WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Ram 3500

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

573 on file from NHTSA, as of 2026-10-19.

About P20E8 on the 2014 Ram 3500: what the code means, and the bulletins and recalls about the same components.

By type

By component

By trouble code

Only bulletins with trouble code: P20E8 are shown. Show all

Bulletins, newest first
18054162022-12-19. Service bulletin. BACK OVER PREVENTION; EXTERIOR LIGHTING; SERVICE BRAKES, HYDRAULIC; POWER TRAIN; ELECTRICAL SYSTEM; ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); FUEL SYSTEM, DIESEL; FUEL SYSTEM, GASOLINE. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · **P218F - Reductant No Flow Detected. · P242F - Diesel Particulate Filter Restriction - Ash Accumulation. · P2281 - Air Leak Between MAF And Throttle Body.** · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). · U110E - Lost Ambient Temperature Message. · P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. · P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. · U3017 - Control Module Timer/Clock Performance. · P0087 - Fuel Rail Pressure Too Low. · P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. · P0128 - Thermostat Rationality. In cold ambient temperatures. · P214D - SCR NOx Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. · P24A5 - Exhaust Gas Recirculation (EGR) Cooler Bypass Bank 1 Control Stuck. · P040B - Exhaust Gas Recirculation Temperature Sensor ?A? Circuit Performance. · U1421 - Implausible Ignition Key Off Time Received. · P0420 - Catalyst Efficiency Below Threshold. · P026B - Injection Timing Performance. · P04DB - Crankcase Ventilation System Disconnected. · P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. · P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. · P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. · P2002 - Diesel Particulate Filter Efficiency Below Threshold. · P0604 - Internal Control Module RAM. · P1451 - Diesel Particulate Filter System Performance.
18-028-162022-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; EQUIPMENT. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. NOTE: There will be a choice between 2 calibrations. One for vehicles that utilize an ammonia sensor and one for vehicles that have had the ammonia sensor removed. Be sure to select the correct software based on vehicle configuration. Prevent or reduce Malfunction Indicator Lamp (MIL) illumination when no defect is present for the following Diagnostic Trouble Codes (DTCs). These faults have been changed from a one trip fault to a two trip fault: · P0201 - P0206 - Fuel Injector X Circuit/Open Fault Codes. · P049D - Exhaust Gas Recirculation (EGR) Control Position Exceeding Learning Limit. Improvements to prevent or reduce Malfunction Indicator Lamp (MIL) illumination when no defect is present for: · **P229E - NOx Sensor Circuit - Bank 1 Sensor 2 (For non-ammonia delete systems only). · P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2 (For non-ammonia delete systems only). · P22A7 - NOx Sensor Heater Circuit Performance - Bank 1 Sensor 2 (For non-ammonia delete systems only). · U059F - Invalid Data Received From NOx Sensor "B" (For non-ammonia delete systems only). · P2459 - Diesel Particulate Filter Regeneration Too Frequent. · P218F - Reductant No Flow Detected. · P242F - Diesel Particulate Filter Restriction - Ash Accumulation.** · P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1 (For ammonia delete systems only). · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). · P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. · U110E - Lost Ambient Temperature Message. · U3017 - Control Module Timer/Clock Performance.
18-079-152022-08-08. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM/PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. WARNING:There will be a choice between 2 calibrations. One for vehicles that utilize an ammonia sensor and one for vehicles that have had the ammonia sensor removed. Be sure to select the correct software based on vehicle configuration. Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From A One Trip Fault To A Two Trip Fault: P0201 - P0206 - Fuel Injector X Circuit/Open Fault Codes. P049D - EGR Control Position Exceeding Learning Limit. Improvements To Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect Is Present For: ? P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). ? P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. ? U110E - Lost Ambient Temperature Message. ? U3017 - Control Module Timer/Clock Performance. ? P0087 - Fuel Rail Pressure Too Low. ? P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. ? P2281 - Air Leak Between MAF And Throttle Body. ? P0128 - Thermostat Rationality. In low ambient temperatures. ? U1421 - Implausible Ignition Key Off Time Received. ? P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. ? P20EE - SCR NOX Catalyst Efficiency Below Threshold - Bank 1. ? P2002 - Diesel Particulate Filter Efficiency Below Threshold. ? P0604 - Internal control Module RAM Error. This DTC may be caused by enabling the remote throttle feature via the EVIC, and it will be accompanied by a ?service electronic throttle control? message in the EVIC. ? SCR Efficiency scan tool test improvement.
