WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Ram 3500

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

573 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
25003142022-09-26. Service bulletin. ENGINE. Information: P207F P1C70 And SCR Inducement Strategy
18002142022-09-26. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Flash: Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM/PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. Software To Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For The Following Diagnostic Trouble Codes (DTCs). These DTCs Are Currently Tripped As A One Trip Fault And Should Have Been A Two Trip Fault: ? P0201 - P0206 - FUEL INJECTOR X CIRCUIT/OPEN Fault Codes. ? U110E - LOST AMBIENT TEMPERATURE MESSAGE. ? P049D - EGR CONTROL POSITION EXCEEDED LEARNING LIMIT. Improvements To Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (Mil) Illumination For: ? P0087 - FUEL RAIL PRESSURE TOO LOW. ? P0544 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT - SENSOR 1/1. ? P2281 - AIR LEAK BETWEEN MAF AND THROTTLE BODY. ? P0128 - THERMOSTAT RATIONALITY. In low ambient temperatures. ? U3017 - CONTROL MODULE TIMER/CLOCK PERFORMANCE. ? U1421 - IMPLAUSIBLE IGNITION KEY OFF TIME RECEIVED. ? P202E - (DIESEL EXHAUST FLUID) REDUCTANT INJECTOR PERFORMANCE. ? P20EE - SCR NOx CATALYST EFFICIENCY BELOW THRESHOLD - BANK 1. ? P2002 - DIESEL PARTICULATE FILTER EFFICIENCY BELOW THRESHOLD. ? P0604 - INTERNAL CONTROL MODULE RAM ERROR. This DTC may be caused by enabling the remote throttle feature via the EVIC, and it will be accompanied by a ?service electronic throttle control? message in the EVIC. Other Updates: ? Fuel Filter Minder Calibration Changes ? Cruise control system improvements. ? Improvements in exhaust brake switch operation. ? Charging system improvements for dual alternator applications. ? Various wiTECH data and system test additions and improvements. ? OBD Template changes for P2453. ? Dual Fuel Tank component update. ? Inducement Timer Reset (Feature enable in wiTech). ? PTO Denied Status Message Update. ? PTO Horn Request sen
S1709000010RevB2022-09-26. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR; UNKNOWN OR OTHER. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
90037402022-09-15. Service bulletin. ENGINE AND ENGINE COOLING. Oil Pan 2012-2017 Cummins engines with oil pan leaks, please inspect the shallow area of the oil pan for cracks. If cracks are found, please replace as necessary. Cracks are typically found above the cross member area. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return or email chad.w.eichbrecht@fcagroup.com If you do not receive a response within 15 minutes, please proceed with normal repair.
FCA2022-09-15. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION. Customer satisfaction notification P30 Engine Oil Filter Adapter
68105583A2022-08-22. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:FILTER/SCREEN. Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
90017622022-08-22. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Part Description: Thermostat, Engine Issue Description: Important! There has been an application change to the Cummins turbo diesel thermostat. When replacing a thermostat confirm the correct replacement is choosen.~ 2010, 2011, and 2012 RAM Trucks 2500/3500/4500/5500 engine coolant operating temperature has been increased to 200 degrees requiring thermostat 68067109AA.~ 2009, 2013, and 2014 RAM Trucks 2500/3500/4500/5500 engine coolant operating temperature is 190 degrees requiring thermostat 68005464AA.~ These thermostats are not interchangeable and doing so will result in reduced engine performance.
18079152022-08-22. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM). This bulletin involves selectively erasing and reprogramming the Engine Control Module
0900416REVA2022-08-22. Service bulletin. ENGINE AND ENGINE COOLING. This bulletin involves replacing the engine assembly.
18-096-162022-08-15. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT. Flash: 6.4L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. NOTE: **This bulletin contains optional software update that should only be used in situations where the customer is specifically complaining of a Drone Noise, Shudder, Pulsation, or Vibration under light throttle applications while vehicle is operating in MDS/ECO mode. There will be two separate software options displayed on the wiTECH flash tab. The software file released for this condition contains the verbiage ?OPTIONAL?. The other file is the standard software that does not contain improvements for the Drone/Shudder concern. If for some reason the customer finds this shudder improvement objectionable, the PCM software may be returned/reflashed to the standard version. Both software versions will address the remaining conditions noted in the bulletin. A small number of customers may experience a surge, shudder or pulsation type sensation when driving on smooth road surfaces at highway speeds of 64-129 km/h (40-80 mph).** During normal diagnostics a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) present: · **P0335 - Crankshaft Position Sensor Circuit.** · P0300 - Multiple Cylinder Misfire, cold Idle misfire (DJ,D2 or DD vehicles only). · P030X - Cylinder Misfire (any cylinder). · P04D1 - Cooled EGR Temperature Sensor Circuit High. · P04D0 - Cooled EGR Temperature Sensor Circuit Low. · P2504 - Charging System Output High. · P0441 - Evap Purge System Performance. · P2066 - Fuel Level Sensor 2 Performance. · P0401 - EGR System Performance (DJ/D2 vehicles only). · P2096 - Downstream Fuel Trim System 1 Lean (DD/DP vehicles only). · P2098 - Downstream Fuel Trim System 2 Lean (DD/DP vehicles only). ·
18-028-162022-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; EQUIPMENT. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. NOTE: There will be a choice between 2 calibrations. One for vehicles that utilize an ammonia sensor and one for vehicles that have had the ammonia sensor removed. Be sure to select the correct software based on vehicle configuration. Prevent or reduce Malfunction Indicator Lamp (MIL) illumination when no defect is present for the following Diagnostic Trouble Codes (DTCs). These faults have been changed from a one trip fault to a two trip fault: · P0201 - P0206 - Fuel Injector X Circuit/Open Fault Codes. · P049D - Exhaust Gas Recirculation (EGR) Control Position Exceeding Learning Limit. Improvements to prevent or reduce Malfunction Indicator Lamp (MIL) illumination when no defect is present for: · **P229E - NOx Sensor Circuit - Bank 1 Sensor 2 (For non-ammonia delete systems only). · P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2 (For non-ammonia delete systems only). · P22A7 - NOx Sensor Heater Circuit Performance - Bank 1 Sensor 2 (For non-ammonia delete systems only). · U059F - Invalid Data Received From NOx Sensor "B" (For non-ammonia delete systems only). · P2459 - Diesel Particulate Filter Regeneration Too Frequent. · P218F - Reductant No Flow Detected. · P242F - Diesel Particulate Filter Restriction - Ash Accumulation.** · P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1 (For ammonia delete systems only). · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). · P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. · U110E - Lost Ambient Temperature Message. · U3017 - Control Module Timer/Clock Performance.
