Service bulletin SSM 48717
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10174405 |
| Published by NHTSA | 2020-05-04 |
| Manufacturer's number | SSM 48717 |
| Manufacturer's date | 2020-04-02 |
| NHTSA component | EQUIPMENT:ELECTRICAL |
NHTSA's summary
Some 2020 F-Super Duty vehicles equipped with the Blind Spot Information System (BLIS) and Cross Traffic Alert (CTA) may require the removal of the factory equipped tail lamps to accommodate the use of aftermarket equipment. Once the tail lamps are removed, this may result in BLIS and CTA warning indicators illuminated in the instrument panel cluster (IPC). To clear these warning indicators, the BLIS and CTA systems will need to be disabled using the FDRS scan tool. Start a vehicle session in FDRS using the vehicles VIN and go to the toolbox tab. The BCM will have an application labeled Disable/Enable Blind Spot Information System. Download and run this application to enable or disable the BLIS And CTA systems.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Equipment and accessories
| FORD F-250 SD | 2020 (the catalog's model; the bulletin names a series or trim of it) |
|---|---|
| FORD F-350 SD | 2020 (the catalog's model; the bulletin names a series or trim of it) |
| FORD F-450 SD | 2020 (the catalog's model; the bulletin names a series or trim of it) |
| FORD F-550 SD | 2020 (the catalog's model; the bulletin names a series or trim of it) |
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 23V420000 | 2023-06-09. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL |
|---|---|
| 21V087000 | 2021-02-18. EQUIPMENT:OTHER:LABELS |
A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.
| SSM 52476 | 2024-05-03. Service bulletin. All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad. |
|---|---|
| 22M03 S1 | 2024-05-02. Service bulletin. Certain 2017-2020 Model Year Continental and Super Duty, 2018-2020 Navigator, 2020 Aviator, and 2020 Explorer Vehicles Replace Front and/or Side Cameras if Foggy |
| TSB 23-2307 | 2023-11-02. Service bulletin. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the SYNC module (APIM) software. |
| SSM 51937 | 2023-10-05. Service bulletin. Some vehicles equipped with power folding mirrors may exhibit power folding mirrors that are inoperative or exhibit a clicking sound. This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization. |
| SAN-Vol1 I1 | 2023-08-16. Service bulletin. The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information. |
| SSM 51829 | 2023-08-14. Service bulletin. Some F-Super Duty and F-150 vehicles equipped with trailer tow mirror may exhibit various exterior rear view mirror functional concerns that require replacement after diagnosis. To properly determine if the defect is warrantable, cleaning and close inspection of the affected mirror may be required. To aid in proper warranty determination, the Rear-View Mirror Analysis general service bulletin (GSB) has been updated with a detailed cleaning procedure that should be followed prior to any inspection. New labor operations (17682ZZ or 17682ZZT) have been created that covers the cleaning and inspection process and may be used even if condition of failure is non-warrantable. Ford has inspected numerous returned parts and determined many cases are caused by damage which is unwarrantable and may be subject to chargeback. Refer to the latest version of the GSB on OASIS. |
| 22M03 | 2023-07-07. Service bulletin. Certain 2017-2020 Model Year Continental and Super Duty, 2018-2020 Navigator, 2020 Aviator, and 2020 Explorer Vehicles Replace Front and/or Side Cameras if Foggy |
| SSM 51648 | 2023-05-31. Service bulletin. Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine may experience a lack of power due to snow packing of the engine air cleaner when operating in extremely snowy conditions. This may also be due to ice forming in the air intake while operating in temperatures below -22°F (-30°C). Diagnostic trouble code (DTC) P1548 may be present in the powertrain control module (PCM). To supplement heavy snow environment pre-filter service kit (service part LC3Z-9K635-AA), a front grill cover (service part NC3Z-19A413-A) is now available for service but is not a warrantable item. It is recommended that the front grill cover be removed at temperatures greater than 10°F (-12°C) and reinstall in subsequent winter seasons in order to maintain optimal vehicle performance. |
| TSB 23-2115 | 2023-05-04. Service bulletin. Some 2015-2020 F-150 and 2017-2022 F-Super Duty vehicles may exhibit a lack of heat or cooling from the cabin vents when the climate control settings are adjusted between hot and cold. This may be due to a stuck/binding temperature door within the climate control housing or binding/inoperative temperature door actuator. Diagnostic trouble code (DTC) B1081:07 may be present in the front controls interface module (FCIM) or heating ventilation and air conditioning (HVAC) module. To correct the condition, follow the Service Procedure to remove the climate control housing and replace the temperature door cam(s), lubricate the temperature blend door bearing surface, and apply flock tape to actuator to seal out debris. |
| SSM 51449 | 2023-04-05. Service bulletin. Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPass®/LincolnWay® app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |