Service bulletin 0500415
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10220431 |
| Published by NHTSA | 2022-09-26 |
| Manufacturer's number | 0500415 |
| Manufacturer's date | 2015-06-10 |
| NHTSA component | WHEELS |
NHTSA's summary
Incorrectly installed front wheel speed sensor wire.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Wheels
| DODGE CHARGER | 2015 |
|---|
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 05154262A | 2022-12-19. Service bulletin. Hub & Bearing Assy - Front For LA, LD SRT vehicles with the 2-piece front brake rotor (BR7 sales code), do NOT replace the front Hub & Bearing Assy for a clicking noise occurring while turning during low speed parking lot maneuvers. Instead, remove front wheels and rotors and clean mating surfaces (wheel mounting face, rotor mounting faces (both sides), and hub face) with a Scotch Brite Pad or equivalent, and re-assemble. |
|---|---|
| 9003418 | 2022-10-24. Service bulletin. Rotor - Front 2 Piece For LA, LD SRT vehicles with the 2-piece Front Rotor (BR7 sales code), do NOT replace the rotor for a clicking noise occurring while turning at low parking lot speeds. Instead, remove front wheels and rotors and clean mating surfaces (wheel mounting face, rotor mounting faces (both sides), and hub mounting face) with a Scotch Brite Pad or equivalent, and reassemble. When installing wheel, MUST use clicker/torque wrench, set to 110 ft-lb (150 Nm). |
| 300122 | 2022-10-17. Service bulletin. Charger Pursuit All Wheel Drive (AWD) Front Halfshafts |
| 23-012-17 REV. A | 2022-08-08. Service bulletin. Wheel Liner Push Pin Fastener Replacement This bulletin involves replacing both wheel liner push pin fasteners at the front fenders. The customer may describe a rattle from the left, right or both, front wheel openings while driving. This condition is caused from one or both plastic front wheel liner fasteners loosening from their locations. |
| 9003655 | 2022-08-08. Service bulletin. Rear Axle Assembly If replacing Limited Spin Differential (LSD)/Anti-Spin Differential rear axles for any reason, the Mopar replacement axle will need the oil drained and re-filled with oil PN: 68083381AA (which contains updated friction modifier). This change was recently introduced in production to help address axle noise concerns being reported from the field while the vehicle is performing tight turning maneuvers. Failure to do so may result in a customer returning with noise complaints. NOTE: If the Mopar replacement axle serial number is past the following dates below for the corresponding axle part numbers, DO NOT DRAIN AND REFILL. The replacement axle will already have new fluid: Axle Part#: 53010668XX ? Serial # T03UG0047EXXXX Axle Part#: 53010669XX ? Serial # T03UG0047GXXXX Axle Part#: 68269917XX ? Serial # T03UG0037JXXXX Axle Part#: 05038703XX ? Serial # T03UG0047HXXXX Otherwise, perform the following repair procedure in the order given: 1. Follow standard rear axle installation procedure. Refer to the detailed service procedures available in DealerCONNECT> TechCONNECT under: Service Info> 03 - Differential and Driveline> Rear Axle> Installation>Standard Procedure>Rear Axle 2. Follow standard axle fluid drain/re-fill service procedure in TECHCONNECT. Refer to the detailed service procedures available in DealerCONNECT> TechCONNECT under: Service Info> 03 - Differential and Driveline> Rear Axle> Standard Procedure>Standard Procedure - Fluid Drain and Fill |
| 05-004-15 | 2021-05-03. Service bulletin. Incorrectly installed front wheel speed sensor wire. |
| 05154262A | 2018-06-11. Service bulletin. Hub & Bearing Assy - Front For LA, LD SRT vehicles with the 2-piece front brake rotor (BR7 sales code), do NOT replace the front Hub & Bearing Assy for a clicking noise occurring while turning during low speed parking lot maneuvers. Instead, remove front wheels and rotors and clean mating surfaces (wheel mounting face, rotor mounting faces (both sides), and hub face) with a Scotch Brite Pad or equivalent, and re-assemble. |
| 23-012-17 REV. A | 2018-06-11. Service bulletin. Wheel Liner Push Pin Fastener Replacement This bulletin involves replacing both wheel liner push pin fasteners at the front fenders. The customer may describe a rattle from the left, right or both, front wheel openings while driving. This condition is caused from one or both plastic front wheel liner fasteners loosening from their locations. |