WenmarOpen by Wenmar Pro

Service bulletins for the 2020 BMW X6

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

301 on file from NHTSA, as of 2026-10-19.

By type

By component

By topic

Bulletins, newest first
B6303202020-04-20. Service bulletin. ENGINE AND ENGINE COOLING; AIR BAGS. Headlight Malfunction Check Control Message: Intermittently a check control message may be present stating "Adaptive headlight failure" (CC message 127) or "Headlight range control failure" (CC message 100). In conjunction one of the following faults codes MUST be stored for this bulletin to apply: 805A0D control unit: Headlight range control stepper motor driver failure (left frontal light module) 805A0E control unit: Adaptive Headlights stepper motor driver failure (left frontal light module) 805B8D control unit: Headlight range control stepper motor driver failure (left frontal light module) 805A0E control unit: Adaptive Headlights stepper motor driver failure (right frontal light module) This only affects vehicles with a current I-level below S18A-20-03-524. Software error in the FLM02 (Frontal light electronics module-Right or left).
B3405172020-04-20. Service bulletin. BACK OVER PREVENTION; SERVICE BRAKES, HYDRAULIC; WHEELS; POWER TRAIN. TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Ticking noise coming from front wheel while cornering without brakes applied noticeable at low speeds. The vehicle must be moving. See attached video V34 01 20 Note: For a similar noise heard when parking with the brakes applied refer to SIB 31 01 12. Microscopic movement of the contact interface between the inner brake disc and the wheel bearing flange on vehicles equipped with lightweight brake discs.
B1702202020-04-20. Service bulletin. ENGINE AND ENGINE COOLING. COOLANT LEAKING FROM THE LOW TEMPERATURE COOLING SYSTEM (B58C ENGINE): This Service Information Bulletin (Revision 1) replaces SI B17 02 20 dated March 2020. Premature breakdown of the coolant with gassing in the low temperature cooling system.
B1203202020-04-20. Service bulletin. ELECTRICAL SYSTEM. SERVICE ACTION: INSPECT AND SECURE THE ENGINE ELECTRICAL HARNESS: An improperly routed engine wiring harness may become damaged if it contacts the air conditioning (AC) compressor pulley.
B6631192020-03-16. Service bulletin. BACK OVER PREVENTION; ELECTRICAL SYSTEM. REARVIEW CAMERA. SPORADICALLY NO IMAGE IS DISPLAYED: This Service Information Bulletin (Revision 1) replaces SI B66 31 19 dated October 2019. When reverse gear is selected or the rear view camera is activated sporadically no image is displayed on the Central Information Display (CID). If the ignition is cycled off and back on the function is restored. Software error between the head unit and the rear-view camera.
B6101202020-03-16. Service bulletin. ELECTRICAL SYSTEM. ACCESSORIES DO NOT POWER ON: Customer is not able to power accessories using the 12 volt power socket. Design change to reduce short circuits and blown fuses.
B5105202020-03-16. Service bulletin. FUEL SYSTEM, GASOLINE. FUEL FILLER DOOR STICKING: The fuel filler door may be sticking requiring multiple attempts to open. The fuel filler door material can swell in wet conditions causing the filler door to stick.
B1701202020-03-16. Service bulletin. ENGINE AND ENGINE COOLING. SERVICE ACTION: ADD SILICONE BOOSTER TO LOW TEMP COOLING SYSTEM: The coolant in the low temperature cooling system may not have sufficient coolant corrosion protection.
B8402202020-02-18. Service bulletin. ELECTRICAL SYSTEM. REMOTE 3D VIEW NOT AVAILABLE: Remote 3D View cannot be launched In the BMW ConnectedDrive App. Software error in the Advanced Telematics Module 2 (ATM2).
B8401202020-02-18. Service bulletin. ELECTRICAL SYSTEM. BMW CONNECTEDDRIVE SERVICES ARE NOT AVAILABLE: The BMW ConnectedDrive services are not available for an extended period. This may include: Calls in the BMW Assistance app (Concierge Service) Vehicle data and status in the BMW ConnectedDrive app Remote services Remote 3D View Real Time Traffic Information (RTTI) Weather News Software error in Advanced Telematics Module 2 (ATM2).
B1701202020-02-18. Service bulletin. ENGINE AND ENGINE COOLING. SERVICE ACTION: ADD SILICONE BOOSTER TO LOW TEMP COOLING SYSTEM: The coolant in the low temperature cooling system may not have sufficient coolant corrosion protection. AFFECTED VEHICLES Vehicles which require this Service Action to be completed will show it as "Open" when checked either in AIR the "Service Menu" of DCSnet (Dealer Communication System) or with ISPA NEXT.
B1204192020-02-18. Service bulletin. ENGINE AND ENGINE COOLING. DME FAULT MEMORY ENTRY FOR THE CRANKSHAFT SENSOR: This Service Information Bulletin (Revision 1) replaces SI B12 04 19 dated February 2019. Technicians may notice this fault logged during a diagnostic session: Fault code: Control module: Fault Text: 160021 DME Crankshaft sensor: general loss of synchronism Environmental conditions are vehicle speed 0 (stationary) and engine speed less than 1500 rpm. There is no customer-facing symptom nor related check control message displayed. Phantom/pseudo fault due to unsuitable DME software. Background: After parking the vehicle and turning off the engine both DME control units go into sleep mode at different times. The DME of cylinder bank 2 ("secondary") goes into sleep mode first The DME of cylinder bank 1 ("primary") is still awake and can experience a reduction in signal voltage for the crankshaft sensor signal This signal change can mistakenly be evaluated as a skipped crankshaft sensor cog by the DME. If the engine is started while the primary DME is still awake this causes a brief loss of synchronization with the secondary DME. Fault 160021 is logged after three (3) consecutive engine starts with this momentary loss of synchronization. Note: Starting the engine after the primary DME has also gone into sleep mode will avoid the loss of synchronization.
