Service bulletins for the 2014 Ram 2500
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
516 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Transmission and driveline are shown. Show all
| 9001762 | 2022-08-22. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Part Description: Thermostat, Engine Issue Description: Important! There has been an application change to the Cummins turbo diesel thermostat. When replacing a thermostat confirm the correct replacement is choosen.~ 2010, 2011, and 2012 RAM Trucks 2500/3500/4500/5500 engine coolant operating temperature has been increased to 200 degrees requiring thermostat 68067109AA.~ 2009, 2013, and 2014 RAM Trucks 2500/3500/4500/5500 engine coolant operating temperature is 190 degrees requiring thermostat 68005464AA.~ These thermostats are not interchangeable and doing so will result in reduced engine performance. |
|---|---|
| 1804215 | 2022-08-22. Service bulletin. POWER TRAIN. Diagnostic And System Improvements. |
| 18-004-14 REV. A | 2022-08-22. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Flash: Malfunction Indicator Lamp (MIL) Illumination. Includes Various Driveability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes (DTC?s) have been set: (Further improvements over what was released in SB 18-004-14) (applies only to DD/DP vehicles) (applies only to DD/DP vehicles) P2066 - Fuel Level Sensor 2 Performance (applies only to DJ/D2 vehicles) P0441 - Evap Purge System Performance P2504 - Charging System Output High P04D0 - Cooled EGR Temperature Sensor Circuit Low P04D1 - Cooled EGR Temperature Sensor Circuit High |
| 18-025-14 | 2022-08-22. Service bulletin. POWER TRAIN. Flash: Powertrain System Improvements/Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The following powertrain system improvements/enhancements are included in this software release: ? Enhanced Automatic Oil Change Indicator(EAOCI) system enhancements that force the use of the severe duty cycle algorithm anytime the PCM is replaced. The vehicle duty cycle information used in the EAOCI calculation is stored in the PCM and cannot be recovered/transferred when the controller is replaced. As a result, the severe duty cycle is used in these scenarios to ensure the customer receives a timely oil change required message. ? Corrected a generic scan tool display issue regarding Mode 6 data accuracy. ? Improved transmission Quick Learn routine performance (Applies only to DJ vehicles) |
| 18-096-16 | 2022-08-15. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT. Flash: 6.4L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. NOTE: **This bulletin contains optional software update that should only be used in situations where the customer is specifically complaining of a Drone Noise, Shudder, Pulsation, or Vibration under light throttle applications while vehicle is operating in MDS/ECO mode. There will be two separate software options displayed on the wiTECH flash tab. The software file released for this condition contains the verbiage ?OPTIONAL?. The other file is the standard software that does not contain improvements for the Drone/Shudder concern. If for some reason the customer finds this shudder improvement objectionable, the PCM software may be returned/reflashed to the standard version. Both software versions will address the remaining conditions noted in the bulletin. A small number of customers may experience a surge, shudder or pulsation type sensation when driving on smooth road surfaces at highway speeds of 64-129 km/h (40-80 mph).** During normal diagnostics a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) present: · **P0335 - Crankshaft Position Sensor Circuit.** · P0300 - Multiple Cylinder Misfire, cold Idle misfire (DJ,D2 or DD vehicles only). · P030X - Cylinder Misfire (any cylinder). · P04D1 - Cooled EGR Temperature Sensor Circuit High. · P04D0 - Cooled EGR Temperature Sensor Circuit Low. · P2504 - Charging System Output High. · P0441 - Evap Purge System Performance. · P2066 - Fuel Level Sensor 2 Performance. · P0401 - EGR System Performance (DJ/D2 vehicles only). · P2096 - Downstream Fuel Trim System 1 Lean (DD/DP vehicles only). · P2098 - Downstream Fuel Trim System 2 Lean (DD/DP vehicles only). · |
| S2008000113 Rev. | 2021-05-24. Service bulletin. POWER TRAIN. No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message |
| V51 | 2020-01-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Customer Satisfaction Notification V51 Reprogram Powertrain Control Module |
| 55309 | 2019-07-15. Service bulletin. EQUIPMENT; POWER TRAIN. Power Transfer Unit |
| 54583 | 2019-07-15. Service bulletin. POWER TRAIN. Transmission ? With Torque Converter |
