WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Ram 3500

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

573 on file from NHTSA, as of 2026-10-19.

About P049D on the 2014 Ram 3500: what the code means, and the bulletins and recalls about the same components.

By type

By component

By trouble code

Only bulletins with trouble code: P049D are shown. Show all

Bulletins, newest first
1805314a2023-01-17. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel. They are as follows:Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From A One Trip Fault To A Two Trip Fault: P0201 - P0206 - Fuel Injector X Circuit Open Fault Codes. U110E - Lost Ambient Temperature Message. P049D - EGR Control Position Exceeding Learning Limit. P226C - Turgocharger Boost Control ?A? Slow Response.The Following DTC Has Been Changed From A Two Trip Fault To One Trip Fault: U1A24 - Lost Communication With Ammonia Sensor.Improvements To Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect Is Present
1805314REVB2022-09-26. Service bulletin. FUEL SYSTEM, DIESEL; POWER TRAIN; BACK OVER PREVENTION; ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; SERVICE BRAKES, HYDRAULIC; EXTERIOR LIGHTING. Flash: 6.7L Diagnostic And System Improvements Bulletin involves reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel. They are as follows:Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From P0201 - P0206 - Fuel Injector X Circuit Open Fault Codes. U110E - Lost Ambient Temperature Message. P049D - EGR Control Position Exceeding Learning Limit. P226C - Turgocharger Boost Control ?A? Slow Response.The Following DTC Has Been Changed From A Two Trip Fault To One Trip Fault: U1A24 - Lost Communication With Ammonia Sensor.Improvements To Prevent/ Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect Is Present For: U3017 - Control Module Timer/Clock Performance. P0087 - Fuel Rail Pressure Too Low. P2281 - Air Leak Between MAF And Throttle Body. P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. P0128 - Thermostat Rationality. In cold ambient temperatures. P214D - SCR NOx Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P040B - Exhaust Gas Recirculation Temperature Sensor ?A? Circuit Performance. U1421 - Implausible Ignition Key Off Time Received. P0420 - Catalyst Efficiency Below Threshold. P026B - Injection Timing Performance. P04DB - Crankcase Ventilation System Disconnected. P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P0604 - Internal Control Module RAM. P1451 - Diesel Particulate Filter System Performance.Other Updates Included: Urea system calibration changes. Fuel Filter Minder Calibrat
1800214REVC2022-09-26. Service bulletin. SERVICE BRAKES, HYDRAULIC; FUEL SYSTEM, GASOLINE; BACK OVER PREVENTION; POWER TRAIN; EXTERIOR LIGHTING; STRUCTURE; ELECTRICAL SYSTEM; FUEL SYSTEM, DIESEL. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM/PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel.Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From A One Trip Fault To A Two Trip Fault: P0201 - P0206 - Fuel Injector X Circuit/Open Fault Codes. U110E - Lost Ambient Temperature Message. P049D - EGR Control Position Exceeding Learning Limit.Improvements To Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect Is Present For: U3017 - Control Module Timer/Clock Performance. P0087 - Fuel Rail Pressure Too Low. P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. P2281 - Air Leak Between MAF And Throttle Body. P0128 - Thermostat Rationality. In low ambient temperatures. U1421 - Implausible Ignition Key Off Time Received. P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. P20EE - SCR NOX Catalyst Efficiency Below Threshold - Bank 1. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P0604 - Internal control Module RAM Error. This DTC may be caused by enabling the remote throttle feature via the EVIC, and it will be accompanied by a ?service electronic throttle control? message in the EVIC.Other Updates: Urea system calibration changes. Fuel Filter Minder Calibration Changes. Cruise control system improvements. Improvements in exhaust brake switch operation. Charging system improvements for dual alternator applications. Various wiTECH data and system test additions and improvements. OBD Template changes for P2453. Dual Fuel Tank component update. Inducement Timer Reset (Feature enable in wiTech). PTO Denied Status Message Update. PTO Horn Request sent to Body Control Unit (BCU.)