18-038-142022-08-15. Service bulletin. ENGINE AND ENGINE COOLING. Engine Shutdown Timer Feature Function Improvement This bulletin involves setting the Engine Auto Shutdown Time Limit in the EVIC.
18-034-14 REV. A2022-08-15. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT; ELECTRICAL SYSTEM. P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit
90036932022-08-08. Service bulletin. ENGINE AND ENGINE COOLING. Gasket, Rocker Cover If you are replacing this gasket for an oil leak, please call Steve Alvarado @ (866) 799-1695 ext: 4720271 to arrange for Fastrac shipper
90037792022-08-08. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:FILTER/SCREEN. Diesel Particulate Filter (DPF) Assembly For Cummins equipped vehicles ONLY: If a customer comes in with a check engine light for P2002 which has led to replacing the DPF, please contact Dean Armstrong at cell (248) 202-8148. Cummins engineering is currently investigating the root cause to this condition. If you do not receive an answer or call back within 15 minutes, proceed with the repair.
18-079-152022-08-08. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM/PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. WARNING:There will be a choice between 2 calibrations. One for vehicles that utilize an ammonia sensor and one for vehicles that have had the ammonia sensor removed. Be sure to select the correct software based on vehicle configuration. Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From A One Trip Fault To A Two Trip Fault: P0201 - P0206 - Fuel Injector X Circuit/Open Fault Codes. P049D - EGR Control Position Exceeding Learning Limit. Improvements To Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect Is Present For: ? P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). ? P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. ? U110E - Lost Ambient Temperature Message. ? U3017 - Control Module Timer/Clock Performance. ? P0087 - Fuel Rail Pressure Too Low. ? P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. ? P2281 - Air Leak Between MAF And Throttle Body. ? P0128 - Thermostat Rationality. In low ambient temperatures. ? U1421 - Implausible Ignition Key Off Time Received. ? P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. ? P20EE - SCR NOX Catalyst Efficiency Below Threshold - Bank 1. ? P2002 - Diesel Particulate Filter Efficiency Below Threshold. ? P0604 - Internal control Module RAM Error. This DTC may be caused by enabling the remote throttle feature via the EVIC, and it will be accompanied by a ?service electronic throttle control? message in the EVIC. ? SCR Efficiency scan tool test improvement.
90037792022-07-25. Service bulletin. FUEL SYSTEM, OTHER:FUEL FILTER; ENGINE AND ENGINE COOLING:ENGINE:DIESEL. Diesel Particulate Filter (DPF) Assembly For Cummins equipped vehicles ONLY: If a customer comes in with a check engine light for P2002 which has led to replacing the DPF, please contact Dean Armstrong at cell (248) 202-8148. Cummins engineering is currently investigating the root cause to this condition. If you do not receive an answer or call back within 15 minutes, proceed with the repair.
68085740A$2022-07-25. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE AND ENGINE COOLING:ENGINE. Part Description: Engine Out NOx Sensor 1/1, System Out NOx Sensor 1/2 Issue Description: If you receive a DJ/D2 with a MIL illumination and DTC P229F, please do not replace any parts at this time. Cummins Engineering is currently investigating the root cause of the concern and is requesting to visit a dealership with this DTC to gather valuable information. Please contact Christine Donegan at (866) 799-1692 ext 1257~ If causal part replacement is the System Out NOx sensor (Bank 1, Sensor 2) PNs 68085740AA, or 68197109AA, please file claim under LOP 250810. If for the Engine Out NOx Sensor (Bank 1, Sensor 1) use LOP 250809.
S1709000010 Rev.2022-07-18. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
18079152022-07-05. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM). This bulletin involves selectively erasing and reprogramming the Engine Control Module
0900416 REV A2022-07-05. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE. This bulletin involves replacing the engine assembly.
S1709000010 RevB2022-05-31. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
FCA2022-04-04. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:FILTER/SCREEN; EQUIPMENT. Customer satisfaction notification P30 Engine Oil Filter Adapter
S1809000007 Rev.2021-04-26. Service bulletin. ENGINE AND ENGINE COOLING. Customer complaint may include engine oil leak/consumption.
S1709000010 Rev.2021-02-16. Service bulletin. ENGINE AND ENGINE COOLING. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.