WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Ram 2500

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

516 on file from NHTSA, as of 2026-10-19.

About P0300 on the 2014 Ram 2500: what the code means, and the bulletins and recalls about the same components.

By type

By component

By trouble code

Only bulletins with trouble code: P0300 are shown. Show all

Bulletins, newest first
18025142023-01-17. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Powertrain System Improvements/Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application.DS vehicles equipped with a 3.6L engine (sales code ERB). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DS vehicles equipped with a 5.7L engine (sales code EZH). Charging system voltage regulator control improvements. System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -20°F (-29°C). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DJ, DD, and D2 vehicles equipped with a 5.7L engine (sales code EZC) Transmission torque management enhancement when shifting from drive to reverse.
1802514REVA2022-09-26. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Flash: Powertrain System Improvements/Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application.DS vehicles equipped with a 3.6L engine (sales code ERB). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DS vehicles equipped with a 5.7L engine (sales code EZH). Charging system voltage regulator control improvements. System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -20°F (-29°C). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DJ, DD, and D2 vehicles equipped with a 5.7L engine (sales code EZC) Transmission torque management enhancement when shifting from drive to reverse. Software to correct Malfunction Indicator Lamp (MIL) illumination with Diagnostic Trouble Code (DTC) P0481 - Cooling Fan 2 Control Circuit/Open setting in the PCM memory. Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy. Improved transmission Quick Learn routine performance
18-072-162022-08-22. Service bulletin. EXTERIOR LIGHTING; STRUCTURE; POWER TRAIN; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application. DS vehicles equipped with a 3.6L engine (Sales Code ERB). · **U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful). · ASD Relay Enhancements To Improve Fuel Pump Relay Initialization At Key On - (Auto Shutdown).** · Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. · Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DS vehicles equipped with a 5.7L engine (Sales Code EZH). · **U0140 - Lost Communication With Body Control Module (attempting to clear this · ASD Relay Enhancements To Improve Fuel Pump Relay Initialization At Key On - (Auto Shutdown).** · System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -29°C (-20°F). · Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. · Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DJ, DD, and D2 vehicles equipped with a 5.7L engine (Sales Codes EZC or EZF). · U0140 - Lost Communication With Body Control Module (attempting to clear this · Transmission torque management enhancement when shifting from drive to reverse. · Software to correct Malfunction Indicator Lamp (MIL) illumination wi
18-096-162022-08-15. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT. Flash: 6.4L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. NOTE: **This bulletin contains optional software update that should only be used in situations where the customer is specifically complaining of a Drone Noise, Shudder, Pulsation, or Vibration under light throttle applications while vehicle is operating in MDS/ECO mode. There will be two separate software options displayed on the wiTECH flash tab. The software file released for this condition contains the verbiage ?OPTIONAL?. The other file is the standard software that does not contain improvements for the Drone/Shudder concern. If for some reason the customer finds this shudder improvement objectionable, the PCM software may be returned/reflashed to the standard version. Both software versions will address the remaining conditions noted in the bulletin. A small number of customers may experience a surge, shudder or pulsation type sensation when driving on smooth road surfaces at highway speeds of 64-129 km/h (40-80 mph).** During normal diagnostics a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) present: · **P0335 - Crankshaft Position Sensor Circuit.** · P0300 - Multiple Cylinder Misfire, cold Idle misfire (DJ,D2 or DD vehicles only). · P030X - Cylinder Misfire (any cylinder). · P04D1 - Cooled EGR Temperature Sensor Circuit High. · P04D0 - Cooled EGR Temperature Sensor Circuit Low. · P2504 - Charging System Output High. · P0441 - Evap Purge System Performance. · P2066 - Fuel Level Sensor 2 Performance. · P0401 - EGR System Performance (DJ/D2 vehicles only). · P2096 - Downstream Fuel Trim System 1 Lean (DD/DP vehicles only). · P2098 - Downstream Fuel Trim System 2 Lean (DD/DP vehicles only). ·
