WenmarOpen by Wenmar Pro

Service bulletins for the 2018 Chrysler Pacifica

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

491 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Driver assistance are shown. Show all

Bulletins, newest first
90044522024-01-08. Service bulletin. BACK OVER PREVENTION: SENSING SYSTEM: CAMERA. CAMERA, Rear View Prior to replacement, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
18021232024-01-02. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING; BACK OVER PREVENTION; POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: Major monitor (misfire) and other diagnostics are disabled on a pending DTCs P0335 and P0339. ? **P0335 - Crankshaft Position Sensor Circuit (NA Only). ? P0339 - Crankshaft Position Sensor Intermittent (NA Only).** ? P06E4 - Control Module Wake-Up Circuit Performance. Software enhancement: Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states. ? Corrections to allow the vehicle to clear the permanent fault codes. This bulletin involves reprogramming the PCM with the latest available software. NOTE: Four modules are required to be flashed for this update to be effective, the following modules are all to be updated along with this PCM update: ? Electronic Brake Booster Module (EBBM). ? AntiLock Brake System Module (ABS). ? Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) or also known as a Power Inverter Module (PIM).
S14080003842024-01-02. Service bulletin. BACK OVER PREVENTION; LANE DEPARTURE. Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
90033572024-01-02. Service bulletin. BACK OVER PREVENTION. ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
90044522023-10-30. Service bulletin. BACK OVER PREVENTION: SENSING SYSTEM: CAMERA. CAMERA, Rear View Prior to replacement, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
S18080001522023-10-02. Service bulletin. VEHICLE SPEED CONTROL:ACCELERATOR PEDAL; BACK OVER PREVENTION. CEL (Check Engine Lamp) Illuminated, P057B Brake Pedal Position Sensor Performance
91001332023-07-31. Service bulletin. BACK OVER PREVENTION. ROCKER ARM ASSY - ROLLER ROCKER Case 1.- Before replacing the intake or exhaust rocker arms due to an abnormal ticking noise, please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head (no need to replace rocker arms). The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. Case 2.- If the INTAKE camshaft or INTAKE rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).
08-009-232023-02-13. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION. UAR and UCR Radio Enhancements Customers may experience one or more of the following: **Wi-Fi hotspot connection failure. Speaker popping, crackle noise during Voice Recognition (VR) response. Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** Lost radio presets. High pitch chime noise. Contact list not loading. Remote app inoperative. High pitch squeal, pop or humming sound coming from all of the speakers. Backup camera gridlines missing. Radios resets when a wireless connectivity paired phone receives two text messages one after another simultaneously after approximately seven seconds. (Sales Code ABD). Speaker crackling noise. Unable to adjust volume. Radio may reset /reboot, turn itself off and then back on. Active call not transferred to vehicle wireless connectivity. Voice Recognition (VR) not understanding commands. Wireless connectivity phonebook not available. Anti-theft code request message. Lines appear across screen. Radio will not switch modes between AM, FM, SAT or Media. Poor wireless connectivity sound quality. Phone pairing issues. In addition, the following enhancement is included in this update: Wireless connectivity pair or connection improvements. This bulletin involves inspecting and if required, updating the radio software level to **40.1. Depending on the radio?s current software level the radio may need a one or two USB update.**
08-010-232023-02-13. Service bulletin. BACK OVER PREVENTION. UGV UJV UKV and UCV Radio Enhancements Customers may experience one or more of the following: Arabic language missing (UJV only). Russian language missing (UGV only). PHEV vehicles may intermittently not charge when using the scheduled charging feature instead of ?Charge Now? button. When shifting to reverse, the radio displays blue/black lines instead of the rear view camera and is followed by a reset. Radio stays on with key ?OFF? and drains battery. Wi-Fi feature cannot be renewed after the trial period has expired. Radio reboots multiple times when a Samsung J-7T phone is connected for charging only. Audio System starts up with the anti-theft screen. Radio processor freezes while the navigation screen is loading. This bulletin involves inspecting and if required, updating the radio software level to: UJV or UGV - 21.9 UDV or UKV ? 19.11