B1112192020-02-18. Service bulletin. ENGINE AND ENGINE COOLING. MALFUNCTION INDICATOR LAMP IS ILLUMINATED WITH A CRANKSHAFT ADAPTION FAULT: When diagnosing an illuminated malfunction indicator lamp (MIL) and/or a different issue the following faults may also be stored in the Digital Motor Electronics (DME). Fault code Control module Fault code text 213A2B DME Increment wheel adaption faulty This situation is not associated with any drivability complaints and only affects vehicles built with a Factory I-level of 19-07-500 and later. An unfavorable DME diagnostic calibration may cause the fault code to be stored. In most circumstances this will cause the MIL to be illuminated.
B6629192020-01-21. Service bulletin. LANE DEPARTURE; BACK OVER PREVENTION. TOP VIEW CAMERA: IMAGE IS MISALIGNED. The top view image of the vehicle is misaligned when observed in the Control Information Display (CID). When the vehicle is parked in a parking spot with line markings it is clearly noticed in the CID that the lines are not parallel to the side of the vehicle. This may be noticed on either the driver side passenger side or both. The arrow identifies the line which is shown as not parallel or straight alongside the vehicle. Side view camera loose fitment in the exterior mirror bracket causing changes to the top view image.
B6210192020-01-21. Service bulletin. SERVICE BRAKES. INCORRECT CONDITION BASED SERVICE DATA FOR BRAKE FLUID SERVICE. "Brake fluid service due since 12/2001" is displayed in the instrument cluster although the vehicle is only a maximum of 1 year old. Software error in the KOMBI (Instrument Cluster).
B6209192020-01-21. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. INSTRUMENT CLUSTER REMAINS DARK AFTER STARTING THE VEHICLE: Instrument cluster remains dark after starting the vehicle. After a restart normal functionality is restored. Software error in the KOMBI (Instrument Cluster).
B3410192020-01-21. Service bulletin. SERVICE BRAKES. HELPFUL INFORMATION FOR CUSTOMER DISCUSSIONS REGARDING MOTORSPORT VEHICLE BRAKES: Note for customer deleted: If the noise does not disappear despite the attempts to regenerate the brake a repair is required.
B6522192019-12-16. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. NO AUDIO IS AVAILABLE FOR APPROXIMATELY 30 SECONDS AFTER HEAD UNIT START UP: After programming vehicle no audio is available for approximately 30 seconds after head unit start-up. Fault code B7F490 "Control unit reset" is present in the RAM (Receiver Audio Module).
B6510192019-12-16. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. ENGINE SPEED DEPENDENT NOISE DURING AUDIO PLAYBACK: Integration level updated. There is an engine speed-dependent noise heard through the speakers during audio playback. Software error in the Receiver Audio Module (RAM) control unit.
B6307192019-12-16. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING:BRAKE LIGHTS; EXTERIOR LIGHTING:TAIL LIGHTS. DELIVERY STOP: PROGRAMMING CONTROL MODULES (TAIL LAMPS). BMW of North America LLC has issued a Delivery Stop (effective October 24 2019) on a small number of Model Year 2020 BMW X6 vehicles that were produced in the date range shown above. In extremely rare instances dimming of the tail lamps in the "Welcome mode" and "Goodbye mode" could cause the left or rear tail lamps and/or brake lamps to not illuminate. It is unlikely that the left and right tail lamps will not illuminate simultaneously.
B6201192019-12-16. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. INSTRUMENT CLUSTER AND ONBOARD COMPUTER INTERMITTENTLY INOPERATIVE: Instrument Cluster (KOMBSP18) functions are intermittently inoperative including: On-board Computer (BC) button on turn signal stalk (BC button shown at left) Radio displays Menu button Turn signal displays Arrows on multifunction steering wheel MFL thumbwheel control.
B6123152019-12-16. Service bulletin. EQUIPMENT; VISIBILITY:WINDSHIELD WIPER/WASHER. Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full : The low washer fluid warning is illuminated even though the washer fluid reservoir is full. There are no faults stored in the system for the washer fluid level switch. A non-approved washer fluid was used that is silicone-based. Silicone-based fluids are not compatible with the contactless capacitive level sensor. Fluids that contain a silicone additive are normally colored other than blue.
B6122192019-12-16. Service bulletin. LATCHES/LOCKS/LINKAGES:DOORS:LATCH; STRUCTURE:BODY:DOOR; EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. DOORS LOCKED WITH REMOTE CONTROL INSIDE THE VEHICLE. The customer states that the vehicle locks itself when the last door was closed even though the remote control/display key was inside the vehicle. Sporadic interference causes the vehicle to revert to "outside detection" of the vehicle remote control instead of "inside the vehicle detection" which is where the key was located.
B3410192019-12-16. Service bulletin. SERVICE BRAKES, HYDRAULIC; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. HELPFUL INFORMATION FOR CUSTOMER DISCUSSIONS REGARDING MOTORSPORT VEHICLE BRAKES: INFORMATION Inform the customer during a consultation that the M Compound (standard equipment) and M Carbon Ceramic (optional) brakes are high-performance brake systems which are designed for sporty dynamic driving styles. As a side effect of the highest possible brake performance customers are likely to hear noises due to the extremely resilient materials.
B1228192019-12-16. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. THE MIL MAY BE ILLUMINATED BY ERRONEOUS VALVETRONIC FAULTS. One of the following faults may be stored in the digital motor electronics (DME) either as part of diagnosing a different issue; and-or an illuminated malfunction indicator lamp (MIL).

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.