| 9003988 | 2019-07-15. Service bulletin. POWER TRAIN. Brake Transmission Shift Interlock (BTSI) Please contact Stacey Davis at (248) 260-6078 or stacey.davis@fcagroup.com if the following scenario occurs; The T79 or U11 recall was completed where the shifter inspection was acceptable and the software flash was performed but then the customer comes back needing the BTSI bracket replaced for coming out of park without the brake or key. |
| 18-112-15 | 2019-05-20. Service bulletin. POWER TRAIN. Flash: Powertrain System Improvements/Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application. DS vehicles equipped with a 3.6L engine (sales code ERB). * Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. * Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DS vehicles equipped with a 5.7L engine (sales code EZH). * System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -20°F (-29°C). * Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. * Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DJ, DD, and D2 vehicles equipped with a 5.7L engine (sales code EZC or EZF). * U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful). * Transmission torque management enhancement when shifting from drive to reverse. * Software to correct Malfunction Indicator Lamp (MIL) illumination with Diagnostic Trouble Code (DTC) P0481 - Cooling Fan 2 Control Circuit/Open setting in the PCM memory. * Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. * Corrected a generic scan tool display issue regarding Mode 6 data accuracy. * Improved tran |
| 03-004-15 | 2019-05-20. Service bulletin. POWER TRAIN. Vibration During Quick Launch While Towing This bulletin involves replacing the rear prop shaft, if required. The customer may describe a vibration feeling during a fast launch from 0 mph (0 kph) to 11 mph (18 kph) and the vehicle hauling a heavy load. This vibration is most noticeable at a launch from a stop, at Wide Open Throttle (WOT) while towing a heavy trailer. |
| 18-045-15 REV A | 2019-05-20. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: ? P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). ? U110E - Lost Ambient Temperature Message. ? P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. ? P2281 - Air Leak Between MAF And Throttle Body. ? P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. ? U3017 - Control Module Timer/Clock Performance. ? P0087 - Fuel Rail Pressure Too Low. ? P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. ? P0128 - Thermostat Rationality. In cold ambient temperatures. ? P214D - SCR NOx Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. ? P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. ? P040B - Exhaust Gas Recirculation Temperature Sensor ?A? Circuit Performance. ? U1421 - Implausible Ignition Key Off Time Received. ? P0420 - Catalyst Efficiency Below Threshold. ? P026B - Injection Timing Performance. ? P04DB - Crankcase Ventilation System Disconnected. ? P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. ? P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. ? P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. ? P2002 - Diesel Particulate Filter Efficiency Below Threshold. ? P0604 - Internal Control Module RAM. ? P1451 - Diesel Particulate Filter System Performance. In addition to the above symptoms, the following software improvements are also included in this update: The Following DTCs Have Been Changed From A One Trip Fault To A Two Trip Fault: ? P0201 - P0206 - Fuel injector |
| 18-042-15 | 2019-05-20. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; EQUIPMENT; ENGINE. Flash: 6.4L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0300 - Multiple Cylinder Misfire, cold Idle misfire (DJ,D2 or DD vehicles only). ? P030X - Cylinder Misfire (any cylinder) (Additional improvements over the last software update). ? P04D1 - Cooled EGR Temperature Sensor Circuit High. ? P04D0 - Cooled EGR Temperature Sensor Circuit Low. ? P2504 - Charging System Output High. ? P0441 - Evap Purge System Performance. ? P2066 - Fuel Level Sensor 2 Performance. ? P0401 - EGR System Performance (DJ/D2 vehicles only). ? P2096 - Downstream Fuel Trim System 1 Lean (DD/DP vehicles only). ? P2098 - Downstream Fuel Trim System 2 Lean (DD/DP vehicles only). ? P0740 - TCC Out of Range (DD vehicles equipped with a DFP automatic transmission). Customers may also experience any of the following conditions: ? Slightly elevated idle speed noticed during engine warm-up when in Reverse or Drive and when operating in cold ambient temperatures. ? PTO mobile mode cancels or deactivates when vehicle comes to a stop (DD/DP vehicles only). ? Engine cycles in and out of MDS mode too often when operating in PTO stationary mode (DD/DP vehicles only). ? PTO stationary mode cancels or deactivates when PTO up-fit equipment loads fluctuate (DD/DP vehicles only) The following powertrain system improvements/enhancements are also included in this software release: ? Improve Idle at high altitudes (DJ,D2 or DD vehicles only). ? Spark knock on vehicle with low octane fuel (DJ,D2 or DD vehicles only). ? Operator idle speed control enhancements. ? Raise 4x4 low range minimum engine speed from 725 to 800 RPM. ? Raise minimum engine speed to allow MDS activa |
