the menu bar. Enhanced Voice Recognition (VR) performance. Media devices, phone pairing, and Bluetooth usage improvements. Improved tuner performance. Enhancements in Connectivity Apps (Yelp®, Pandora®, Aha®, etc). Human Machine Interface (HMI) improvements. Adds ?do not disturb? text message feature. Satellite radio reception improvements.
90033572018-06-04. Service bulletin. ENGINE AND ENGINE COOLING. Pentastar Oil Filter Adapter All vehicles equipped with a 3.2L or 3.6L engine; If replacing the Oil Filter Adapter (OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.
90034132018-06-04. Service bulletin. VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
90031092018-06-04. Service bulletin. VISIBILITY:WINDSHIELD WIPER/WASHER. Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.