WenmarOpen by Wenmar Pro

Service bulletins for the 2026 Ram 5500

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

182 on file from NHTSA, as of 2026-10-19.

About P0072 on the 2026 Ram 5500: what the code means, and the bulletins and recalls about the same components.

By type

By component

By trouble code

Only bulletins with trouble code: P0072 are shown. Show all

Bulletins, newest first
18-044-262026-03-25. Service bulletin. ENGINE. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) ● P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) ● P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) ● P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) ● P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) ● P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** ● P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** ● P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: ● **Oil Level High Warning in the Instrument Panel Cluster (IPC).** ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi
18-012-26 REV.A2026-02-12. Service bulletin. ENGINE; ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. ● P0087-00 - Fuel Rail Pressure Too Low. ● P2540-00 - Low Pressure Fuel System Sensor Circuit Range/Performance. ● P2543-00 - Low Pressure Fuel System Sensor Circuit Intermittent. ● P20EE-00 - SCR Nox Catalyst Efficiency Below Threshold - Bank 1 Catalyst 1. ● P203F-00 - Reductant Level Too Low. ● P2698-00 - Exhaust Aftertreatment Fuel Injector "A" Performance. ● P06B9-00 - Cylinder 1 Glow Plug Circuit Performance. ● P06BA-00 - Cylinder 2 Glow Plug Circuit Performance. ● P06BB-00 - Cylinder 3 Glow Plug Circuit Performance. ● P06BC-00 - Cylinder 4 Glow Plug Circuit Performance. ● P06BD-00 - Cylinder 5 Glow Plug Circuit Performance. ● P06BE-00 - Cylinder 6 Glow Plug Circuit Performance. Customers may also comment on one or more of the following: ● Diesel Exhaust Fluid (DEF) level gauge inaccuracy. ● Poor cold start performance. ● Unable to initiate manual Diesel Particulate Filter (DPF) regen through Electronic Vehicle Information Center (EVIC). ● While using the remote Power Take-Off (PTO) feature, the PTO may not engage or resume operation properly, after disengaging: 1. Engine is running with PTO engaged. 2. Operator is using the equipment, for example a bucket attachment. 3. Operator gets in position, then uses remote start/stop button to turn truck off while they perform a task. 4. The task is completed, then operator is ready to move the bucket so they use remote start/stop to start the engine. 5. The engine starts but PTO does not automatically re-engage so the equipment doesn’t operate. This bulletin involves inspecting and possibly reprogramming the PCM with the latest available software.
18-012-262026-02-04. Service bulletin. ELECTRICAL SYSTEM. NOte: Revision is being created to correct the Models affected. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. ● P0087-00 - Fuel Rail Pressure Too Low. ● P2540-00 - Low Pressure Fuel System Sensor Circuit Range/Performance. ● P2543-00 - Low Pressure Fuel System Sensor Circuit Intermittent. ● P20EE-00 - SCR Nox Catalyst Efficiency Below Threshold - Bank 1 Catalyst 1. ● P203F-00 - Reductant Level Too Low. ● P2698-00 - Exhaust Aftertreatment Fuel Injector "A" Performance. ● P06B9-00 - Cylinder 1 Glow Plug Circuit Performance. ● P06BA-00 - Cylinder 2 Glow Plug Circuit Performance. ● P06BB-00 - Cylinder 3 Glow Plug Circuit Performance. ● P06BC-00 - Cylinder 4 Glow Plug Circuit Performance. ● P06BD-00 - Cylinder 5 Glow Plug Circuit Performance. ● P06BE-00 - Cylinder 6 Glow Plug Circuit Performance. Customers may also comment on one or more of the following: ● Diesel Exhaust Fluid (DEF) level gauge inaccuracy. ● Poor cold start performance. ● Unable to initiate manual Diesel Particulate Filter (DPF) regen through Electronic Vehicle Information Center (EVIC). ● While using the remote Power Take-Off (PTO) feature, the PTO may not engage or resume operation properly, after disengaging: 1. Engine is running with PTO engaged. 2. Operator is using the equipment, for example a bucket attachment. 3. Operator gets in position, then uses remote start/stop button to turn truck off while they perform a task. 4. The task is completed, then operator is ready to move the bucket so they use remote start/stop to start the engine. 5. The engine starts, but PTO does not automatically re-engage so their equipment doesn’t operate. This bulletin involves inspecting and possibly reprogramming the PCM with the latest available software.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.