WenmarOpen by Wenmar Pro

Service bulletins for the 2014 BMW 650i

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

344 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
B1205162018-12-10. Service bulletin. ENGINE. "N55 - Engine Malfunction Warning Due to Vapor Forming in the Fuel System. The Engine Drivetrain Malfunction"" Check Control warning is displayed and the Service Engine Soon (MIL) Lamp may also be on. In areas where winterized fuel is used, this situation may occur after prolonged periods of engine idling or ""stop and go"" driving. Additional symptoms that may be present: rough running poor engine performance difficulty in starting the engine. Either or both of the following fault codes can be stored in the DME. 11A002 - Fuel high pressure, plausibility: Pressure too low 11AC02 - Fuel high pressure, plausibility, cold start: Pressure too low In addition any of the following faults may also be stored: 119404 - Rail pressure sensor, signal: Permanently stuck 118001 - Mixture control: mixture too lean 118401 - Mixture control: mixture too lean; large deviation Vapor formation in the fuel system from fuel quality characteristics of certain winter fuel blends along with high engine compartment temperatures."
1107132018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. N63T Engine: New Test Plan to Check Engine Oil Level with ISTA/D 3.39.21. INFORMATION With the release of ISTA/D 3.39.21, a new test plan is available for checking the engine oil level in some vehicles with the N63T engine. The test plan will help identify the actual oil level, and advise the amount that will need to be added to correctly fill the engine when topping up. When performing the scheduled oil service and filling the engine with the amount specified, the applicable ISTA/D repair instruction does not require performing this test plan. Applicable models: * F01 and F02 with the N63T engine, produced from 3/2013 and later with I-Level F001-13-03-501 or higher * F06, F07, F12 and F13 with the N63T engine, produced from 3/2013 and later with I-Level F001-13-03-501 or higher * F10 with the N63T engine produced from 7/2013 and later with I-Level F010-13-07-501 or higher Test plan path: Service Function/Drive/Motor Electronics/Motor Oil/Oil Level IMPORTANT: Do not perform this test plan on the following vehicles: * E70, E71, F01, F02, F04, F06, F07, F12 and F13 vehicles with the N63 or N63T engine, produced before 3/2013 l * F10 vehicles with the N63 engine produced before 7/2013 If this test plan is performed on these vehicles, the result is an incorrect measurement and level indication; overfilling of the engine will occur. Overfilling of the engine will result in engine damage. When a solution for vehicles which are not at one of the integration levels above is available, it will be communicated promptly. WARRANTY INFORMATION Not applicable. [ Copyright (c)2013 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15702.1.B11071... 11/12/2013
1206132018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. The Service Engine Soon Lamp On with Post Oxygen Sensor Faults Stored. The Service Engine Soon (MIL) lamp is on and the following faults are stored in the DME fault code memory. BN2000 (E-Series) vehicles: * 2D22: Oxygen sensor downstream of catalytic converter, electric: open circuit BN2020 (F-Series) vehicles: * 12AB04: Oxygen sensor downstream of catalytic converter, electric: open circuit * 12AC04: Oxygen sensor downstream of catalytic converter 2, electric: open circuit These faults may occur sporadically after a long MSA engine stop. Unfavorable DME software diagnostics (fault is erroneous) This software error affects vehicles produced from 3/2013 to 6/2013, as well as older vehicles which have been programmed during service work to a current integration level of Xxxx-13-03-5xx.
1219132018-12-03. Service bulletin. ENGINE; ELECTRICAL SYSTEM. ?Service Action: Program Control Units (Oil Level Sensor). Due to a signal error from the oil level sensor, the vehicle could display an erroneous message indicating that an oil service is due after only a short distance has been traveled.
1218132018-12-03. Service bulletin. ENGINE; ELECTRICAL SYSTEM. N63: Service Engine Soon Lamp (MIL) Is On with Fault 1D2008 Stored. Under certain low-load driving conditions at low outside ambient temperatures, the following fault may be stored in the DME with the Service Engine Soon lamp (MIL) on: Fault 1D2008 - Map thermostat, mechanical: jammed open. However, the thermostat is found to be operating correctly with sufficient heat output from the climate control system, and the engine is operating at the correct temperature. Unfavorable DME software diagnostic
1217132018-12-03. Service bulletin. ENGINE; POWER TRAIN. N55: Engine Difficult to Start at Cold Ambient Temperatures. The complaint may include any of the following symptoms: * The engine stalls immediately after a cold start before driving away * The engine may run roughly or misfire after a cold start * The engine does not start cold or may take several attempts * To assist starting when cold, the accelerator may need to be depressed slightly and the idle speed raised for a few seconds so the engine does not stall This can occur most frequently at outside ambient temperatures between -15°C and + 15°C. It is possible that the Service Engine Soon (MIL) lamp is on with misfire fault(s) stored, but it is equally possible that there will be no faults stored in the DME. Unfavorable DME software Cold start or idling problems may arise due to poor fuel quality. The use of summer fuel during cold outside temperatures may also lead to such problems.