18002142022-09-26. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Flash: Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM/PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. Software To Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For The Following Diagnostic Trouble Codes (DTCs). These DTCs Are Currently Tripped As A One Trip Fault And Should Have Been A Two Trip Fault: ? P0201 - P0206 - FUEL INJECTOR X CIRCUIT/OPEN Fault Codes. ? U110E - LOST AMBIENT TEMPERATURE MESSAGE. ? P049D - EGR CONTROL POSITION EXCEEDED LEARNING LIMIT. Improvements To Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (Mil) Illumination For: ? P0087 - FUEL RAIL PRESSURE TOO LOW. ? P0544 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT - SENSOR 1/1. ? P2281 - AIR LEAK BETWEEN MAF AND THROTTLE BODY. ? P0128 - THERMOSTAT RATIONALITY. In low ambient temperatures. ? U3017 - CONTROL MODULE TIMER/CLOCK PERFORMANCE. ? U1421 - IMPLAUSIBLE IGNITION KEY OFF TIME RECEIVED. ? P202E - (DIESEL EXHAUST FLUID) REDUCTANT INJECTOR PERFORMANCE. ? P20EE - SCR NOx CATALYST EFFICIENCY BELOW THRESHOLD - BANK 1. ? P2002 - DIESEL PARTICULATE FILTER EFFICIENCY BELOW THRESHOLD. ? P0604 - INTERNAL CONTROL MODULE RAM ERROR. This DTC may be caused by enabling the remote throttle feature via the EVIC, and it will be accompanied by a ?service electronic throttle control? message in the EVIC. Other Updates: ? Fuel Filter Minder Calibration Changes ? Cruise control system improvements. ? Improvements in exhaust brake switch operation. ? Charging system improvements for dual alternator applications. ? Various wiTECH data and system test additions and improvements. ? OBD Template changes for P2453. ? Dual Fuel Tank component update. ? Inducement Timer Reset (Feature enable in wiTech). ? PTO Denied Status Message Update. ? PTO Horn Request sen
18-053-142022-08-22. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE; FUEL SYSTEM, DIESEL; EXTERIOR LIGHTING; SERVICE BRAKES, HYDRAULIC. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel. They are as follows: Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For The Following DTCs. These Faults Have Been Changed From One Trip Faults To Two Trip Faults: ? P0201 - P0206 - Fuel Injector X Circuit Open Fault Codes. ? U110E - Lost Ambient Temperature Message. ? P049D - EGR Control Position Exceeding Learning Limit. ? P226C - Turgocharger Boost Control ?A? Slow Response. The Following DTC Has Been Changed From A Two Trip Fault To One Trip Fault: ? U1A24 - Lost Communication With Ammonia Sensor. Improvements To Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For: ? P0087 - Fuel Rail Pressure Too Low. ? P2281 - Air Leak Between MAF And Throttle Body. ? P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. ? P0128 - Thermostat Rationality. In cold ambient temperatures. ? P214D - SCR NOx Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. ? P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. ? P040B - Exhaust Gas Recirculation Temperature Sensor ?A? Circuit Performance. ? U3017 - Control Module Timer/Clock Performance. ? U1421 - Implausible Ignition Key Off Time Received. ? P0420 - Catalyst Efficiency Below Threshold. ? P026B - Injection Timing Performance. ? P04DB - Crankcase Ventilation System Disconnected. ? P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. ? P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. ? P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. ? P2002 - Diesel Particulate Filter Efficiency Below Threshold. ? P0604 - Internal Control Module RAM. ? P1451 - Diesel Particulate Filter System Performance. Other Updates Included: ? Urea system cali
18-002-142022-08-22. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, DIESEL; ELECTRICAL SYSTEM; POWER TRAIN. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM/PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel.Software To Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For The Following Diagnostic Trouble Codes (DTCs). These DTCs Are Currently Tripped As A One Trip Fault And Should Have Been A Two Trip Fault: P0201 - P0206 - Fuel Injector X Circuit/Open Fault Codes. U110E - Lost Ambient Temperature Message. P049D - EGR Control Position Exceeding Learning Limit.Improvements To Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (Mil) Illumination For: P0087 - Fuel Rail Pressure Too Low. P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. P2281 - Air Leak Between MAF And Throttle Body. P0128 - Thermostat Rationality. In low ambient temperatures. U3017 - Control Module Timer/Clock Performance. U1421 - Implausible Ignition Key Off Time Received. P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. P20EE - SCR NOX Catalyst Efficiency Below Threshold - Bank 1. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P0604 - Internal control Module RAM Error. This DTC may be caused by enabling the remote throttle feature via the EVIC, and it will be accompanied by a ?service electronic throttle control? message in the EVIC.Other Updates: Urea system calibration changes. Fuel Filter Minder Calibration Changes. Cruise control system improvements. Improvements in exhaust brake switch operation. Charging system improvements for dual alternator applications. Various wiTECH data and system test additions and improvements. OBD Template changes for P2453. Dual Fuel Tank component update. Inducement Timer Reset (Feature enable in wiTech). PTO Denied Status Message Update. PTO Horn Request sent to Body Control Unit (BCU.)
