WenmarOpen by Wenmar Pro

Service bulletin ITB19-024

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10165750
Published by NHTSA2019-10-08
Manufacturer's numberITB19-024
Manufacturer's date2019-09-12
NHTSA componentSEATS; ELECTRICAL SYSTEM; AIR BAGS

NHTSA's summary

DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed And The following screen will display: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. • Refer to SERVICE PROCEDURE on the next page. HINT: “OCS” may also be referred to as “ODS”. 2. Perform “75-zero RESET”.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Air bags, Electrical system, Seats

Trouble codes named

B00A0

Vehicles listed
INFINITI FX502009, 2010, 2011, 2012, 2013
INFINITI JX352013
INFINITI Q502014, 2015, 2016, 2017, 2018, 2019
INFINITI Q50 HYBRID2014, 2015, 2016, 2017, 2018 (the catalog's model; the bulletin names a series or trim of it)
INFINITI Q602017, 2018, 2019
INFINITI QX502019, 2020
INFINITI QX562011, 2012, 2013
INFINITI QX602014, 2015, 2016, 2017, 2018, 2019, 2020
INFINITI QX60 HYBRID2014, 2015, 2016, 2017 (the catalog's model; the bulletin names a series or trim of it)
INFINITI QX702014, 2015, 2016, 2017
INFINITI QX802014, 2015, 2016, 2017, 2018, 2019
INFINITI redundant Q502020

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
20201362020-03-31. Airbag
20V1880002020-03-30. AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE
20184802018-09-07. Airbag
18V5930002018-09-06. AIR BAGS:KNEE BOLSTER
20174472017-09-15. Airbag
17V5710002017-09-15. AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE
17V4760002017-07-27. ELECTRICAL SYSTEM:SOFTWARE; FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP
16V2440002016-04-26. AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION
20161792016-04-25. Seats And Restraints
20161232016-03-17. Airbag

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
ITB22-025D2026-08-28. Service bulletin. ROARING NOISE FROM THE ENGINE COOLING FAN ASSEMBLY AND THE A/C IS NOT COOLING IF YOU CONFIRM A roaring noise from the engine cooling fan assembly (engine fan on high not cycling) is present, and the Air Conditioning (A/C) is not cooling. ACTION 1. Check the hardware part number for the IPDM E/R. 2. Replace the IPDM E/R with the part number listed in the PARTS INFORMATION, if applicable. 3. Reconfigure the IPDM E/R, if applicable. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
ITB12-011R2026-04-29. Service bulletin. TELEMATICS SERVICE INFORMATION See ITB19-029 for models built after those listed above for a different Service Procedure. SERVICE INFORMATION The Applied Vehicles are equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active Infiniti Connection® or Infiniti InTouch Services™, the TCU communicates with the Infiniti Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the Applied Vehicles. Ø A table has been provided on the next page that lists the model and year specific steps required to successfully configure a TCU after it has been replaced. Ø A check OFF sheet has been provided on page 21 to print and check off steps as they are performed. Please staple the completed Check OFF Sheet to the repair order.
ITB23-023A2025-02-25. Service bulletin. AEB WARNING LIGHT IS ON WITH WARNING MESSAGES DISPLAYED ON COMBINATION METER APPLIED VEHICLES: 2015-2024 Q50 (V37) 2015-2018 Q50 Hybrid (HV37) 2017-2022 Q60 (CV37) 2015-2019 Q70 (Y51) 2015-2018 Q70 Hybrid (HY51) 2019-2024 QX50 (J55) 2022-2024 QX55 (FJ55) 2015-2021 QX60 (L50) 2022-2024 QX60 (L51) 2015-2019 QX60 Hybrid (L50H) 2015-2024 QX80 (Z62) SERVICE INFORMATION The AEB system is designed to turn itself OFF during driving conditions (e.g., rain, snow, fog, etc.) that obstruct its sensors. This behavior is normal, and no repairs should be performed. When the AEB system performs an intentional shutdown, the customer may state the following: • The ICC stopped working while driving, • The AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), • The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND • DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
ITB17-050C2025-02-10. Service bulletin. MIL ON WITH DTC(S) STORED IN THE ECM This bulletin is no longer active. Please discard previous versions of ITB17-050.
ITB24-017A2025-01-30. Service bulletin. ENGINE ROOM SUB-HARNESS IF YOU CONFIRM DTC P06DA-00 for “ENGINE OIL PRESSURE CONTROL” is stored as current (active) with CONSULT-III plus (C-III plus). ACTION Replace the engine room sub-harness. Refer to the SERVICE PROCEDURE in this bulletin. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
ITB19-024D2024-10-22. Service bulletin. DTC B00A0-00 STOREIF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)D
ITB22-020B2024-09-04. Service bulletin. TELEMATICS CONTROL UNIT RESET AFTER AUTOMATIC COLLISION NOTIFICATION SERVICE INFORMATION The Telematics Control Unit (TCU) has the ability to send an automatic collision notification when the vehicle is involved in an accident. Once an automatic collision notification is performed, the function becomes disabled and the TCU must be reset to re-enable the automatic collision notification function. Some models will store DTC B2E1B-97 for “Automatic eCAll locked” as “CURRENT” when this function is disabled. This bulletin describes how to reset the TCU after an automatic collision notification has been performed. For models with B2E1B-97 for “Automatic eCAll locked” set as “CURRENT”, complete the SERVICE PROCEDURE starting on page 2, and then erase DTCs after confirming the TCU condition is “UNLOCK”.
ITB22-017B2024-09-04. Service bulletin. DTC B2E01-96 (INTERNAL BATTERY) STORED AS CURRENT IN IVC APPLIED SYSTEMS: Vehicles equipped with Telematics SERVICE INFORMATION CONSULT has been updated to allow DTC B2E01-96 for “Internal battery” to be cleared in the Telematics Control Unit (TCU). If DTC B2E01-96 is Current/Active in the TCU, and no additional Current/Active DTCs are present in the TCU, perform the SERVICE PROCEDURE starting on page 2. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-042E2024-09-04. Service bulletin. AV CONTROL UNIT REPLACEMENT PROCESS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM The AV control unit needs to be replaced. ACTION 1. Read and save the VIN. 2. Read and save the configuration. 3. Replace the AV control unit. 4. Reprogram the AV control unit. 5. Configure the AV control unit. 6. Write the VIN to the AV control unit. IMPORTANT: Procedures 4-6 above must be performed in the order shown below. ORDER OF COMPLETION REPROGRAM AV Control Unit CONFIGURE AV Control Unit WRITE VIN to AV Control Unit Infiniti
ITB19-029E2024-09-04. Service bulletin. TELEMATICS (IVC) SERVICE INFORMATION Vehicles equipped with factory telematics system HINT: • If the client experiences Wi-Fi hotspot related concerns only, DO NOT replace the TCU. Have the client contact the AT&T Support line at 1 (888) 719-7242. • See ITB12-011 for models built before those listed above. SERVICE INFORMATION The APPLIED VEHICLES are equipped with a wireless communication device called a Telematics Communication Unit (TCU). The TCU communicates with the Infiniti Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the APPLIED VEHICLES. • An Order of Completion table has been provided on the next page that lists the steps required to successfully configure a TCU after it has been replaced. • A CHECK-OFF SHEET has been provided on page 16. Print and check off steps as they are completed. Staple the completed CHECK-OFF SHEET to the repair order.