1307122018-12-03. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
1216112018-12-03. Service bulletin. ENGINE; POWER TRAIN. N55 Engine Failsafe - FC 120308 Boost Pressure Control, Plausibility: Pressure Too Low Stored in DME Fault Memory. INFORMATION The customer complains the SES is illuminated and the engine has reduced power (engine failsafe mode).
1214132018-12-03. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. BMW centers must ensure recalls are completed after having been notified by BMW of North America, LLC (BMWNA) that a safety-related defect or noncompliance exists in any motor vehicle or item of replacement equipment in the center's possession at the time of notification. In BMW NA's case, this notification would typically be made by the issuance of a recall notification in the form of a Service Information bulletin (SIB) or transmission of a Dealer Communication System (DCS) recall message. Under the National Traffic and Motor Vehicle Safety Act of 1966, as amended, if a recall campaign is announced by BMW NA, centers must ensure that all recalls on new vehicles and new items of replacement equipment are completed BEFORE delivery to the consumer. This means that centers may not legally deliver new motor vehicles or new items of replacement equipment to consumers with an open recall. The Safety Act also prohibits centers from selling or leasing the motor vehicle or item of replacement equipment, unless and until the open recall has been completed BEFORE delivery. This also pertains to vehicles in the Certified Pre-Owned program, and to items of replacement equipment. Finally, BMW centers should not sell or use parts that have been recalled by BMW NA. Please follow the specific instructions provided by BMW NA on the return or disposition of the parts. SUBJECT Voluntary Emissions Recall Campaign 13E-A01: Program Control Units (Tank Ventilation). Due an error in the DME (Digital Motor Electronics) software, the fuel tank ventilation system may not sufficiently purge the active carbon canister of accumulated fuel vapor under certain engine operating conditions. As a result, this may lead to a fuel smell around the vehicle, especially in areas with high ambient temperatures. In order to remedy the s
B1111172018-12-03. Service bulletin. ENGINE. ?ENGINE LEAK DIAGNOSIS ON TURBOCHARGED V8 ENGINES. When diagnosing an engine oil leak or a coolant leak on turbocharged V8 engines it is necessary to use a borescope to identify if the source of the leak is from under the turbochargers. Engine oil or coolant leaking from the bell housing area or the front timing chain cover area may be caused by the turbocharger itself, a turbocharger oil/coolant feed line or turbocharger oil/coolant return line. Do not remove the transmission and do not dissemble the engine before performing this inspection. If necessary, use engine oil leakage detection dye.
1307122018-11-26. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
1205132018-11-26. Service bulletin. ENGINE. Service Engine Soon Light Flashes with Throttle Adaptation Faults Stored. The EML light flashes with a check control message for reduced power output and/or the Service Engine Soon lamp (MIL) flashes. During the throttle valve adaptation (teach-in limit run), faults may occur due to signal voltage oscillations. This could lead to a termination of the teach-in routine or an incorrect value taught in at the lower limit. The following faults can be stored in the DME memory: E82, E84, E88, E89, E92, and E93 BN2000 vehicles * 28D0: throttle valve, adaptation: Initial adaptation, lower limit not taught in * 28D4: throttle valve, adaptation: Subsequent teach-in, lower limit not taught in * 28C4: throttle valve, adaptation: Emergency air position not adapted * 28A0: throttle valve angle - Intake manifold absolute comparison: pressure too high ??3166: Tank-ventilation system: fault F01, F02, F06, F07, F10, F12, F13, F30, F31, and ALPINA B7 BN2020 vehicles: * 101408: throttle valve, adaptation: Initial adaptation, lower limit not taught in * 107AE0: throttle valve, adaptation: Subsequent teach-in, lower limit not taught in * 101402: throttle valve, adaptation: Emergency air position not adapted * 101F01: throttle valve angle - Intake manifold absolute comparison: pressure too high ??190F08: Tank-ventilation system: fault Sensitivity of the throttle valve sensor (only affects parts installed during this production period)
1101132018-11-26. Service bulletin. ENGINE. "N63 and N63T Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity. Customers with one of the vehicles above may complain that the engine's oil consumption is ""too high,"" resulting in engine oil top-ups and workshop visits to address the issue before the vehicle displays an engine oil service as being ""due."" When the vehicle's engine oil drops to the minimum level, a message will display in the vehicle advising the driver to ""add 1 quart of engine oil."" After topping up and continued operation, the ""add engine oil"" message may display again before an engine oil service is required and performed. CAUSE Engines that are fitted with a turbocharger, as part of their normal operation, will consume engine oil at a higher rate than a naturally aspirated engine (non-turbocharged engine). In this case, a ""turbocharged"" engine could require topping up of the engine oil more frequently."
B1101132018-11-26. Service bulletin. ENGINE. N63 AND N63T ENGINE: ENGINE OIL CONSUMPTION, ENGINE OIL TOP-UPS AND REFILL CAPACITY. Customers with one of the vehicles above may complain that the engine's oil consumption is "too high," resulting in engine oil top-ups and workshop visits to address the issue before the vehicle displays an engine oil service as being "due." When the vehicle's engine oil drops to the minimum level, a message will display in the vehicle advising the driver to "add 1 quart of engine oil." After topping up and continued operation, the "add engine oil" message may display again before an engine oil service is required and performed. CAUSE Engines that are fitted with a turbocharger, as part of their normal operation, will consume engine oil at a higher rate than a naturally aspirated engine (non-turbocharged engine). In this case, a "turbocharged" engine could require topping up of the engine oil more frequently.
1101132018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. MService Action: Replace the Coolant Pump. Coolant is leaking from the coolant pump. CAUSE The coolant pump may develop cracks in the plastic housing. These cracks may result in a coolant leak.
B1101172018-11-26. Service bulletin. ENGINE. N63T AND S63T ENGINE: VALVE SEAL REPLACEMENT. This SI provides a new tool and a new procedure for the N63TU valve seals replacement. Please refer to the following applicable SIBs before replacing the valve seals. SI B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs SI B11 01 13 - N63 and N63TU Engines: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity SI B11 03 13 - Engine Oil Consumption (all models) SI B11 04 13 - N63TU Engine: Engine Oil Consumption If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil
6206132018-11-13. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE. Condition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster.
1307122018-11-13. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
1307122018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: ? During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ? During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated.? While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. ? Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
1107132018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. The test plan will help identify the actual oil level, and advise the amount that will need to be added to correctly fill the engine when topping up. When performing the scheduled oil service and filling the engine with the amount specified, the applicable ISTA/D repair instruction does not require performing this test plan. Applicable models: ? F01 and F02 with the N63T engine with I-Level F001-13-03-501 or higher ? F06, F07, F12 and F13 with the N63T engine with I-Level F001-13-03-501 or higher ? F10 with the N63T engine with I-Level F010-13-07-501 or higher ? F15 and F16 with all I-LevelsTest plan path: 1. Select "Service Function." 2. Select "Drive." 3. Select "Motor Electronics." 4. Select "Motor Oil."5. Select "Oil Level." 6. Select "Continue." 7. Follow the steps as directed in the test plan to complete the measurement. Always refer to ISTA/D for the recommended oil type and the amount required, using the VIN number of the vehicle. IMPORTANT: Do not perform this test plan on the following vehicles: ? Performing the test plan on any vehicle with the N63 engine will result in an inaccurate measurement. ? Performing this test plan on any vehicle with the N63T engine without the applicable I-Levels stated above will result in an inaccurate measurement. Do not perform this test plan when performing engine oil services. Fill the engine with the specification found in ISTA/D. WARRANTY INFORMATION Not applicable. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20361.1.B110713....1/2/2015
1304132018-11-13. Service bulletin. ENGINE. N55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION There is an error in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. The vehicle may also exhibit rough running at idle and while driving. F07 and F10: P/N 13 64 7 639 994 is for all vehicles produced from 7/2014 P/N 13 64 7 597 870 is for all vehicles produced from 1/2011 to 7/2014 P/N 13 53 7 568 607 is for all vehicles produced to 1/2011 F06, F12 and F13: P/N 13 64 7 597 870 is for all vehicles produced from 1/2011 P/N 13 53 7 568 607 is for all vehicles produced to 1/2011 Until further notice, it is good practice to verify that the injector part number being removed from the engine matches the new injector part number. Always review the vehicle history to identify if the injectors have already been replaced. When the ETK data is corrected, a notification will be distributed. WARRANTY INFORMATION Not applicable. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16028.3.B130413... 4/24/2014
B1216152018-11-13. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. N63T: Oxygen Sensor Internal Resistance Faults. The Service Engine Soon light comes on with either or both of the following faults stored in the DME memory: ? 12B701 - Oxygen sensor heating after catalytic converter, function: Internal resistance too high ? 12B801 - Oxygen sensor heating after catalytic converter 2, function: Internal resistance too high The engine operation and performance are not affected. The DME diagnosis for the post catalyst oxygen sensor(s) is too sensitive.
1204152018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE. SUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity.
1102152018-11-13. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV). SUBJECT Deleting DME Adaptations After Crankshaft Sensor-related Repairs. The erroneous misfire faults are stored, and the Service Engine Soon light (MIL) illuminates The ISTA Service Function to delete the DME adaptations fails to clear the crankshaft incremental wheel adaptation, depending on the current DME software version. This adaptation must be cleared whenever the following repairs are made: 1. Replacement of the crankshaft position sensor 2. Replacement of the incremental sensor wheel on the crankshaft 3. Replacement of the crankshaft 4. Replacement of the crankcase (block) with pistons 5. Replacement of the engine assembly Due to slight tolerance differences with the new replacement hardware and the original learned crankshaft position, values could cause cylinder balance calculation errors by the DME. DME software (the incremental wheel adaptation cannot be cleared)
B1210162018-11-13. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. "N63T - Drivetrain Malfunction Message after Driving for Several Hours This Service Information bulletin supersedes SI B12 10 16 dated April 2016. ""Drivetrain Malfunction"" message displayed with reduced engine power. Erroneous misfire faults may be stored for cylinders 3 and 6. The situation is most likely to occur after driving for several hours at constant highway speeds with light throttle (low load and low engine speed). Cycling ignition off and back on again clears the ""Drivetrain Malfunction"" warning DME software (plausibility check error)."

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.