WenmarOpen by Wenmar Pro

Service bulletins for the 2015 BMW X6

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

249 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
6522142018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Automated Activation of Navigation System During PDI/QC1. INFORMATION Important: The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1, the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system. Note: This VIN-specific NAV enabling code is then also automatically stored in the Repair Kit in the Aftersales Assistance Portal (ASAP). The automated INITIAL NAV enabling code request and activation of the navigation system will take no longer than 1 minute. After finishing "Delete Transport Mode," the navigation system in the vehicle will be active without entering the 20-digit INITIAL NAV enabling code manually or in ISTA. If the navigation system is not active and asking for the enabling code, turn off the ignition and wait for the head unit to enter sleep mode (approx. 3 minutes). After that, turn on the ignition again. The head unit will start up and the navigation system is activated. If the INITIAL NAV enabling code for first-time activation of the navigation system is not requested or delivered automatically, it still can be ordered manually through the Parts department and activated in the vehicle through the iDrive controller, by entering the 20-digit enabling code manually.
6313142018-11-13. Service bulletin. SERVICE BRAKES, HYDRAULIC; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EXTERIOR LIGHTING:TAIL LIGHTS; ELECTRICAL SYSTEM:WIRING. Service Action: Radio Reception Interference Due to Taillight. A Service Action for a Delivery Stop has been issued on certain F16 vehicles produced from August 1, 2014 through October 30, 2014. When the brakes are applied, there is an interference noise from the radio in the very high frequency range from 104 MHZ to 107 MHZ. Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at ports of entry will be repaired prior to dealer delivery. Affected vehicles can be identified with a "Vehicle Comment" in DCS Warranty Vehicle Inquiry, or ISPA Light with the description CAUSE Faulty hardware in the left rear taillight
6133142018-11-13. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT ADAPTIVE/MOBILITY. The Controller Responds Slowly or Not at All. When the customer presses or turns the controller, there is no or a delayed response. This can sporadically occur. Software in the controller
B6212152018-11-13. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Instrument Cluster Outside Temperature Display Implausible. INFORMATION This service information bulletin provides technical, diagnostic and/or repair-related information. Eligible and Covered Work/Repairs To submit a claim for the repair of a verified defect in materials or workmanship, please following the established and applicable warranty policy and procedures together with the using corresponding defect code and labor operations provided in the KSD2.
B6130142018-11-13. Service bulletin. ELECTRICAL SYSTEM. "?SI B61 30 14December 2015 General Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B61 30 14 dated July 2015. designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is ""applicable"" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months. "
B6608152018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Comfort Access Does Not Function After Vehicle Enters Sleep Mode. Sporadically, when the vehicle has been locked and is in sleep mode, the vehicle will not waken when trying to unlock the vehicle with comfort access from any door. The vehicle can be unlocked from the remote. After waking, the comfort access function is restored. Software fault in the BDC.
B6509152018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL. HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
B6210152018-11-13. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. "Instrument Cluster display inoperative FC B7F689. The Instrument Cluster (Kombi) is intermittently inoperative with fault code B7F689 ""display backlighting and graphics PCB switched off"" stored. Kombi software."
B6207152018-11-13. Service bulletin. ELECTRICAL SYSTEM. "Instrument Cluster display is partially blank. INFORMATION Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks or the BMW Certified Pre-Owned Program. If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowances. Vehicle Programming and Encoding If a control module was working properly and it fails to program correctly or requires initialization, please claim this additional work with the applicable KSD2 labor operations under the defect code listed above. The diagnosis and repair of vehicles ""arriving"" with failed control modules or stored faults which will cause them to fail during programming cannot be claimed under the defect code listed in this bulletin. Other Repairs If other eligible and covered work is performed ""prior"" to programming and coding the vehicle, claim this work with the applicable defect code and labor operations listed in KSD2. "
B6207152018-11-13. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Instrument Cluster display is partially blank. The Instrument Cluster (Kombi) lower display may be intermittently blank. The Board Computer, Ambient Temperature and Check Control Messages will not display. Instrument Cluster software error.
B6204152018-11-13. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; ELECTRICAL SYSTEM:SOFTWARE. Service Action: Programming Control Units. Sporadically the vehicle cannot be started, due to a discharged battery caused by a software glitch in the instrument cluster.
B6205162018-11-13. Service bulletin. ELECTRICAL SYSTEM. Head-up Display is no Longer Visible. HUD (Head-up Display) adjusted to the lowest position is no longer visible. Software in the instrument cluster
B6111152018-11-05. Service bulletin. SEATS; SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER; ELECTRICAL SYSTEM. Rear Seat Heater Inoperative. The front passenger and both rear seat heaters do not work. The following fault codes are stored in the BDC (Body Doman Controller): D90C18 - LIN master I: Short circuit D90C1A - LIN master I: Communication faulty CAUSE One of the rear seat heater modules has an internal fault, which interrupts LIN bus communication.