18-028-162022-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; EQUIPMENT. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. NOTE: There will be a choice between 2 calibrations. One for vehicles that utilize an ammonia sensor and one for vehicles that have had the ammonia sensor removed. Be sure to select the correct software based on vehicle configuration. Prevent or reduce Malfunction Indicator Lamp (MIL) illumination when no defect is present for the following Diagnostic Trouble Codes (DTCs). These faults have been changed from a one trip fault to a two trip fault: · P0201 - P0206 - Fuel Injector X Circuit/Open Fault Codes. · P049D - Exhaust Gas Recirculation (EGR) Control Position Exceeding Learning Limit. Improvements to prevent or reduce Malfunction Indicator Lamp (MIL) illumination when no defect is present for: · **P229E - NOx Sensor Circuit - Bank 1 Sensor 2 (For non-ammonia delete systems only). · P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2 (For non-ammonia delete systems only). · P22A7 - NOx Sensor Heater Circuit Performance - Bank 1 Sensor 2 (For non-ammonia delete systems only). · U059F - Invalid Data Received From NOx Sensor "B" (For non-ammonia delete systems only). · P2459 - Diesel Particulate Filter Regeneration Too Frequent. · P218F - Reductant No Flow Detected. · P242F - Diesel Particulate Filter Restriction - Ash Accumulation.** · P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1 (For ammonia delete systems only). · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). · P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. · U110E - Lost Ambient Temperature Message. · U3017 - Control Module Timer/Clock Performance.
18-079-152022-08-08. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM/PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. WARNING:There will be a choice between 2 calibrations. One for vehicles that utilize an ammonia sensor and one for vehicles that have had the ammonia sensor removed. Be sure to select the correct software based on vehicle configuration. Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From A One Trip Fault To A Two Trip Fault: P0201 - P0206 - Fuel Injector X Circuit/Open Fault Codes. P049D - EGR Control Position Exceeding Learning Limit. Improvements To Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect Is Present For: ? P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). ? P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. ? U110E - Lost Ambient Temperature Message. ? U3017 - Control Module Timer/Clock Performance. ? P0087 - Fuel Rail Pressure Too Low. ? P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. ? P2281 - Air Leak Between MAF And Throttle Body. ? P0128 - Thermostat Rationality. In low ambient temperatures. ? U1421 - Implausible Ignition Key Off Time Received. ? P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. ? P20EE - SCR NOX Catalyst Efficiency Below Threshold - Bank 1. ? P2002 - Diesel Particulate Filter Efficiency Below Threshold. ? P0604 - Internal control Module RAM Error. This DTC may be caused by enabling the remote throttle feature via the EVIC, and it will be accompanied by a ?service electronic throttle control? message in the EVIC. ? SCR Efficiency scan tool test improvement.
18-079-152022-07-25. Service bulletin. EXTERIOR LIGHTING; FUEL SYSTEM, DIESEL; ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM/PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. WARNING:There will be a choice between 2 calibrations. One for vehicles that utilize an ammonia sensor and one for vehicles that have had the ammonia sensor removed. Be sure to select the correct software based on vehicle configuration. Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From A One Trip Fault To A Two Trip Fault: P0201 - P0206 - Fuel Injector X Circuit/Open Fault Codes. P049D - EGR Control Position Exceeding Learning Limit. Improvements To Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect Is Present For: ? P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). ? P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. ? U110E - Lost Ambient Temperature Message. ? U3017 - Control Module Timer/Clock Performance. ? P0087 - Fuel Rail Pressure Too Low. ? P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. ? P2281 - Air Leak Between MAF And Throttle Body. ? P0128 - Thermostat Rationality. In low ambient temperatures. ? U1421 - Implausible Ignition Key Off Time Received. ? P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. ? P20EE - SCR NOX Catalyst Efficiency Below Threshold - Bank 1. ? P2002 - Diesel Particulate Filter Efficiency Below Threshold. ? P0604 - Internal control Module RAM Error. This DTC may be caused by enabling the remote throttle feature via the EVIC, and it will be accompanied by a ?service electronic throttle control? message in the EVIC. Other Updates: ? SCR Efficiency scan tool test improvement.