18-079-152022-07-25. Service bulletin. EXTERIOR LIGHTING; FUEL SYSTEM, DIESEL; ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM/PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. WARNING:There will be a choice between 2 calibrations. One for vehicles that utilize an ammonia sensor and one for vehicles that have had the ammonia sensor removed. Be sure to select the correct software based on vehicle configuration. Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From A One Trip Fault To A Two Trip Fault: P0201 - P0206 - Fuel Injector X Circuit/Open Fault Codes. P049D - EGR Control Position Exceeding Learning Limit. Improvements To Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect Is Present For: ? P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). ? P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. ? U110E - Lost Ambient Temperature Message. ? U3017 - Control Module Timer/Clock Performance. ? P0087 - Fuel Rail Pressure Too Low. ? P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. ? P2281 - Air Leak Between MAF And Throttle Body. ? P0128 - Thermostat Rationality. In low ambient temperatures. ? U1421 - Implausible Ignition Key Off Time Received. ? P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. ? P20EE - SCR NOX Catalyst Efficiency Below Threshold - Bank 1. ? P2002 - Diesel Particulate Filter Efficiency Below Threshold. ? P0604 - Internal control Module RAM Error. This DTC may be caused by enabling the remote throttle feature via the EVIC, and it will be accompanied by a ?service electronic throttle control? message in the EVIC. Other Updates: ? SCR Efficiency scan tool test improvement.
18-054-162020-10-26. Service bulletin. ELECTRICAL SYSTEM; ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); FUEL SYSTEM, DIESEL. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. · **P218F - Reductant No Flow Detected. · P242F - Diesel Particulate Filter Restriction - Ash Accumulation. · P2281 - Air Leak Between MAF And Throttle Body.** · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). · U110E - Lost Ambient Temperature Message. · P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. · P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. · U3017 - Control Module Timer/Clock Performance. · P0087 - Fuel Rail Pressure Too Low. · P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. · P0128 - Thermostat Rationality. In cold ambient temperatures. · P214D - SCR NOx Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. · P24A5 - Exhaust Gas Recirculation (EGR) Cooler Bypass Bank 1 Control Stuck. · P040B - Exhaust Gas Recirculation Temperature Sensor ?A? Circuit Performance. · U1421 - Implausible Ignition Key Off Time Received. · P0420 - Catalyst Efficiency Below Threshold. · P026B - Injection Timing Performance. · P04DB - Crankcase Ventilation System Disconnected. · P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. · P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. · P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. · P2002 - Diesel Particulate Filter Efficiency Below Threshold. · P0604 - Internal Control Module RAM. · P1451 - Diesel Particulate Filter System Performance. In addition to the above symptoms, the following software improvements are also included in this
18-042-202020-06-22. Service bulletin. FUEL SYSTEM, DIESEL; ELECTRICAL SYSTEM; EQUIPMENT; ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:There will be a choice between two calibrations. One for vehicles that utilize an ammonia sensor and one for vehicles that have had the ammonia sensor removed. Be sure to select the correct software based on vehicle configuration.Improvements to prevent or reduce MIL illumination when no defect is present for:P2201 - Aftertreatment Nox Sensor Circuit Performance - Bank 1 Sensor 1(Ammonia delete systems only). P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2. P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1(New Improvements for ammonia delete systems only). P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance(New Improvements for ammonia delete systems only). P218F - Reductant No Flow Detected. P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. U0001 - CAN C Bus. P229E - NOx Sensor Circuit - Bank 1 Sensor 2(Non-ammonia delete systems only). U059F - Invalid Data Received From NOx Sensor "B"(Non-ammonia delete systems only). P22A7 - NOx Sensor Heater Circuit Performance - Bank 1 Sensor 2(Non-ammonia delete systems only). P2459 - Diesel Particulate Filter Regeneration Too Frequent. P242F - Diesel Particulate Filter Restriction - Ash Accumulation. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. U110E - Lost Ambient Temperature Message. U3017 - Control Module Timer/Clock Performance. P0087 - Fuel Rail Pressure Too Low. P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. P2281 - Air Leak Between MAF And Throttle Body.
18-045-15 REV A2019-05-20. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: ? P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). ? U110E - Lost Ambient Temperature Message. ? P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. ? P2281 - Air Leak Between MAF And Throttle Body. ? P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. ? U3017 - Control Module Timer/Clock Performance. ? P0087 - Fuel Rail Pressure Too Low. ? P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. ? P0128 - Thermostat Rationality. In cold ambient temperatures. ? P214D - SCR NOx Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. ? P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. ? P040B - Exhaust Gas Recirculation Temperature Sensor ?A? Circuit Performance. ? U1421 - Implausible Ignition Key Off Time Received. ? P0420 - Catalyst Efficiency Below Threshold. ? P026B - Injection Timing Performance. ? P04DB - Crankcase Ventilation System Disconnected. ? P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. ? P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. ? P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. ? P2002 - Diesel Particulate Filter Efficiency Below Threshold. ? P0604 - Internal Control Module RAM. ? P1451 - Diesel Particulate Filter System Performance. In addition to the above symptoms, the following software improvements are also included in this update: The Following DTCs Have Been Changed From A One Trip Fault To A Two Trip Fault: ? P0201 - P0206 - Fuel injector