B1223152018-11-05. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ELECTRICAL SYSTEM:SOFTWARE; VEHICLE SPEED CONTROL. "Reduced Engine Power with ""Charging Pressure Too High"" Faults Stored. When accelerating under certain conditions, the engine power may be reduced and a Check Control Message (CCM) ""Drive Faulty; Drive at moderate speed"" is displayed. The following charging pressure control fault is stored in the DME: ? Fault 120208: Exhaust camshaft sensor, signal: not plausible As a result, the engine power is reduced, and the following faults may also be set: ? Fault 120408: Charging pressure control: Switch-off, pressure build-up blocked ? Fault 120908: Charging pressure control2: Switch-off, pressure build-up blocked CAUSE DME software error"
B1221142018-11-05. Service bulletin. FUEL SYSTEM, OTHER:STORAGE:FUEL GAUGE SYSTEM; ELECTRICAL SYSTEM:SOFTWARE; FUEL SYSTEM, GASOLINE. Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
B1221142018-11-05. Service bulletin. ELECTRICAL SYSTEM. ?SI B12 21 14May 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated April 2015. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
6201152018-11-05. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. SUBJECT Head-Up Display Information No Longer Visible. The Head-up Display information is no longer visible on the windshield. The Head-up Display has moved downwards to the lowest possible position and can no longer be adjusted to a higher position. Software error in the instrument cluster
1221142018-11-05. Service bulletin. ENGINE; ELECTRICAL SYSTEM. SI B12 21 14February 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated December 2014. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: z FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
B6618162018-11-05. Service bulletin. ELECTRICAL SYSTEM. INFORMATION ON THE OPERATION OF THE SMART OPENER. INFORMATION ON THE OPERATION OF THE SMART OPENER MODEL F07 (5 Series Gran Turismo) F10 (5 Series) F12 (6 Series Convertible) F13 (6 Series Coupe) F15 (X5) F16 (X6) F22 (2 Series Coupe) F23 ( 2 Series Convertible) F25 (X3) F26 (X4) F30 (3 Series Sedan) F31 (3 Series Wagon) F32 (4 Series Coupe) F33 (4 Series Convertible) F34 (3 Series Gran Turismo) F36 (4 Series Gran Coupe) F48 (X1) F80 (M3 Sedan) F82 (M4 Coupe) F83 (M4 Convertible) F85 (X5 M) F86 (X6 M) G12 (7 Series) I01 (i3 Series) Vehicles with option code SA-0322 (Comfort Access) without M-Sport trim INFORMATION The smart opener (Contactless tailgate) operates as described below: Ignition key must be within 3 feet behind the vehicle, clear from any interference like a smartphone The customer must be at least an arms-length behind the vehicle Kick your foot forwards & backwards under the vehicle in one quick movement The taillights flash confirming that the trunk will open The trunk then successfully opens For more information an instructional video can be viewed which demonstrates the operation. Thanks to BMW of Tenafly for providing the video. tinyurl.com/Autotrunk1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016 Page 2 of 2 WARRANTY INFORMATION Not applicable. [ Copyright (c)2016 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016
B0112162018-11-05. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. "N63T PRESSURE SWITCH - LEAK DIAGNOSIS MODULE (NVLD): LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES. INFORMATION For the above-referenced vehicles, BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the pressure switch, leak diagnosis module (NVLD) to: 10 years/120,000 miles as determined by the vehicle's original in-service date Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, BMW NA will be sending VIN-specific customer notification letters in a phased release."
B0110162018-11-05. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. "N55 PRESSURE SWITCH - LEAK DIAGNOSIS MODULE (NVLD): LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES. INFORMATION For the eligible vehicles, BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the pressure switch, leak diagnosis module (NVLD) to: 10 years/120,000 miles as determined by the vehicle's original in-service date of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, BMW NA will be sending VIN-specific customer notification letters in a phased release."
B6523162018-11-05. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. ?AUDIO VOLUME NOT RESTORED AFTER MSA STOP, ENTRY HEAD UNIT. Volume of audio system (when set to near maximum) is reduced when Auto Start-Stop (MSA) stop occurs and is not restored upon automatic engine restart. This is normal system behavior - serves to protect the head unit, battery drain and avoidance of incremental leaps in the loudness. The loudness is reduced to 2/3 of maximum and is not restored. Note: Air conditioning output is also reduced upon MSA stop and is not restored for similar reasons.
B6130142018-11-05. Service bulletin. ELECTRICAL SYSTEM. "?BMW Maintenance Program: 12-Volt Battery Replacement Measure What's new: ? "Models" updated: Model Year 2017 vehicles added ? "Models" updated: Model Year G12 (7 Series) excluded from program ? "Procedure" updated: N63R engine added to 2016 Model Year G12 (7 Series) ? Attachment updated with G12 (7 Series) production date range for 2016 Model Year. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is "applicable" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."
B6506162018-11-05. Service bulletin. ELECTRICAL SYSTEM. ?NBT HEAD UNIT ABORTS IMPORT OF CD Whats New: ? G12 (7 Series) removed ? I01 (i3) removed ? Warranty Section updated for removal of G12 and I01 . While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software
B8408182018-08-06. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM. HEAD UNIT HIGH 2 RESET WHILE BLUETOOTH IS CONNECTED: The following event may cause an unexpected reset of the Head Unit High 2 (NBT EVO) when:

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.