18-079-152018-12-17. Service bulletin. EXTERIOR LIGHTING; FUEL SYSTEM, DIESEL; ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; BACK OVER PREVENTION; SERVICE BRAKES, HYDRAULIC. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM/PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. WARNING:There will be a choice between 2 calibrations. One for vehicles that utilize an ammonia sensor and one for vehicles that have had the ammonia sensor removed. Be sure to select the correct software based on vehicle configuration. Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From A One Trip Fault To A Two Trip Fault: P0201 - P0206 - Fuel Injector X Circuit/Open Fault Codes. P049D - EGR Control Position Exceeding Learning Limit. Improvements To Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect Is Present For: ? P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). ? P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. ? U110E - Lost Ambient Temperature Message. ? U3017 - Control Module Timer/Clock Performance. ? P0087 - Fuel Rail Pressure Too Low. ? P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. ? P2281 - Air Leak Between MAF And Throttle Body. ? P0128 - Thermostat Rationality. In low ambient temperatures. ? U1421 - Implausible Ignition Key Off Time Received. ? P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. ? P20EE - SCR NOX Catalyst Efficiency Below Threshold - Bank 1. ? P2002 - Diesel Particulate Filter Efficiency Below Threshold. ? P0604 - Internal control Module RAM Error. This DTC may be caused by enabling the remote throttle feature via the EVIC, and it will be accompanied by a ?service electronic throttle control? message in the EVIC. Other Updates: ? SCR Efficiency scan tool test improvement.
18-045-152018-11-26. Service bulletin. ELECTRICAL SYSTEM. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory. ? P2281 - Air Leak Between MAF And Throttle Body. ? P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. ? U3017 - Control Module Timer/Clock Performance. ? U110E - Lost Ambient Temperature Message. ? P0087 - Fuel Rail Pressure Too Low. ? P2281 - Air Leak Between MAF And Throttle Body. ? P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. ? P0128 - Thermostat Rationality. In cold ambient temperatures. ? P214D - SCR NOx Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. ? P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. ? P040B - Exhaust Gas Recirculation Temperature Sensor ?A? Circuit Performance. ? U1421 - Implausible Ignition Key Off Time Received. ? P0420 - Catalyst Efficiency Below Threshold. ? P026B - Injection Timing Performance. ? P04DB - Crankcase Ventilation System Disconnected. ? P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. ? P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. ? P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. ? P2002 - Diesel Particulate Filter Efficiency Below Threshold. ? P0604 - Internal Control Module RAM. ? P1451 - Diesel Particulate Filter System Performance. In addition to the above symptoms, the following software improvements are also included in this update. The Following DTCs Have Been Changed From A One Trip Fault To A Two Trip Fault: ? P0201 - P0206 - Fuel Injector X Circuit Open Fault Codes. ? P049D - EGR Control Position Exceeding Learning Limit. ? P226C - Turbocharger Boost Control
18-053-14 REV. B2018-06-11. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel. They are as follows:Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From A One Trip Fault To A Two Trip Fault: P0201 - P0206 - Fuel Injector X Circuit Open Fault Codes. U110E - Lost Ambient Temperature Message. P049D - EGR Control Position Exceeding Learning Limit. P226C - Turgocharger Boost Control ?A? Slow Response.The Following DTC Has Been Changed From A Two Trip Fault To One Trip Fault: U1A24 - Lost Communication With Ammonia Sensor.Improvements To Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect Is Present For: U3017 - Control Module Timer/Clock Performance P0087 - Fuel Rail Pressure Too Low P2281 - Air Leak Between MAF And Throttle Body P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1 P0128 - Thermostat Rationality. In cold ambient temperatures P214D - SCR NOx Catalyst Outlet Temperature Too High During Particulate Filter Regeneration P24A5 - EGR Cooler Bypass Bank 1 Control Stuck P040B - Exhaust Gas Recirculation Temperature Sensor ?A? Circuit Performance U1421 - Implausible Ignition Key Off Time Received P0420 - Catalyst Efficiency Below Threshold P026B - Injection Timing Performance P04DB - Crankcase Ventilation System Disconnected P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1 P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1 P2002 - Diesel Particulate Filter Efficiency Below Threshold P0604 - Internal Control Module RAM P1451 - Diesel Particulate Filter System Performance.Other Updates Included:
