Transport Canada recall 2016179
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2016179 |
| Reported | 2016-04-25 |
| Component | Seats And Restraints |
| Notification type | Safety Mfr |
| Units potentially affected | 257130 |
What is wrong
On certain vehicles, a defect in the occupant classification system could allow an adult sitting in the front passenger seat to be classified as a child or an “empty seat”. This would suppress the airbag, which could increase the risk of injury in a crash. Correction: For affected Altima, Maxima, Murano, Rogue and Sentra vehicles, dealers will reprogram the airbag control unit and the occupant classification system control unit. For affected Leaf, NV200, Pathfinder, Q50 and JX35/QX60 vehicles, dealers will replace the occupant classification system electronic control unit.
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| NTB19-071C | 2023-04-10. Service bulletin. DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
|---|---|
| NTB21-077 | 2022-01-08. Service bulletin. DRIVERS POWER SEAT IS INOPERATIVE IF YOU CONFIRM The customer states that one or more of the driver (LH) seat controls are (or were) inoperative, AND/OR The windows, sunroof, sunshade and power mirrors are (or were) inoperative. NOTE: A no start condition may also be present. ACTION Follow the SERVICE PROCEDURE in this bulletin to: 1. Inspect the power seat switch wiring harness for damage. 2. Repair any damage found. 3. Install the rubber grommet listed in PARTS INFORMATION. |
| PC835 - R1606 Ca | 2021-10-07. Service bulletin. R1606 Occupant Classification System (OCS) Campaign Quality Review ***** Retailer Announcement ***** INFINITI is committed to the safety, security and satisfaction of our clients and is conducting a quality review of specific repairs for a previously completed campaign (R1606). If the VIN displays QA campaign ID PC835, retailers should perform the procedure attached to this communication even if the National Service History indicates the remedy action was previously performed for the vehicle. VINs identified with this QA campaign ID are being inspected to ensure the recall remedy was performed and documented in accordance with INFINITI’s quality standards. ***** What Retailers Should Do ***** PLEASE FOLLOW THE ATTACHED PROCEDURE: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History – Open Campaigns I.D. PC835. 2. Retailers should complete this action on both retailed vehicles and previously owned vehicles within retailer inventory. • Retailers should follow all stop sale and do not drive, loan, sell, or trade instructions for campaigns. 3. Retailers will need to file the appropriate claim using applicable Op Code information in the repair procedure attached to this announcement to close the campaign. NOTE: Parts replaced under this activity will be placed on parts return. Monitor the Warranty Parts Return Website located at NNAnet.com for notifications. |
| NTB16-034 | 2021-05-24. Service bulletin. 2015 Mur ano; Buzz noise from seat with seat climate cointrol heater turned on |
| NTB16034 | 2021-05-10. Service bulletin. IF YOU CONFIRM A buzz noise coming from: - The driver seat when the driver seat climate control heater is turned ON. and/or - The passenger seat when the passenger seat climate control heater is turned ON. ACTION Replace the climate controlled seat control unit. - Replace the control unit only for the seat that is making the buzz noise. - Refer to the Electronic Service Manual (ESM), section SE-Seat, for replacement information. See this bulletin for further information. |
| ITB14059A | 2021-05-10. Service bulletin. IF YOU CONFIRM All "hands free" functions of the Intelligent Key (I-Key) do not work. For example, the doors will not lock or unlock when pressing either front door request switch. NOTE: - The issue of all I-Key "hands free" functions not working may occur intermittently or all the time. - The message "No Key Detected" or similar may show on the Vehicle Information Display (located in the combination meter). - All I-Key remote button functions (door lock/unlock, etc.) WILL work normally when all I-Key "hands free" functions are NOT working. ACTION 1. Inspect the I-Key?s battery on its negative contact side. 2. If excessive scratching is found, replace the battery. 3. Verify all I-Key functions (both "hands free" and remote) work properly after battery replacement. NOTE: Do NOT replace the BCM, I-Key, or other parts for the issue described under IF YOU CONFIRM, if it should occur. See this bulletin for further detail. |
| NTB14114A | 2021-05-10. Service bulletin. IF YOU CONFIRM All "hands free" functions of the Intelligent Key (I-Key) do not work. For example, the doors will not lock or unlock when pressing either front door request switch. NOTE: - The issue of all I-Key "hands free" functions not working may occur intermittently or all the time. - The message "No Key Detected" or similar may show on the Vehicle Information Display (located in the combination meter). - All I-Key remote button functions (door lock/unlock, etc.) WILL work normally when all I-Key "hands free" functions are NOT working. ACTION 1. Inspect the I-Key?s battery on its negative contact side. 2. If excessive scratching is found, replace the battery. 3. Verify all I-Key functions (both "hands free" and remote) work properly after battery replacement. NOTE: Do NOT replace the BCM, I-Key, or other parts for the issue described under IF YOU CONFIRM, if it should occur. See this bulletin for further detail. |
| NTB15088 | 2021-05-10. Service bulletin. SERVICE INFORMATION If you confirm there is a need to replace the slide window "INFORMATION" label on an Applied Vehicle for any reason (scratches, worn appearance, etc.): - Do not replace the slide window latch finisher. The "INFORMATION" label is available as a separate service part. - Follow the procedure on page 2 when replacing the label. See this bulletin for further detail. |
| NTB15042A | 2021-05-10. Service bulletin. SERVICE INFORMATION If the A/C compressor on an Applied Vehicle is being replaced for any reason, perform the following: 1. Evacuate the system?s refrigerant. 2. Record the amount evacuated (this will determine if step 4 applies). NOTE: Make sure your Robinair/Tech-Mate Air-Conditioning Machine # 48710 is calibrated. 3. Replace the compressor with the one listed in FAST or your electronic parts catalog. - Refer to the applicable Electronic Service Manual (ESM), section HAC-Heater & Air Conditioning System, for compressor removal and installation procedure. 4. If the amount initially evacuated was less than 600 grams (1.32 pounds), check for leaks and repair as needed. 5. Evacuate and charge the A/C system. - Ideal refrigerant charge amount: 700 grams (1.54 pounds) - Acceptable charge amount: 700 grams +/- 50 grams (1.54 pounds +/- 0.11 pounds) NOTE: Do not use the charge capacity value listed in NV200 Taxi ESMs. See this bulletin. |
| NTB14069B | 2021-05-10. Service bulletin. IF YOU CONFIRM: The sunshade fabric catches in its tracks and/or the sunshade keeper (front bar) is hanging down. ACTION: Replace the sunshade assembly. - Install a plastic retainer clip on the one end of the sunshade. - Refer to this bulletin?s SERVICE PROCEDURE for sunshade removal and installation. See this bulletin for further detail. |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.