S1623000028 Rev.2023-02-13. Service bulletin. VEHICLE SPEED CONTROL; BACK OVER PREVENTION; POWER TRAIN; VISIBILITY; PARKING BRAKE. Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
08093212023-01-17. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION. UAS, UAQ, UCS, UAV, UCV and UCQ Radio Over The Air Software Version Updates This bulletin provides information regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. This is part of a two step FOTA update, first update brings software level to 22.61 and this second FOTA update will take the software to 22.64. National launch for this second step is May 24, 2021. Customers may experience one or more of the following:Navigation is incorrect or can not calculate route. GPS locations is inaccurate. Uconnect radio apps are all inoperable. Backup camera screen is blue (DT and KL). Green horizontal lines appear across screen (DT and KL). Anti-theft code request message. Backup camera screen is blank. Lines appear across screen. Radio control screen is blank or locked. Radio reset intermittently. Unable to adjust audio volume. Unable to switch modes between AM, FM, SAT or Media. In addition the following enhancements are included in this update:Carplay® connectivity improvement. Improvement to Bluetooth® phone pairing. Bluetooth devices unresponsive. Improved sound quality when using a Bluetooth phone.
08-234-222023-01-17. Service bulletin. ENGINE AND ENGINE COOLING; STEERING; PARKING BRAKE; WHEELS; ELECTRICAL SYSTEM; BACK OVER PREVENTION. UAV and UCV Radio Enhancements Customers may experience one or more of the following: ? **Wi-Fi hotspot connection failure. ? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Lost radio presets. ? SXM favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Lost navigation settings. ? SXM icon inoperative (D-Truck). ? Radio display screen is black when the ignition is on (Rear View Camera (RVC) not affected (D-Truck)). ? Radio freeze intermittent (RVC not affected (D-Truck)). ? Wireless connectivity pair or connection issue (D-Truck). ? Radio channel changes by itself (D-Truck). ? Backup camera has black display screen, or Only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) (D-Truck). ? High pitch chime noise (D-Truck). ? Contact list not loading (D-Truck). ? ?Device Not Supported? message (D-Truck). ? Remote app inoperative (D-Truck). ? Travel-Link fuel price incorrect (D-Truck). ? Backup camera gridlines missing (D-Truck). ? Unable to adjust volume (D-Truck). ? Radio may reset/reboots, turn itself off and then back on again (D-Truck). ? High pitch squeal, pop or humming sound coming from all of the speakers (WK RU Only). ? Radio display screen is black, intermittent (RVC not affected (WK RU Only)). ? Radio freeze intermittent (RVC not affected (WK RU Only)). ? Navigation stuck on loading screen or not appearing at all (WK RU Only). ? Radios resets when a wireless connectivity paired phone receives two text messages one after another simultaneously after approximately seven seconds. (ABD sales code). ? Speaker crackling noise on non amplified vehicles (WK RU, UAV Only). ? Active cal
S20080000952023-01-09. Service bulletin. BACK OVER PREVENTION:DISPLAY FUNCTION. Service Shifter Is Displayed In the EVIC
90037562022-10-24. Service bulletin. BACK OVER PREVENTION; AIR BAGS; STEERING; PARKING BRAKE; ELECTRICAL SYSTEM. Rain light sensor Rain sense wipers do not operate: 1. Visual Inspection--> Check if the sensor is visually OK. (all the pins are OK) Check that the Connector is NOT loose (Sensor must get a voltage from 9V to 16V) 2. Functional Checks Rain--> Steering column switch is in auto mode (sensor is active) it is necessary to splash water on the sensitive surface of the sensor to trigger wipes. check the same for different sensitivities When the rain sensitivity is increased (for example from level 0 to level 1), as an acknowledgement a single wipe is seen. (This is not a phantom wipe) and this single wipe is not seen when the rain sensitivity is decreased (from higher level to lower level) Light--> Steering column switch is in auto mode (sensor is active) block the light coming on the sensor from outside of the vehicle (use a opaque object), the head lamps should be activated 3. If the sensor seems functional, it is ideal to remove the silicon gel pad from the sensor, replace it with the new silicon gel pad instead of replacing the whole sensor. When servicing the LRSM please replace the silicon gel pad with a new silicon gel pad (PN 68224945AA) instead of replacing the whole sensor.
