Service bulletin 05002
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10015075 |
| Published by NHTSA | 2005-05-18 |
| Manufacturer's number | 05002 |
| Manufacturer's date | 2005-04-28 |
| NHTSA component | ENGINE AND ENGINE COOLING |
NHTSA's summary
NEW WATER PUMP FOR 3.7L ENGINE - NO LONGER COMMON WITH 4.7L. ADVANCED SERVICE INFORMATION #05-002. *TT
The document
No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.
Components
Engine
| DODGE DAKOTA | 2004, 2005 |
|---|---|
| DODGE DURANGO | 2004, 2005 |
| DODGE RAM | 2002, 2003, 2004 |
| DODGE RAM 1500 | 2002, 2003, 2004 (the catalog's model; the bulletin names a series or trim of it) |
| DODGE RAM 2500 | 2002, 2003, 2004 (the catalog's model; the bulletin names a series or trim of it) |
| DODGE RAM 3500 | 2003, 2004 (the catalog's model; the bulletin names a series or trim of it) |
| JEEP GRAND CHEROKEE | 2002, 2003, 2004, 2005 |
| JEEP LIBERTY | 2002, 2003, 2004, 2005 |
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 06V199000 | 2006-06-08. ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN |
|---|---|
| 04V337000 | 2004-07-08. ENGINE AND ENGINE COOLING |
| 2002074 | 2002-04-17. Engine |
| 01V348000 | 2001-11-13. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL |
A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.
| 9003215 | 2023-01-09. Service bulletin. Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine. |
|---|---|
| 05191925A | 2022-12-19. Service bulletin. Radiator If vehicle comes in for transmission fluid leaking from trans-oil cooler fittings on the radiator, please perform the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Remove hex nut and the top flared fitting on the radiator tank.~ 3. Using a wire brush and gasket remover, clean off the old sealant on the smaller threaded portion of the flared fitting. Do the same for the threads on the trans oil cooler.~ 4. Apply a new application of Mopar PN 04318032 to the flared fitting, leaving the first threads free for ease of engagement.~ 5. Install the top flared fitting by hand, then torque the fitting to 235 +/- 15 Lb-In.~ 6. Install the hex nut and torque to 100 +/- 10 Lb-In.~ 7. Repeat steps 2-6 for bottom flared fitting.~ 8. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~ |
| 68332810 | 2022-10-17. Service bulletin. Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar® Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 N·m [21 ft. lbs.]. |
| 9003215 | 2022-10-17. Service bulletin. Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine. |
| 9002887 | 2022-10-17. Service bulletin. Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years. |
| 9004350 | 2022-09-26. Service bulletin. GEAR MOTOR, Transfer Case The gear motor assembly is shipped in AWD/2WD position. The transfer case needs to be positioned in AWD/2WD position to properly assemble gear motor to T-Case. Please reference Star Online publication S2121000003 for further details. Do not have the transfer case in in another position other than AWD/2WD and rotate the motor to align the bolt holes as this could result in damage to the gear motor. |
| R2118796A | 2021-05-03. Service bulletin. Valve Body. These may cause over drive cycling. |
| 68332810A | 2021-05-03. Service bulletin. Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. |
| 9004350 | 2021-04-26. Service bulletin. GEAR MOTOR, Transfer Case The gear motor assembly is shipped in AWD/2WD position. The transfer case needs to be positioned in AWD/2WD position to properly assemble gear motor to T-Case. Please reference Star Online publication S2121000003 for further details. Do not have the transfer case in in another position other than AWD/2WD and rotate the motor to align the bolt holes as this could result in damage to the gear motor. |
| 05191925A$ | 2020-10-26. Service bulletin. Radiator If vehicle comes in for transmission fluid leaking from trans-oil cooler fittings on the radiator, please perform the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Remove hex nut and the top flared fitting on the radiator tank.~ 3. Using a wire brush and gasket remover, clean off the old sealant on the smaller threaded portion of the flared fitting. Do the same for the threads on the trans oil cooler.~ 4. Apply a new application of Mopar PN 04318032 to the flared fitting, leaving the first threads free for ease of engagement.~ 5. Install the top flared fitting by hand, then torque the fitting to 235 +/- 15 Lb-In.~ 6. Install the hex nut and torque to 100 +/- 10 Lb-In.~ 7. Repeat steps 2-6 for bottom flared fitting.~ 8. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~ |