WenmarOpen by Wenmar Pro

Service bulletins for the 2013 BMW X3

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

368 on file from NHTSA, as of 2026-10-19.

By type

By component

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
B6121152018-12-10. Service bulletin. ELECTRICAL SYSTEM:WIRING; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. The Instrument Cluster Displays Various Check Control Messages. The instrument cluster displays various check control messages. Signal invalid. The wiring harness below the micro filter housing (right front area of the bulkhead) is damaged from washer fluid leaking into the harness.
B8403142018-12-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. SI B84 03 14 February 2016 Communication Systems Technical Service This Service Information bulletin supersedes SI B84 03 14 dated October 2014. SUBJECT Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures CAUSE Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware CORRECTOPM None available at this time. We are currently working with the device manufacturer on a solution.
B6601162018-12-10. Service bulletin. BACK OVER PREVENTION: SENSING SYSTEM: CAMERA; ELECTRICAL SYSTEM:SOFTWARE. SUBJECT TRSVC Control Unit Cannot Be Programmed. During ISTA/P session, ISTA/P requests that the TRSVC (Top Rear Side View Camera) control unit be replaced because ISTA/P cannot program it. Software error in the TRSVC control unit
B6502162018-12-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
B6103142018-12-10. Service bulletin. ELECTRICAL SYSTEM. February 2016 General Electrical Systems Technical Service This Service Information bulletin supersedes SI B61 03 14 dated May 2015. SUBJECT Check Control Messages Related to Battery Charge during Cold Ambient Temperatures. On cold days (an outside ambient temperature below 15F), customers may notice a check control message related to the battery displayed on the instrument cluster and the control information display. The check control message (ID 229) is caused by a heavily discharged battery. The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit).
B6203162018-12-10. Service bulletin. ELECTRICAL SYSTEM. ?Clock gains or loses time. The time displayed in the KOMBI (instrument cluster) may gain or lose a few minutes each week. Internal KOMBI calculation error.
B6121152018-12-10. Service bulletin. VISIBILITY:WINDSHIELD WIPER/WASHER; ELECTRONIC STABILITY CONTROL (ESC); ELECTRICAL SYSTEM:WIRING. The Instrument Cluster Displays Various Check Control Messages. This includes messages for the PDC (Park Distance Control), DSC (Dynamic Stability Control) and windshield washer system. There can be many different fault codes stored in the vehice. Signal invalid. The wiring harness below the micro filter housing (right front area of the bulkhead) is damaged from washer fluid leaking into the harness.
B8407162018-12-10. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ELECTRICAL SYSTEM:SOFTWARE. ?After programming with ISTA/P 3.55.0 or a more recent version, the customer can no longer send ?Edit start time? signal for climate control system can only send an ?Activate now? signal for climate control system.
B6121152018-12-10. Service bulletin. VISIBILITY:WINDSHIELD WIPER/WASHER; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; ELECTRICAL SYSTEM:WIRING. THE INSTRUMENT CLUSTER DISPLAYS VARIOUS CHECK CONTROL MESSAGES. The instrument cluster displays various check control messages. THE INSTRUMENT CLUSTER DISPLAYS VARIOUS CHECK CONTROL MESSAGES. The instrument cluster displays various check control messages. This includes messages for the PDC (Park Distance Control), DSC (Dynamic Stability Control) and windshield washer system. There can be many different fault codes stored in the vehicle. The wiring harness below the micro filter housing (right front area of the bulkhead) is damaged from washer fluid leaking into the harness.
3406122018-12-03. Service bulletin. ELECTRICAL SYSTEM. DSC Warning Light is On. The warning lamps for DSC, ABS and brake warning are illuminated. There may also be a warning in the control display for 'Chassis Control System failure' One or more of the following fault codes are stored: DSC ??D36D44 - Signal error longitudinal torque distribution (LMV) ??48097D - Transfer Case clutch position open CAUSE Software calibration error in the LMV
6514132018-12-03. Service bulletin. ELECTRICAL SYSTEM. SPORT Mode Is Incorrectly Deactivated or Added After Programming. After programming the vehicle with ISTA/P 2.47.0 or higher: * Vehicles with the Dynamic Driving Switch: The SPORT configuration menu is no longer available in the control display. * Vehicles without the Dynamic Driving Switch: The SPORT configuration menu is available in the control display but does not function. There is no button next to the gear shifter. Software error in the head unit caused by ISTA/P versions from 2.47.0 to 2.49.x
6305132018-12-03. Service bulletin. ELECTRICAL SYSTEM. "FRM3 Will Not Communicate with ISTA. When diagnosing the vehicle with ISTA, the FRM3 (Footwell Module) is shown as not responding in the vehicle test. The customer may report one or more of the following malfunctions: 1. Light operation * CCM (Check Control Message) ""Display failure"" * Lighting INOP * Turn signal lights INOP * Break lights INOP * License plate light INOP * Courtesy lights INOP * Instrument cluster w/o light 2. Windows * One or both front windows INOP 3. LIN components https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15625.1.B630513... 8/29/2013 Page 2 of 2 * CCM ""no blind spot detection"" if equipped * Power mirrors INOP * Seat adjustment INOP 4. Hardware inputs * Door locks INOP * Gear shifts automatically to P * Gear shift lever cannot be moved out of P 5. Electrical steering column adjustment * ELSV (Electric Steering Column Adjustment) INOP CAUSE Various causes include the following: * Blown fuse * Faulty wiring * Faulty component"