S20230000422022-10-17. Service bulletin. BACK OVER PREVENTION. Wind Noise From Upper Corners Of Sliding Doors
S20080000932022-10-17. Service bulletin. LANE DEPARTURE: BLIND SPOT DETECTION. Blind Spot Or Park Assist Warnings, False Activation
S22230000082022-10-17. Service bulletin. BACK OVER PREVENTION. Squeak Noise Opening Front Doors
S2014000001RevA2022-09-26. Service bulletin. FUEL SYSTEM, GASOLINE:DELIVERY:PRESSURE SENSOR; FUEL SYSTEM, GASOLINE; BACK OVER PREVENTION; ELECTRICAL SYSTEM:WIRING:CONNECTORS/PLUGS/RECEPTACLES. (Revision A) When replacing the fuel line on a 2017-2018 RU 3.6L engine, it will be necessary to install a new fuel pressre sensor connector on to the vehicle harness. Follow the instructions below (or the I-sheet included with the part) when installing the connector repair kit.
S228A000004RevB2022-09-26. Service bulletin. BACK OVER PREVENTION. Panasonic VP4R Wi-Fi New Enrollment Pause
S21080000442022-09-26. Service bulletin. BACK OVER PREVENTION:DISPLAY FUNCTION. Display Flickering
08-130-212022-08-22. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; BACK OVER PREVENTION; ELECTRICAL SYSTEM; EXTERIOR LIGHTING; ELECTRICAL SYSTEM:PROPULSION SYSTEM:HYBRID MANAGEMENT. Flash: Battery Pack Control Module (BPCM) Diagnostic and System Updates This bulletin involves updating the BPCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0AA1-00 - Hybrid/EV Battery Positive Contactor ?A? Stuck Closed. P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck Closed. P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. P0B3C-00 - Hybrid/EV Battery Voltage Sense 1 Circuit Performance. P0B41-00 - Hybrid/EV Battery Voltage Sense 2 Circuit Performance. P0B46-00 - Hybrid/EV Battery Voltage Sense 3 Circuit Performance. P0B4B-00 - Hybrid/EV Battery Voltage Sense 4 Circuit Performance. P0B50-00 - Hybrid/EV Battery Voltage Sense 5 Circuit Performance. P0B55-00 - Hybrid/EV Battery Voltage Sense 6 Circuit Performance. P1A16-00 - Hybrid/EV Wakeup Control 3 Output Circuit/Open. P1D7B-00 - Hybrid/EV Wakeup Control 3 Output Circuit Short to Battery. P1D7C-00 - Hybrid/EV Wakeup Control 3 Output Circuit Short to Ground. P1A29 - Cell Supervisory Circuit A Failure. P1A2A - Cell Supervisory Circuit B Failure. P1D3E - Internal Control Module Shut Off Test Error. U0594 - Implausible Data Received from HCP. P2BE5 - Hybrid/EV Battery Pack Current Sensor "C" Circuit Performance. B12B0-85 - Charge Temperature Indicator-Signal Above Allowable Range. Customer may also experience one or more of the following: Premature oil change message displayed on the cluster and vehicle may be running in fuel/oil refresh mode. Scheduled charging not functioning properly because the battery pack did not wake up while plugged in.
