WenmarOpen by Wenmar Pro

Service bulletins for the 2024 Ram 2500

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

304 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
S25080000142025-02-11. Service bulletin. ELECTRICAL SYSTEM. Security Gateway (SGW) Module is Setting Diagnostic Trouble Code (DTC) U3033-00 Control Module Security Certificate Missing or Invalid
91004932025-02-06. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE:BODY. SWITCH AND BEZEL Front Door Before replacing the Window Switch/Mirror Switch, please follow these steps: 1.- Check for what DTC are detected and take proper steps acceding to the DTC's. 2.- Make sure all the switches are properly connected to their harness, disconnect the switch and reconnect it. 3.- Review the window Switch for any physical issue (Button stuck, broken) If after performing these steps the switch remains faulty. Follow suggested repairs per diagnostics performed.
S258A0000052025-02-06. Service bulletin. ELECTRICAL SYSTEM. Trailer Tow App Gauges Not Showing Data in Widget Screen
90039802025-01-29. Service bulletin. ELECTRICAL SYSTEM. SWITCH Headlamp Before replacing the Headlamp Switch for faulty dimmer operation. Please follow the next steps to corroborate if the Headlamp Switch is malfunctioning: 1.- Please disconnect and reconnect the headlamp Switch. And verify if the issue is corrected. 2.- Review the internal resistance of the switch: a.- For the Right Dimmer (IP) between Pins 6 & 3. The value should be around 5.74 KOhms, when in the lowest position to 311 ohms in the top position (Parade Detent). b.- For the left Dimmer (Ambient Light) between pins 8 & 3. The value should be around 14.52 KOhms, when in the lowest position to 182 ohms in the top position. If a problem is found in the resistor values. Please replace the Switch.
S1408000384 REV.H2025-01-28. Service bulletin. ELECTRICAL SYSTEM. Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
91004902025-01-23. Service bulletin. ELECTRICAL SYSTEM. SWITCH Instrument Panel Before replacing the driver window switch, please follow these steps: 1.- Review the Trailer brake Switch for any physical issue (Button stuck, broke). If no physical issue identified, move to next steps. 2.- Make sure the switch harness is properly connected, disconnect the switch and reconnect it, and reverify the issue. 3.- Check for what DTC are detected and take proper steps. 4.- Review the internal resistance of the switch to corroborate if it is shorted: a) Between Pins 10&2 it should be around 13ohms +/- 4ohms b) Between Pins 3 & 4 and 4 & 6, 160 ohms +/-10 Ohms If a problem is found in the resistor values. Please replace the Switch.
S25230000022025-01-10. Service bulletin. STRUCTURE:BODY; ELECTRICAL SYSTEM. Outside Exterior Mirror Power Extend And/Or Retract Is Not Fully Functional.
S1408000384 REV.G2025-01-09. Service bulletin. ELECTRICAL SYSTEM. Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S24080001232024-12-20. Service bulletin. ELECTRICAL SYSTEM. Push to Start Button Has a Delay Switching Ignition Positions, DTCs (Diagnostic Trouble Codes), B1A7D-2A Start Button - Stuck, U103C-00 KIN/IGNM Communication
91004622024-12-19. Service bulletin. ELECTRICAL SYSTEM. SWITCH Mirror Before replacing the driver window switch, please follow these steps: 1.- Review the telescopic mirror Switch for any physical issue (Button stuck, broke). If no physical issue identified, move to next steps. 2.- Make sure the switch harness is properly connected, disconnect the switch and reconnect it, and reverify the issue. 3.- Check for what DTC are detected and take proper steps. If there are no DTC's nor physical defectives, then the telescopic mirror switches can't be replaced.