18-079-152018-12-17. Service bulletin. EXTERIOR LIGHTING; FUEL SYSTEM, DIESEL; ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; BACK OVER PREVENTION; SERVICE BRAKES, HYDRAULIC. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM/PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. WARNING:There will be a choice between 2 calibrations. One for vehicles that utilize an ammonia sensor and one for vehicles that have had the ammonia sensor removed. Be sure to select the correct software based on vehicle configuration. Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From A One Trip Fault To A Two Trip Fault: P0201 - P0206 - Fuel Injector X Circuit/Open Fault Codes. P049D - EGR Control Position Exceeding Learning Limit. Improvements To Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect Is Present For: ? P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). ? P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. ? U110E - Lost Ambient Temperature Message. ? U3017 - Control Module Timer/Clock Performance. ? P0087 - Fuel Rail Pressure Too Low. ? P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. ? P2281 - Air Leak Between MAF And Throttle Body. ? P0128 - Thermostat Rationality. In low ambient temperatures. ? U1421 - Implausible Ignition Key Off Time Received. ? P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. ? P20EE - SCR NOX Catalyst Efficiency Below Threshold - Bank 1. ? P2002 - Diesel Particulate Filter Efficiency Below Threshold. ? P0604 - Internal control Module RAM Error. This DTC may be caused by enabling the remote throttle feature via the EVIC, and it will be accompanied by a ?service electronic throttle control? message in the EVIC. Other Updates: ? SCR Efficiency scan tool test improvement.
18-054-162018-06-18. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV); ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · **P218F - Reductant No Flow Detected. · P242F - Diesel Particulate Filter Restriction - Ash Accumulation. · P2281 - Air Leak Between MAF And Throttle Body.** · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). · U110E - Lost Ambient Temperature Message. · P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. · P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. · U3017 - Control Module Timer/Clock Performance. · P0087 - Fuel Rail Pressure Too Low. · P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. · P0128 - Thermostat Rationality. In cold ambient temperatures. · P214D - SCR NOx Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. · P24A5 - Exhaust Gas Recirculation (EGR) Cooler Bypass Bank 1 Control Stuck. · P040B - Exhaust Gas Recirculation Temperature Sensor ?A? Circuit Performance. · U1421 - Implausible Ignition Key Off Time Received. · P0420 - Catalyst Efficiency Below Threshold. · P026B - Injection Timing Performance. · P04DB - Crankcase Ventilation System Disconnected. · P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. · P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. · P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. · P2002 - Diesel Particulate Filter Efficiency Below Threshold. · P0604 - Internal Control Module RAM. · P1451 - Diesel Particulate Filter System Performance.
18-028-16 REV. A2018-05-07. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. NOTE: There will be a choice between 2 calibrations. One for vehicles that utilize an ammonia sensor and one for vehicles that have had the ammonia sensor removed. Be sure to select the correct software based on vehicle configuration. Prevent or reduce Malfunction Indicator Lamp (MIL) illumination when no defect is present for the following Diagnostic Trouble Codes (DTCs). These faults have been changed from a one trip fault to a two trip fault: · P0201 - P0206 - Fuel Injector X Circuit/Open Fault Codes. · P049D - Exhaust Gas Recirculation (EGR) Control Position Exceeding Learning Limit. Improvements to prevent or reduce Malfunction Indicator Lamp (MIL) illumination when no defect is present for: · **P229E - NOx Sensor Circuit - Bank 1 Sensor 2 (For non-ammonia delete systems only). · P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2 (For non-ammonia delete systems only). · P22A7 - NOx Sensor Heater Circuit Performance - Bank 1 Sensor 2 (For non-ammonia delete systems only). · U059F - Invalid Data Received From NOx Sensor "B" (For non-ammonia delete systems only). · P2459 - Diesel Particulate Filter Regeneration Too Frequent. · P218F - Reductant No Flow Detected. · P242F - Diesel Particulate Filter Restriction - Ash Accumulation.** · P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1 (For ammonia delete systems only). · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). · P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. · U110E - Lost Ambient Temperature Message. · U3017 - Control Module Timer/Clock Performance.
18-028-16 REV. A2018-02-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. NOTE: There will be a choice between 2 calibrations. One for vehicles that utilize an ammonia sensor and one for vehicles that have had the ammonia sensor removed. Be sure to select the correct software based on vehicle configuration. Prevent or reduce Malfunction Indicator Lamp (MIL) illumination when no defect is present for the following Diagnostic Trouble Codes (DTCs). These faults have been changed from a one trip fault to a two trip fault: · P0201 - P0206 - Fuel Injector X Circuit/Open Fault Codes. · P049D - Exhaust Gas Recirculation (EGR) Control Position Exceeding Learning Limit. Improvements to prevent or reduce Malfunction Indicator Lamp (MIL) illumination when no defect is present for: · **P229E - NOx Sensor Circuit - Bank 1 Sensor 2 (For non-ammonia delete systems only). · P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2 (For non-ammonia delete systems only). · P22A7 - NOx Sensor Heater Circuit Performance - Bank 1 Sensor 2 (For non-ammonia delete systems only). · U059F - Invalid Data Received From NOx Sensor "B" (For non-ammonia delete systems only). · P2459 - Diesel Particulate Filter Regeneration Too Frequent. · P218F - Reductant No Flow Detected. · P242F - Diesel Particulate Filter Restriction - Ash Accumulation.** · P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1 (For ammonia delete systems only). · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). · P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. · U110E - Lost Ambient Temperature Message. · U3017 - Control Module Timer/Clock Performance.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.