18-112-152019-05-20. Service bulletin. POWER TRAIN. Flash: Powertrain System Improvements/Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application. DS vehicles equipped with a 3.6L engine (sales code ERB). * Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. * Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DS vehicles equipped with a 5.7L engine (sales code EZH). * System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -20°F (-29°C). * Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. * Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DJ, DD, and D2 vehicles equipped with a 5.7L engine (sales code EZC or EZF). * U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful). * Transmission torque management enhancement when shifting from drive to reverse. * Software to correct Malfunction Indicator Lamp (MIL) illumination with Diagnostic Trouble Code (DTC) P0481 - Cooling Fan 2 Control Circuit/Open setting in the PCM memory. * Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. * Corrected a generic scan tool display issue regarding Mode 6 data accuracy. * Improved tran
18-042-152019-05-20. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; EQUIPMENT; ENGINE. Flash: 6.4L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0300 - Multiple Cylinder Misfire, cold Idle misfire (DJ,D2 or DD vehicles only). ? P030X - Cylinder Misfire (any cylinder) (Additional improvements over the last software update). ? P04D1 - Cooled EGR Temperature Sensor Circuit High. ? P04D0 - Cooled EGR Temperature Sensor Circuit Low. ? P2504 - Charging System Output High. ? P0441 - Evap Purge System Performance. ? P2066 - Fuel Level Sensor 2 Performance. ? P0401 - EGR System Performance (DJ/D2 vehicles only). ? P2096 - Downstream Fuel Trim System 1 Lean (DD/DP vehicles only). ? P2098 - Downstream Fuel Trim System 2 Lean (DD/DP vehicles only). ? P0740 - TCC Out of Range (DD vehicles equipped with a DFP automatic transmission). Customers may also experience any of the following conditions: ? Slightly elevated idle speed noticed during engine warm-up when in Reverse or Drive and when operating in cold ambient temperatures. ? PTO mobile mode cancels or deactivates when vehicle comes to a stop (DD/DP vehicles only). ? Engine cycles in and out of MDS mode too often when operating in PTO stationary mode (DD/DP vehicles only). ? PTO stationary mode cancels or deactivates when PTO up-fit equipment loads fluctuate (DD/DP vehicles only) The following powertrain system improvements/enhancements are also included in this software release: ? Improve Idle at high altitudes (DJ,D2 or DD vehicles only). ? Spark knock on vehicle with low octane fuel (DJ,D2 or DD vehicles only). ? Operator idle speed control enhancements. ? Raise 4x4 low range minimum engine speed from 725 to 800 RPM. ? Raise minimum engine speed to allow MDS activa
18-072-162018-06-11. Service bulletin. EXTERIOR LIGHTING; POWER TRAIN; STRUCTURE; ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE. Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application. DS vehicles equipped with a 3.6L engine (Sales Code ERB). U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful). ASD Relay Enhancements To Improve Fuel Pump Relay Initialization At Key On - (Auto Shutdown). Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DS vehicles equipped with a 5.7L engine (Sales Code EZH). U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful. ASD Relay Enhancements To Improve Fuel Pump Relay Initialization At Key On - (Auto Shutdown). System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -29°C (-20°F). Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DJ, DD, and D2 vehicles equipped with a 5.7L engine (Sales Codes EZC or EZF). U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful). Transmission torque management enhancement when shifting from drive to reverse. Software to correct Malfunction Indicator Lamp (MIL) illumination wi
18-025-14 REV. A2018-06-11. Service bulletin. POWER TRAIN. Flash: Powertrain System Improvements/Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application.DS vehicles equipped with a 3.6L engine (sales code ERB). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DS vehicles equipped with a 5.7L engine (sales code EZH). Charging system voltage regulator control improvements. System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -20°F (-29°C). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DJ, DD, and D2 vehicles equipped with a 5.7L engine (sales code EZC) Transmission torque management enhancement when shifting from drive to reverse. Software to correct Malfunction Indicator Lamp (MIL) illumination with Diagnostic Trouble Code (DTC) P0481 - Cooling Fan 2 Control Circuit/Open setting in the PCM memory. Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy. Improved transmission Quick Learn routine performance