| 68317270A | 2018-11-26. Service bulletin. POWER TRAIN. 2014 KL 9-Speed service transaxle with 2015 common hardware This 9-speed transaxle must be ordered thru Mopar?s Powertrain Service Center (PSC) for a specific VIN and must be installed in that vehicle or the correct calibration will not load to the Engine Control Module (ECM) and Transmission Control Module (TCM).~ This 9-speed transaxle assembly requires an update to the Engine Control Module AND the Transmission Control Module using WiTech. Failure to complete both updates will result in possible damage and/or incorrect operation of this unit. |
| 68211004A | 2018-11-26. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. Shifter - Automatic Trans Before this part is replaced for any issue please call John Grzecki on cell (248) 379- 0969. If you do not receive a return call within 15 minutes, proceed with the repair. Please be sure to accurately record any DTCs identified with the scan tool and document them on the repair order. |
| 68090604A | 2018-11-26. Service bulletin. POWER TRAIN; POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE). Power Transfer Unit Prior to replacing the PTU, please review the following .~ Check if the service 4WD light is intermittent by driving under heavy throttle will produce a C1494-92 DTC, if yes, please call FCA axle engineering and do not replace the PTU. Bruce Michel at cell (248) 260-8641, or Jian Zhu at cell (248) 379- 1132. If neither answers with 15 minutes then proceed with the repair. ~ If the service 4WD light lamp is on steady then replace the Power Transfer Unit. |
| 68206041A$ | 2018-06-11. Service bulletin. POWER TRAIN. Fan Support Assembly, Fan Support Bearing, Fan Pulley If you are replacing this part due to fan hub bearing failure, please also replace the fan clutch assembly using current Mopar stock (part number 52014729A$).~ Once installed, contact Christine Donegan at (866) 799-1692 ext 1257 to initiate a fast track request for the return of the parts for analysis. |
| 18-072-16 | 2018-06-11. Service bulletin. EXTERIOR LIGHTING; POWER TRAIN; STRUCTURE; ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE. Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application. DS vehicles equipped with a 3.6L engine (Sales Code ERB). U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful). ASD Relay Enhancements To Improve Fuel Pump Relay Initialization At Key On - (Auto Shutdown). Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DS vehicles equipped with a 5.7L engine (Sales Code EZH). U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful. ASD Relay Enhancements To Improve Fuel Pump Relay Initialization At Key On - (Auto Shutdown). System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -29°C (-20°F). Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DJ, DD, and D2 vehicles equipped with a 5.7L engine (Sales Codes EZC or EZF). U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful). Transmission torque management enhancement when shifting from drive to reverse. Software to correct Malfunction Indicator Lamp (MIL) illumination wi |
| 18-053-14 REV. B | 2018-06-11. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel. They are as follows:Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From A One Trip Fault To A Two Trip Fault: P0201 - P0206 - Fuel Injector X Circuit Open Fault Codes. U110E - Lost Ambient Temperature Message. P049D - EGR Control Position Exceeding Learning Limit. P226C - Turgocharger Boost Control ?A? Slow Response.The Following DTC Has Been Changed From A Two Trip Fault To One Trip Fault: U1A24 - Lost Communication With Ammonia Sensor.Improvements To Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect Is Present For: U3017 - Control Module Timer/Clock Performance P0087 - Fuel Rail Pressure Too Low P2281 - Air Leak Between MAF And Throttle Body P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1 P0128 - Thermostat Rationality. In cold ambient temperatures P214D - SCR NOx Catalyst Outlet Temperature Too High During Particulate Filter Regeneration P24A5 - EGR Cooler Bypass Bank 1 Control Stuck P040B - Exhaust Gas Recirculation Temperature Sensor ?A? Circuit Performance U1421 - Implausible Ignition Key Off Time Received P0420 - Catalyst Efficiency Below Threshold P026B - Injection Timing Performance P04DB - Crankcase Ventilation System Disconnected P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1 P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1 P2002 - Diesel Particulate Filter Efficiency Below Threshold P0604 - Internal Control Module RAM P1451 - Diesel Particulate Filter System Performance.Other Updates Included: |
