WenmarOpen by Wenmar Pro

Service bulletins for the 2011 Volkswagen Jetta

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1332 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
TT1313012023-07-10. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. CBFA 2.0T TSI Engine
TT011401a2023-07-10. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Install a vacuum gauge on the dipstick tube and check crankcase vacuum at idle. Compare to a known good vehicle. If the vacuum reading is lower than the comparison vehicle, visually inspect for oil leaks between the engine and the transmission. Smoke test the crankcase by connecting the EVAP smoke machine to the dipstick tube and inspect for leaks at the rear main seal (this will limit pressure to 2 PSI). DO NOT apply shop air to the dipstick tube or the crankcase. If a rear main seal leak is identified, replace the seal. Once replaced, recheck crankcase vacuum at idle. If low, check for additional oil leaks and verify crankcase breather operation (repairing as necessary). Erase the faults and road test 10 miles to recheck operation.
TT0114012023-07-10. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Install a vacuum gauge on the dipstick tube and check crankcase vacuum at idle. Compare to a known good vehicle. If the vacuum reading is lower than the comparison vehicle, visually inspect for oil leaks between the engine and the transmission. Smoke test the crankcase by connecting the EVAP smoke machine to the dipstick tube and inspect for leaks at the rear main seal (this will limit pressure to 2 PSI). DO NOT apply shop air to the dipstick tube or the crankcase. If a rear main seal leak is identified, replace the seal.
TT0014032023-07-10. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL:INFOTAINMENT:BLUETOOTH/WIFI; ELECTRICAL SYSTEM. When performing SVM updates, the scan tool should be hardwired to the vehicle and the Bluetooth physically turned off. A hard wired internet connection is also recommended.
TT0014022023-07-10. Service bulletin. FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM; FUEL SYSTEM, GASOLINE:DELIVERY. When replacing or adapting fuel injectors, if there is no Guided Functions Test Plan, utilize the following
TT001304A2023-07-10. Service bulletin. EQUIPMENT. If a needed service part is on back order, upgrade the daily order to a red order and check the ?Car Down? box to escalate the order. If parts assistance is needed, please call 800-767-6552 to speak with a VWGoA Parts Specialist.
TT0013042023-07-10. Service bulletin. EQUIPMENT. If a needed service part is on back order, upgrade the daily order to a red order and check the ?Car Down? box to escalate the order. If parts assistance is needed, please call 800-767-6552 to speak with a VWGoA Parts Specialist.
VOS-23-212023-07-10. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This communication is a notice for software changes with the ODIS program for specific cars.
V3718022033975112023-07-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. Automatic Transmission Fluid Requirements
V2719012011894_22023-07-10. Service bulletin. ELECTRICAL SYSTEM. Battery Testing and Charging using Midtronics VAS6161 and or GRX3000 Vas Charger
V1719012012855632023-07-10. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Volkswagen Engine Oil Standards, updated to include model year 2024.
V1718062017813182023-07-10. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Engine Oil Consumption Measurement Instruction and Work sheet.
V0118122014603192023-07-10. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Software Version Management (SVM) instruction.
V0116152014815172023-07-10. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE; ENGINE AND ENGINE COOLING. Gasoline quality information in regards to gasoline engine performance.
V0017132033846192023-07-10. Service bulletin. FUEL SYSTEM, GASOLINE. Gasoline fuel additive
V0116132033805_82023-07-10. Service bulletin. ENGINE AND ENGINE COOLING. Diagnostic Aid for engine misfire.
VOS-23-142023-07-10. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:SOFTWARE. This communication is a notice for software changes with the ODIS program for specific cars
TT45061222023-07-05. Service bulletin. WHEELS; SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING; SERVICE BRAKES, HYDRAULIC. Use the following procedure to diagnose active wheel speed sensor complaints:
TT4411012023-07-05. Service bulletin. ELECTRICAL SYSTEM. If the battery has a low state of charge or is disconnected, fault code 02757 ?adapting tire pressures? may set in address 03 ? Brake Electronics. The GFF test plan for this fault may prove inconclusive and the fault may not clear, even after performing TPMS reset using the button in glove box or through the MFI.
TT4410012023-07-05. Service bulletin. TIRES; TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS. The TPMS system on the MY vehicles listed above, is now an indirect type system. There are no sensors in the wheels as on previous models. There is no separate TPMS module, as all functions are part of the ABS module and monitored through the ABS sensors. For more information on the system, see the May edition of Tech Talk on VwWebsource
TT3214012023-07-05. Service bulletin. POWER TRAIN. Incorrect torque converter or flywheel/flexplate installation can result in transmission damage. When installing an engine, flywheel or transmission, please follow the installation procedures outlined in ELSA. For the flywheel/flexplate, please be certain the correct shim is installed between it and the crankshaft (reference VWIQ120). When installing a torque converter, press the torque converter hub through the seal as far as the first stop. Turn the torque converter while pushing toward the transmission using light force, until the cut outs in the torque converter hub lock into the pump wheel plate. The torque converter slides in. The torque converter is installed correctly if it is easy to turn by hand and if it fits evenly in the transmission bell housing. Additionally, it should spin freely when the transmission bell housing bolts are torqued to the engine block, prior to installation of the flywheel to converter bolts (reference VWIQ121).
TT2713012023-07-05. Service bulletin. ELECTRICAL SYSTEM. When diagnosing a generator charging concern, it is recommended to verify operation of the one way clutch located in the generator pulley (if equipped) before replacing generator assembly. To check the one way clutch, remove the belt from the generator pulley and use a trim removal tool to hold fan blades inside generator, as shown below. When attempting to turn pulley by hand with fan blades held, pulley should spin freely in only one direction. If pulley spins freely in both directions, the one way clutch has failed and should be replaced before continuing diagnosis.
TT2711022023-07-05. Service bulletin. ELECTRICAL SYSTEM. When diagnosing a low battery or no charging system concern, start by inspecting the SA1 200 amp fuse in the SA fuse block. DO NOT replace the generator. Perform a voltage drop test between threaded connections 508 and SA1 as shown in Figure 1. If the voltage drop is above .02V, disconnect the battery and remove the cables at the 508 connection and the SA1 connection. Check for continuity of the threaded plate connection between 508 and SA1. If fuse SA1 is found to have an open circuit, replace the fuse and check the threaded connections closely.
TT2614022023-07-05. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM); ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Disconnect both O2 sensors (front and rear), start engine and let idle. Check MVB's 41/4 and 136/4 and verify have both changed from a 1 to a 0 (you may have to drive the car 4 miles to get them to reset to 0). Also a key cycle may be required for values to reset. This forces the ECM to re-learn the O2 sensor adaptation. Once MVB 41/4 and 136/4 read 0, re-connect the O2 sensors, road test and recheck for faults.
TT2613032023-07-05. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Use of aftermarket air filters such as cotton bed steel mesh or cone style, can cause the MAF sensor to not read accurately, affecting vehicle performance and critical monitoring functions for the diesel particulate filter. This can also result in premature DPF failure. Only use factory air filters. The use of aftermarket air filters is not supported as the system was designed and calibrated to work with factory air filters.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.