18-096-162018-05-07. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Flash: 6.4L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. NOTE: **This bulletin contains optional software update that should only be used in situations where the customer is specifically complaining of a Drone Noise, Shudder, Pulsation, or Vibration under light throttle applications while vehicle is operating in MDS/ECO mode. There will be two separate software options displayed on the wiTECH flash tab. The software file released for this condition contains the verbiage ?OPTIONAL?. The other file is the standard software that does not contain improvements for the Drone/Shudder concern. If for some reason the customer finds this shudder improvement objectionable, the PCM software may be returned/reflashed to the standard version. Both software versions will address the remaining conditions noted in the bulletin. A small number of customers may experience a surge, shudder or pulsation type sensation when driving on smooth road surfaces at highway speeds of 64-129 km/h (40-80 mph).** During normal diagnostics a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) present: · **P0335 - Crankshaft Position Sensor Circuit.** · P0300 - Multiple Cylinder Misfire, cold Idle misfire (DJ,D2 or DD vehicles only). · P030X - Cylinder Misfire (any cylinder). · P04D1 - Cooled EGR Temperature Sensor Circuit High. · P04D0 - Cooled EGR Temperature Sensor Circuit Low. · P2504 - Charging System Output High. · P0441 - Evap Purge System Performance. · P2066 - Fuel Level Sensor 2 Performance. · P0401 - EGR System Performance (DJ/D2 vehicles only). · P2096 - Downstream Fuel Trim System 1 Lean (DD/DP vehicles only). · P2098 - Downstream Fuel Trim System 2 Lean (DD/DP vehicles only). ·
18-096-162018-02-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Flash: 6.4L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. NOTE: **This bulletin contains optional software update that should only be used in situations where the customer is specifically complaining of a Drone Noise, Shudder, Pulsation, or Vibration under light throttle applications while vehicle is operating in MDS/ECO mode. There will be two separate software options displayed on the wiTECH flash tab. The software file released for this condition contains the verbiage ?OPTIONAL?. The other file is the standard software that does not contain improvements for the Drone/Shudder concern. If for some reason the customer finds this shudder improvement objectionable, the PCM software may be returned/reflashed to the standard version. Both software versions will address the remaining conditions noted in the bulletin. A small number of customers may experience a surge, shudder or pulsation type sensation when driving on smooth road surfaces at highway speeds of 64-129 km/h (40-80 mph).** During normal diagnostics a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) present: · **P0335 - Crankshaft Position Sensor Circuit.** · P0300 - Multiple Cylinder Misfire, cold Idle misfire (DJ,D2 or DD vehicles only). · P030X - Cylinder Misfire (any cylinder). · P04D1 - Cooled EGR Temperature Sensor Circuit High. · P04D0 - Cooled EGR Temperature Sensor Circuit Low. · P2504 - Charging System Output High. · P0441 - Evap Purge System Performance. · P2066 - Fuel Level Sensor 2 Performance. · P0401 - EGR System Performance (DJ/D2 vehicles only). · P2096 - Downstream Fuel Trim System 1 Lean (DD/DP vehicles only). · P2098 - Downstream Fuel Trim System 2 Lean (DD/DP vehicles only). ·
18-072-162016-09-16. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:SOFTWARE. "FLASH: POWERTRAIN DIAGNOSTIC AND SYSTEM ENHANCEMENTS THIS BULLETIN INVOLVES REPROGRAMMING THE POWERTRAIN CONTROL MODULE (PCM) WITH THE LATEST AVAILABLE SOFTWARE. THE FOLLOWING POWERTRAIN SYSTEM IMPROVEMENTS/ENHANCEMENTS ARE INCLUDED IN THIS SOFTWARE RELEASE. THESE ENHANCEMENTS ARE LISTED BY VEHICLE APPLICATION. DS VEHICLES EQUIPPED WITH A 3.6L ENGINE (SALES CODE ERB). · **U0140 - LOST COMMUNICATION WITH BODY CONTROL MODULE (ATTEMPTING TO CLEAR THIS DTC WILL BE UNSUCCESSFUL). · ASD RELAY ENHANCEMENTS TO IMPROVE FUEL PUMP RELAY INITIALIZATION AT KEY ON - (AUTO SHUTDOWN).** · ENHANCED AUTOMATIC OIL CHANGE INDICATOR (EAOCI) SYSTEM IMPROVEMENTS TO SWITCH TO A SEVERE DUTY CYCLE ALGORITHM ANYTIME THE PCM IS REPLACED TO ENSURE THE CUSTOMER RECEIVES A TIMELY OIL CHANGE REQUIRED MESSAGE. · CORRECTED A GENERIC SCAN TOOL DISPLAY ISSUE REGARDING MODE 6 DATA ACCURACY. DS VEHICLES EQUIPPED WITH A 5.7L ENGINE (SALES CODE EZH). · **U0140 - LOST COMMUNICATION WITH BODY CONTROL MODULE (ATTEMPTING TO CLEAR THIS DTC WILL BE UNSUCCESSFUL). · ASD RELAY ENHANCEMENTS TO IMPROVE FUEL PUMP RELAY INITIALIZATION AT KEY ON - (AUTO SHUTDOWN).** · SYSTEM IMPROVEMENTS TO PREVENT MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION WITH A DIAGNOSTIC TROUBLE CODE (DTC) P0300 - MULTIPLE CYLINDER MISFIRE WHEN USING A BLOCK HEATER IN AMBIENT TEMPERATURES GREATER THAN -29°C (-20°F). · ENHANCED AUTOMATIC OIL CHANGE INDICATOR (EAOCI) SYSTEM IMPROVEMENTS TO SWITCH TO A SEVERE DUTY CYCLE ALGORITHM ANYTIME THE PCM IS REPLACED TO ENSURE THE CUSTOMER RECEIVES A TIMELY OIL CHANGE REQUIRED MESSAGE. · CORRECTED A GENERIC SCAN TOOL DISPLAY ISSUE REGARDING MODE 6 DATA ACCURACY. DJ, DD, AND D2 VEHICLES EQUIPPED WITH A 5.7L ENGINE (SALES CODES EZC OR EZF). · U0140 - LOST COMMUNICATION WITH BODY CONTROL MODULE (ATTEMPTING TO CLEAR THIS DTC WILL BE UNSUCCESSFUL). · TRANSMISSION TORQUE MANAGEMENT ENHANCEMENT WHEN SHIFTING FROM DRIVE TO REVERSE.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.