6518132018-12-03. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Touchpad Integrated in the iDrive Controller Is Intermittently Inoperative. Intermittently the Touchpad integrated in the iDrive controller is inoperative. * No entries can be made using the Touchpad * Fault code is stored in the touch-box control unit Software error in the touch-box control unit (TBX)
6307132018-12-03. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Daytime Running Light Does Not Switch ON. The DRL (Daytime Running Light) is off and cannot be switched on after importing the personal profile from another vehicle. The CID (Central Information Display) display shows that it is active. CAUSE Software error when importing the personal profile from a vehicle which has a different head unit
6122132018-12-03. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. """Increased battery discharge!"" CC Message upon Startup. CAUSE A software error in the Intelligent Battery Sensor causes an incorrect State of Charge (SoC) to be stored in the DME. The power management system then interprets this as a heavily discharged battery and informs the customer via a CC message. In reality, the battery does not have a problem."
6601132018-12-03. Service bulletin. ELECTRICAL SYSTEM. PDC: Complete Failure of Front and/or Rear Sensors. When reverse gear is selected or the PDC button is pressed, neither the front and/or rear PDC sensors work. One or more of the following fault codes are stored: * 0x803200 - Voltage supply for ultrasonic sensors * 0x80320A - Rear outer left ultrasonic sensor * 0x803210 - Rear centre left ultrasonic sensor * 0x803216 - Rear centre right ultrasonic sensor * 0x80321C - Rear outer right ultrasonic sensor * 0x80322E - Front outer left ultrasonic sensor * 0x803234 - Front centre left ultrasonic sensor * 0x80323A - Front centre right ultrasonic sensor * 0x803240 - Front outer right ultrasonic sensor CAUSE Short circuit in the wiring harness for the PDC ultrasonic sensors
6509132018-12-03. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL. "CHAMP2: Stored Radio Stations Deleted After Ignition Off. After ignition off, the stored radio stations (AM/FM and Satellite) are no longer available in: * Menu ""PRESETS"" * Functional bookmarks (buttons on the head unit) Error in the CHAMP2 head unit"
6113122018-12-03. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. ?100A Fuse in Rear Power Distribution Box Failed, Causing Electrical System Failure. Various functions of the electrical system fail. In rare cases, the vehicle cranks but may not start. The 100-amp fuse (F502) in the rear power distribution box (Z3), mounted on the battery, has failed.
6106132018-12-03. Service bulletin. ELECTRICAL SYSTEM. "Rear Washer Pump Continues to Operate with Key Off. The rear washer pump continues to run after the vehicle is locked or unlocked with the key off. In some cases, turning the ignition on stops the pump from running. CAUSE The JBE (Junction Box Electronics) module fails as a result of voltage spikes caused by the door locks. One or more of the following faults may be stored: * JBE - ""8020A8 Window washer pump, rear: short circuit to ground"" * IHKA - ""E71452 CAS interface (status, central locking system, 0x2FC): Signal invalid"" * KOMBI - ""E12C1A Interface CAS (central locking and lid status, 0x2FC): Signal invalid"""
6102112018-12-03. Service bulletin. ELECTRICAL SYSTEM. Advanced Onboard Battery Diagnostics. INFORMATION Starting with the introduction of the F10 (5 Series), an advanced intelligent battery sensor has been used. This now makes it possible for the vehicle to monitor the condition of the battery in order to determine if the battery needs to be recharged or replaced, along with the remaining capacity of the battery. The analysis and testing of the battery's SoC (State of Charge) and SoH (State of Health) is now performed using ISTA (Integrated Service Technical Application) diagnosis. A separate test using a battery tester is no longer needed.
6206132018-12-03. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Condition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster
B8406162018-12-03. Service bulletin. ELECTRICAL SYSTEM. ?BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. BMW Online/BMW ConnectedDrive not functional. Vehicle and service cockpit have different ICC-ID's (Integrated Circuit Card Identifier).
B8402142018-12-03. Service bulletin. ELECTRICAL SYSTEM. ?CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
6138122018-11-26. Service bulletin. ELECTRICAL SYSTEM. "Service Action: Program Control Units (CAS). After programming/coding the vehicle with ISTA/P 2.48.1 or earlier, the Car Access System (CAS) was incorrectly coded. This causes the anti-theft alarm system panic button on the remote control to not function. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 637. If code number 637 has been punched out, the campaign has already been performed. If code number 637 has not been punched out, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action. Important Note: A campaign can be reserved in ISPA Light as ""Pending"" prior to submission of a claim. If you find this campaign reserved, please verify the reason before attempting to perform this repair."
2702122018-11-26. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. "The warning lamps for DSC, ABS and brake warning are illuminated. There may also be a warning in the control display for ""Chassis Control System failure."" One or more of the following fault codes are stored: DSC: * D36D44 - Signal error longitudinal torque distribution (LMV) * 48097D - Transfer Case clutch position open F01, F02, F07, F10, F12 and F13 LMV: * 440108 - Control Unit internal error * 44010F - Control Unit internal error E70, E71 and E84 LMV: * 5219 - Control Unit: EEPROM Writing-reading-error * 522D - Control Unit: internal Error CAUSE Software calibration error in the LMV"

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.