Transport Canada recall 2014582
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2014582 |
| Manufacturer's number | P77 |
| Reported | 2014-12-19 |
| Component | Powertrain |
| Notification type | Safety Mfr |
| Units potentially affected | 21779 |
What is wrong
On certain vehicles, the rear axle pinion nut could loosen and allow the rear driveshaft to detach from the axle, or fully detach from the vehicle. Pinion nut separation could also cause the rear axle differential to fail suddenly, causing rear wheel lockup. These issues could result in loss of propulsion, danger to other road users, loss of vehicle control and possible crash causing property damage and/or personal injury. Correction: Dealers will install a pinion nut retainer.
| 2005 DODGE RAM |
|---|
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| 101232 | 2024-11-07. Service bulletin. Plate - Planetary |
|---|---|
| 9004009 | 2022-09-26. Service bulletin. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. |
| 9004009 | 2022-09-26. Service bulletin. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. |
| 9001784 | 2022-09-26. Service bulletin. Mechanical rocker arm, intake, 1.7 ratio. |
| 18-042-14 | 2022-08-15. Service bulletin. Generic Powertrain Control Module (PCM) Procedure This bulletin involves programming a generic PCM with software. |
| DOR-S4W3P-11 | 2018-11-19. Service bulletin. This SKU is an Automatic Transmission Oil Cooler Line. The Customer communication requested return of unsold inventory to inspect for improperly crimped hose fittings. Improperly crimped hose fittings could cause a potential fluid leak at the crimp. |
| DOR-V6G8D-11 | 2018-11-19. Service bulletin. This SKU is an Automatic Transmission Oil Cooler Line. The Customer communication requested return of unsold inventory to inspect the hose end fittings. Parts will be inspected for incorrectly threaded fittings causing inability to complete assembly of the oil cooler line to the vehicle. |
| 2100907 | 2007-06-28. Service bulletin. 1-2 SHIFT HUNT AT LIGHT THROTTLE. *KB |
| 1802907 | 2007-06-15. Service bulletin. GENERIC POWERTRAIN CONTROL MODULE (PCM) PROCEDURE. *KB |
| 2100607 | 2007-04-25. Service bulletin. NEW 48RE FEATURE THAT ALLOWS NORMAL SHIFT SCHEDULE WITH FULL DISABLE OF 4TH GEAR OVERDRIVE. *KB |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.