| 18-072-14 | 2018-06-11. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM:SOFTWARE. Flash: Compressed Natural Gas (CNG) Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. Software to prevent Malfunction Indicator Lamp (MIL) illumination with no defect found for Diagnostic Trouble Code (DTC) P0481 - Cooling Fan 2 Control Circuit/Open setting in the PCM. Harsh shift improvement when shifting from drive to reverse. |
| 18-025-14 REV. A | 2018-06-11. Service bulletin. POWER TRAIN. Flash: Powertrain System Improvements/Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application.DS vehicles equipped with a 3.6L engine (sales code ERB). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DS vehicles equipped with a 5.7L engine (sales code EZH). Charging system voltage regulator control improvements. System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -20°F (-29°C). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DJ, DD, and D2 vehicles equipped with a 5.7L engine (sales code EZC) Transmission torque management enhancement when shifting from drive to reverse. Software to correct Malfunction Indicator Lamp (MIL) illumination with Diagnostic Trouble Code (DTC) P0481 - Cooling Fan 2 Control Circuit/Open setting in the PCM memory. Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy. Improved transmission Quick Learn routine performance |
| 18-053-14 REV. A | 2018-06-11. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM:SOFTWARE. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel. They are as follows: Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For The Following DTCs. These Faults Have Been Changed From One Trip Faults To Two Trip Faults: * P0201 - P0206 - Fuel Injector X Circuit Open Fault Codes. * U110E - Lost Ambient Temperature Message. * P049D - EGR Control Position Exceeding Learning Limit. * P226C - Turgocharger Boost Control ?A? Slow Response. The Following DTC Has Been Changed From A Two Trip Fault To One Trip Fault: * U1A24 - Lost Communication With Ammonia Sensor. Improvements To Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For: * P0087 - Fuel Rail Pressure Too Low. * P2281 - Air Leak Between MAF And Throttle Body. * P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. * P0128 - Thermostat Rationality. In cold ambient temperatures. * P214D - SCR NOx Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. * P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. * P040B - Exhaust Gas Recirculation Temperature Sensor ?A? Circuit Performance. * U3017 - Control Module Timer/Clock Performance. * U1421 - Implausible Ignition Key Off Time Received. * P0420 - Catalyst Efficiency Below Threshold. * P026B - Injection Timing Performance. * P04DB - Crankcase Ventilation System Disconnected. * P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. * P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. * P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. * P2002 - Diesel Particulate Filter Efficiency Below Threshold. * P0604 - Internal Control Module RAM. * P1451 - Diesel Particulate Filter System Performance. Other Updates Included: * Urea system cali |
| 18-004-14 REV. B | 2018-06-11. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ELECTRICAL SYSTEM. Flash: Malfunction Indicator Lamp (MIL) Illumination. Includes Various Driveability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes (DTCs) have been set: (Further improvements over what was released in SB 18-004-14) (applies only to DD/DP vehicles) (applies only to DD/DP vehicles) P2066 - Fuel Level Sensor 2 Performance (applies only to DJ/D2 vehicles) P0441 - Evap Purge System Performance P2504 - Charging System Output High P04D0 - Cooled EGR Temperature Sensor Circuit Low P04D1 - Cooled EGR Temperature Sensor Circuit High (applies only to DD vehicles equipped with a DFP automatic transmission) |
| 18-004-14 REV. A | 2018-06-11. Service bulletin. POWER TRAIN. Flash: Malfunction Indicator Lamp (MIL) Illumination. Includes Various Driveability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes (DTC?s) have been set: (Further improvements over what was released in SB 18-004-14) (applies only to DD/DP vehicles) (applies only to DD/DP vehicles) P2066 - Fuel Level Sensor 2 Performance (applies only to DJ/D2 vehicles) P0441 - Evap Purge System Performance P2504 - Charging System Output High P04D0 - Cooled EGR Temperature Sensor Circuit Low P04D1 - Cooled EGR Temperature Sensor Circuit High |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.