18-002-14 REV. C2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM/PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel.Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From A One Trip Fault To A Two Trip Fault: P0201 - P0206 - Fuel Injector X Circuit/Open Fault Codes. U110E - Lost Ambient Temperature Message. P049D - EGR Control Position Exceeding Learning Limit.Improvements To Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect Is Present For: U3017 - Control Module Timer/Clock Performance. P0087 - Fuel Rail Pressure Too Low. P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. P2281 - Air Leak Between MAF And Throttle Body. P0128 - Thermostat Rationality. In low ambient temperatures. U1421 - Implausible Ignition Key Off Time Received. P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. P20EE - SCR NOX Catalyst Efficiency Below Threshold - Bank 1. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P0604 - Internal control Module RAM Error. This DTC may be caused by enabling the remote throttle feature via the EVIC, and it will be accompanied by a ?service electronic throttle control? message in the EVIC.Other Updates: Urea system calibration changes. Fuel Filter Minder Calibration Changes. Cruise control system improvements. Improvements in exhaust brake switch operation. Charging system improvements for dual alternator applications. Various wiTECH data and system test additions and improvements. OBD Template changes for P2453. Dual Fuel Tank component update. Inducement Timer Reset (Feature enable in wiTech). PTO Denied Status Message Update. PTO Horn Request sent to Body Control Unit (BCU.)
18-053-14 REV. A2018-06-11. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM:SOFTWARE. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel. They are as follows: Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For The Following DTCs. These Faults Have Been Changed From One Trip Faults To Two Trip Faults: * P0201 - P0206 - Fuel Injector X Circuit Open Fault Codes. * U110E - Lost Ambient Temperature Message. * P049D - EGR Control Position Exceeding Learning Limit. * P226C - Turgocharger Boost Control ?A? Slow Response. The Following DTC Has Been Changed From A Two Trip Fault To One Trip Fault: * U1A24 - Lost Communication With Ammonia Sensor. Improvements To Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For: * P0087 - Fuel Rail Pressure Too Low. * P2281 - Air Leak Between MAF And Throttle Body. * P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. * P0128 - Thermostat Rationality. In cold ambient temperatures. * P214D - SCR NOx Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. * P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. * P040B - Exhaust Gas Recirculation Temperature Sensor ?A? Circuit Performance. * U3017 - Control Module Timer/Clock Performance. * U1421 - Implausible Ignition Key Off Time Received. * P0420 - Catalyst Efficiency Below Threshold. * P026B - Injection Timing Performance. * P04DB - Crankcase Ventilation System Disconnected. * P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. * P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. * P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. * P2002 - Diesel Particulate Filter Efficiency Below Threshold. * P0604 - Internal Control Module RAM. * P1451 - Diesel Particulate Filter System Performance. Other Updates Included: * Urea system cali
18-002-14 REV. B2018-06-11. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM/PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel.Software To Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For The Following Diagnostic Trouble Codes (DTCs). These DTCs Are Currently Tripped As A One Trip Fault And Should Have Been A Two Trip Fault: P0201-P0206-Fuel Injector X Circuit/Open Fault Codes. U110E - Lost Ambient Temperature Message. P049D - EGR Control Position Exceeding Learning Limit.Improvements To Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (Mil) Illumination For: P0087 - Fuel Rail Pressure Too Low P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1 P2281 - Air Leak Between MAF And Throttle Body P0128 - Thermostat Rationality. In low ambient temperatures U3017 - Control Module Timer/Clock Performance U1421 - Implausible Ignition Key Off Time Received P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance P20EE - SCR NOX Catalyst Efficiency Below Threshold - Bank 1 P2002 - Diesel Particulate Filter Efficiency Below Threshold P0604 - Internal control Module RAM Error. This DTC may be caused by enabling the remote throttle feature via the EVIC, and it will be accompanied by a service electronic throttle control message in the EVIC.Other Updates: Urea system calibration changes Fuel Filter Minder Calibration Changes Cruise control system improvements Improvements in exhaust brake switch operation Charging system improvements for dual alternator applications Various wiTECH data and system test additions and improvements OBD Template changes for P2453 Dual Fuel Tank component update Inducement Timer Reset (Feature enable in wiTech) PTO Denied Status Message Update PTO Horn Request sent to Body Control Unit (BCU.)