08-017-212022-07-18. Service bulletin. BACK OVER PREVENTION; ELECTRICAL SYSTEM. Radio and Back-up Camera Enhancements This bulletin involves updating the radio software level to 1848.34. Customers may experience one or more of the following: Radio display screen flickers. Clock loses 6 seconds per day (JL with 5 inch screen). Green horizontal lines on back up display, in reverse (If this is the customer concern use camera LOP 18-60-02-Y7, on JL vehicles only). Ghost Touch, features, modes and App?s changing, without drivers input. Speaker pop noise when using Bluetooth® device. When vehicle is first started the radio will reset and the time display shows 12:00. Audio distortion and volume fluctuation. Blank rear camera image in reverse (If this is the customer concern use camera LOP 18-60-02-Y7 on JL vehicles only). Audio cutting in and out during memory recall. Ring tone too loud. AM/FM volume fluctuates. While in CarPlay® or AndroidAuto,® Google® maps showing wrong location. Phone disconnected after first call. Black screen or White screen with vertical lines. PIN clear and volume locked while KeySense is used. Audio static while in SXM/SAT modes. Echo heard during Bluetooth phone calls. The radio is locked up. The radio remains on after ignition has been turned off. The radio resets. The radio screen turns black. The radio screen shows messages ?Software Update? or ?Reinsert USB Device? and displays that screen in a continuous loop.
08-010-212022-07-18. Service bulletin. POWER TRAIN; EXTERIOR LIGHTING; ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING; BACK OVER PREVENTION. Flash: Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) Updates This bulletin involves reprogramming the HCP and AHCP or also known as Power Inverter Module (PIM) with the latest available software. Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states.Customers may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P06E4 - Control Module Wake-Up Circuit Performance. P2797-00 - Auxiliary Transmission Fluid Pump Performance. P07B5-00 - Park Pawl Position Sensor 1 Circuit Performance. P177C-00 - Park Lock-Pawl Actuator Motor Current Sensor Performance. P288B-00 - Park Lock-Pawl Actuator Circuit Performance. P0CF3-00 - Control Pilot Circuit Open(North America Only). P0CF4-00 - Control Pilot Circuit Performance(North America Only). P0D57-00 - Proximity Detection Circuit Performance(North America Only). P1C68-00 - Hybrid Perf Engine Speed Above Target Idle Speed During Autostop(APAC China Only). Customers may also comment:Vehicle will not start when it is cold -30° C (-22° F) and below. Heard and/or felt bump when the gas engine turns on while driving. This software release includes the following software enhancement: Corrections to allow the vehicle to clear the permanent fault codes. Three modules are required to be flashed for this update to be effective, the following modules are all to be updated along with this HCP&AHCP update:Powertrain Control Module (PCM) Electronic Brake Booster Module (EBBM). Anti-Lock Brake System Module (ABS).
S21080000932021-05-24. Service bulletin. BACK OVER PREVENTION:DISPLAY FUNCTION; EQUIPMENT. Apple CarPlay Does Not Work Or Not Connecting
08-017-212021-02-16. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION. Radio and Back-up Camera Enhancements This bulletin involves updating the radio software level to 1848.34. Customers may experience one or more of the following: Radio display screen flickers. Clock loses 6 seconds per day (JL with 5 inch screen). Green horizontal lines on back up display, in reverse (If this is the customer concern use camera LOP 18-60-02-Y7, on JL vehicles only). Ghost Touch, features, modes and App?s changing, without drivers input. Speaker pop noise when using Bluetooth® device. When vehicle is first started the radio will reset and the time display shows 12:00. Audio distortion and volume fluctuation. Blank rear camera image in reverse (If this is the customer concern use camera LOP 18-60-02-Y7 on JL vehicles only). Audio cutting in and out during memory recall. Ring tone too loud. AM/FM volume fluctuates. While in CarPlay® or AndroidAuto,® Google® maps showing wrong location. Phone disconnected after first call. Black screen or White screen with vertical lines. PIN clear and volume locked while KeySense is used. Audio static while in SXM/SAT modes. Echo heard during Bluetooth phone calls. The radio is locked up. The radio remains on after ignition has been turned off. The radio resets. The radio screen turns black. The radio screen shows messages ?Software Update? or ?Reinsert USB Device? and displays that screen in a continuous loop.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.