91004592024-12-19. Service bulletin. ELECTRICAL SYSTEM. switch Electronic range select Before replacing the switch electronic gear selector 68379834AB due to P0826-29, P0826- 11 active codes, please follow these steps: 1.- Refer to service library procedure and follow diagnosis steps at BCM. 2.- If failure still present, make sure the switch is properly connected and there is no corrosion or pinching, disconnect the switch & reconnect it, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between gear selector switch and BCM. For example, try switching between driving modes. 4.- Read at the BCM diagnosis session if BCM is receiving information from gear selector. 5.- Do a hard reset to BCM and evaluate if any DTC or failure code is set. Retest if failure still present. If there are no DTC's, physical defects, gear selector inop, then the Electronic Gear Selector Switch does not need to be replaced.
S248A0000182024-12-10. Service bulletin. ELECTRICAL SYSTEM. Trailer Tow Pages App Gauges Not Showing Data After Radio Update
S2422000001 REV.C2024-11-13. Service bulletin. WHEELS; ELECTRICAL SYSTEM. Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
1007742024-11-01. Service bulletin. ELECTRICAL SYSTEM. SWITCH - HEADLAMP
978022024-10-08. Service bulletin. ELECTRICAL SYSTEM. SWITCH - HEADLAMP
S24230000432024-10-04. Service bulletin. ELECTRICAL SYSTEM. Dome Lamp LED And Incandescent Bulb Servicing.
S2208000153 REV.B2024-09-27. Service bulletin. ELECTRICAL SYSTEM; WHEELS. Tire Pressure Lamp Flashing, No Tire Pressures Displayed, “Tire Pressure Module (TPM) System Unavailable” Message Displayed on Cluster
S228A000017 REV.A2024-09-23. Service bulletin. ELECTRICAL SYSTEM. Battery Drain Suspected or "Identified" From USB or Media Hub
S2423000027 REV.A2024-09-06. Service bulletin. ELECTRICAL SYSTEM. Horn Sound Is Weak, Off Tone, Or Inoperative.
S24230000392024-08-19. Service bulletin. ELECTRICAL SYSTEM. Wiper Motor Inoperative. Wiper Doesn’t Work or Stops Randomly On Glass
S248A0000112024-07-25. Service bulletin. ELECTRICAL SYSTEM. Driver Hears Noise, Static or Can Not Hear Phone Caller on Other End
91003892024-07-24. Service bulletin. ELECTRICAL SYSTEM. CAN Star Block Connector Customer finds MIL light on and technician finds DTC for loss of communication on one or more modules. In repair procedure the dealerships are replacing the CAN star block connector during their root cause process with returned parts showing no trouble found. Here is a list of steps the dealers can follow to determine if they have a defective CAN star block connector using a multimeter: Step 1: Visually review CAN star block for damage and ensure back cover has all locking tabs engaged. If a bent pin, cracked or damaged housing or locking tab is not engaged is observed then replacement is required. Step 2: Identify Connector #1 as the 3 Pin Connector cavity Step 3: Measure resistance between Pin#1 and Pin#2 in Connector #1. Acceptable values are 120.4 Ohms to 139.8 Ohms. If resistance is outside of this range then replacement is required. Step 4: Measure the continuity between Pin#1 in Connector #1 to Pin#1 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required. Step 5: Measure the continuity between Pin#2 in Connector #1 to Pin#2 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required.
S248A0000102024-07-22. Service bulletin. ELECTRICAL SYSTEM. Satellite Radio Displays “Satellite Hardware Error” Message
S2408000015 REV.C2024-07-10. Service bulletin. ELECTRICAL SYSTEM. Remote Keyless Entry (RKE) Functions Do Not Work, Intermittent Vehicle Response When Using the RKE, Key Not Programmed, Adding Remote Start
91003622024-07-08. Service bulletin. ELECTRICAL SYSTEM; STEERING. MODULE Steering Control Before replacing the steering column control module (SCCM), please follow these steps: 1.- Make sure all the switches' and airbag's harness are properly connected, disconnect the switches and reconnect them, and reverify the issue. 2.- Pull the SCCM fuse for 60 sec and then reinstall it. 3.- Reverify if Steering wheel switches are inoperative. If there are no DTC's, physical defects, nor switches inop, then SCCM does not need to be replaced.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.