18-053-142018-06-11. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel. They are as follows: Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For The Following DTCs. These Faults Have Been Changed From One Trip Faults To Two Trip Faults: ? P0201 - P0206 - Fuel Injector X Circuit Open Fault Codes. ? U110E - Lost Ambient Temperature Message. ? P049D - EGR Control Position Exceeding Learning Limit. ? P226C - Turgocharger Boost Control ?A? Slow Response. The Following DTC Has Been Changed From A Two Trip Fault To One Trip Fault: ? U1A24 - Lost Communication With Ammonia Sensor. Improvements To Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For: ? P0087 - Fuel Rail Pressure Too Low. ? P2281 - Air Leak Between MAF And Throttle Body. ? P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. ? P0128 - Thermostat Rationality. In cold ambient temperatures. ? P214D - SCR NOx Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. ? P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. ? P040B - Exhaust Gas Recirculation Temperature Sensor ?A? Circuit Performance. ? U3017 - Control Module Timer/Clock Performance. ? U1421 - Implausible Ignition Key Off Time Received. ? P0420 - Catalyst Efficiency Below Threshold. ? P026B - Injection Timing Performance. ? P04DB - Crankcase Ventilation System Disconnected. ? P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. ? P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. ? P2002 - Diesel Particulate Filter Efficiency Below Threshold. ? P0604 - Internal Control Module RAM. ? P1451 - Diesel Particulate Filter System Performance. Other Updates Included: ? Fuel Filter Minder Calibration Changes ? Cruise control
18-002-14 REV. A2018-06-11. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE. Flash: Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM/PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. Software To Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For The Following Diagnostic Trouble Codes (DTCs). These DTCs Are Currently Tripped As A One Trip Fault And Should Have Been A Two Trip Fault: ? P0201 - P0206 - FUEL INJECTOR X CIRCUIT/OPEN Fault Codes. ? U110E - LOST AMBIENT TEMPERATURE MESSAGE. ? P049D - EGR CONTROL POSITION EXCEEDED LEARNING LIMIT. Improvements To Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (Mil) Illumination For: ? P0087 - FUEL RAIL PRESSURE TOO LOW. ? P0544 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT - SENSOR 1/1. ? P2281 - AIR LEAK BETWEEN MAF AND THROTTLE BODY. ? P0128 - THERMOSTAT RATIONALITY. In low ambient temperatures. ? U3017 - CONTROL MODULE TIMER/CLOCK PERFORMANCE. ? U1421 - IMPLAUSIBLE IGNITION KEY OFF TIME RECEIVED. ? P202E - (DIESEL EXHAUST FLUID) REDUCTANT INJECTOR PERFORMANCE. ? P20EE - SCR NOx CATALYST EFFICIENCY BELOW THRESHOLD - BANK 1. ? P2002 - DIESEL PARTICULATE FILTER EFFICIENCY BELOW THRESHOLD. ? P0604 - INTERNAL CONTROL MODULE RAM ERROR. This DTC may be caused by enabling the remote throttle feature via the EVIC, and it will be accompanied by a ?service electronic throttle control? message in the EVIC. Other Updates: ? Fuel Filter Minder Calibration Changes ? Cruise control system improvements. ? Improvements in exhaust brake switch operation. ? Charging system improvements for dual alternator applications. ? Various wiTECH data and system test additions and improvements. ? OBD Template changes for P2453. ? Dual Fuel Tank component update. ? Inducement Timer Reset (Feature enable in wiTech). ? PTO Denied Status Message Update. ? PTO Horn Request sen
18-002-142018-05-21. Service bulletin. FUEL SYSTEM, DIESEL; ELECTRICAL SYSTEM. Flash: Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM/PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For The Following Diagnostic Trouble Codes (DTC?s). These DTC?s Are Currently Tripped As A One Trip Fault And Should Have Been A Two Trip Fault: ? P049D - EGR CONTROL POSITION EXCEEDED LEARNING LIMIT Improvements To Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (Mil) Illumination For: ? P202E - (DIESEL EXHAUST FLUID) REDUCTANT INJECTOR PERFORMANCE ? P20EE - SCR NOx CATALYST EFFICIENCY BELOW THRESHOLD - BANK 1 ? P2002 - DIESEL PARTICULATE FILTER EFFICIENCY BELOW THRESHOLD ? P0604 - INTERNAL CONTROL MODULE RAM ERROR. This DTC may be caused by enabling the remote throttle feature via the EVIC, and it will be accompanied by a ?service electronic throttle control? message in the EVIC. Other Updates: ? OBD Template changes for P2453 ? Fuel Filter Minder Calibration Changes ? Dual Fuel Tank component update ? Inducement Timer Reset (Feature enable in wiTech) ? PTO Denied Status Message Update ? PTO Horn Request sent to Body Control Unit (BCU) ? Wait To Start (WTS) bulb check timing improvements (1 second) ? Frozen CAC Diagnostic Improvement
18-028-16 REV. A2018-05-07. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. NOTE: There will be a choice between 2 calibrations. One for vehicles that utilize an ammonia sensor and one for vehicles that have had the ammonia sensor removed. Be sure to select the correct software based on vehicle configuration. Prevent or reduce Malfunction Indicator Lamp (MIL) illumination when no defect is present for the following Diagnostic Trouble Codes (DTCs). These faults have been changed from a one trip fault to a two trip fault: · P0201 - P0206 - Fuel Injector X Circuit/Open Fault Codes. · P049D - Exhaust Gas Recirculation (EGR) Control Position Exceeding Learning Limit. Improvements to prevent or reduce Malfunction Indicator Lamp (MIL) illumination when no defect is present for: · **P229E - NOx Sensor Circuit - Bank 1 Sensor 2 (For non-ammonia delete systems only). · P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2 (For non-ammonia delete systems only). · P22A7 - NOx Sensor Heater Circuit Performance - Bank 1 Sensor 2 (For non-ammonia delete systems only). · U059F - Invalid Data Received From NOx Sensor "B" (For non-ammonia delete systems only). · P2459 - Diesel Particulate Filter Regeneration Too Frequent. · P218F - Reductant No Flow Detected. · P242F - Diesel Particulate Filter Restriction - Ash Accumulation.** · P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1 (For ammonia delete systems only). · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). · P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. · U110E - Lost Ambient Temperature Message. · U3017 - Control Module Timer/Clock Performance.
18-028-16 REV. A2018-02-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. NOTE: There will be a choice between 2 calibrations. One for vehicles that utilize an ammonia sensor and one for vehicles that have had the ammonia sensor removed. Be sure to select the correct software based on vehicle configuration. Prevent or reduce Malfunction Indicator Lamp (MIL) illumination when no defect is present for the following Diagnostic Trouble Codes (DTCs). These faults have been changed from a one trip fault to a two trip fault: · P0201 - P0206 - Fuel Injector X Circuit/Open Fault Codes. · P049D - Exhaust Gas Recirculation (EGR) Control Position Exceeding Learning Limit. Improvements to prevent or reduce Malfunction Indicator Lamp (MIL) illumination when no defect is present for: · **P229E - NOx Sensor Circuit - Bank 1 Sensor 2 (For non-ammonia delete systems only). · P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2 (For non-ammonia delete systems only). · P22A7 - NOx Sensor Heater Circuit Performance - Bank 1 Sensor 2 (For non-ammonia delete systems only). · U059F - Invalid Data Received From NOx Sensor "B" (For non-ammonia delete systems only). · P2459 - Diesel Particulate Filter Regeneration Too Frequent. · P218F - Reductant No Flow Detected. · P242F - Diesel Particulate Filter Restriction - Ash Accumulation.** · P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1 (For ammonia delete systems only). · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). · P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. · U110E - Lost Ambient Temperature Message. · U3017 - Control Module Timer/Clock Performance.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.