P0300 on the 2014 Ram 2500
The bulletins listed name this code in NHTSA's summary, or are about the same components. A bulletin or a recall listed here may apply to the model year. None of it is a diagnosis.
Nobody has written a description of this code yet.
| 1802514 | 2023-01-17. Service bulletin. Flash: Powertrain System Improvements/Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application.DS vehicles equipped with a 3.6L engine (sales code ERB). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DS vehicles equipped with a 5.7L engine (sales code EZH). Charging system voltage regulator control improvements. System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -20°F (-29°C). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DJ, DD, and D2 vehicles equipped with a 5.7L engine (sales code EZC) Transmission torque management enhancement when shifting from drive to reverse. |
|---|---|
| 1802514REVA | 2022-09-26. Service bulletin. Flash: Powertrain System Improvements/Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application.DS vehicles equipped with a 3.6L engine (sales code ERB). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DS vehicles equipped with a 5.7L engine (sales code EZH). Charging system voltage regulator control improvements. System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -20°F (-29°C). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DJ, DD, and D2 vehicles equipped with a 5.7L engine (sales code EZC) Transmission torque management enhancement when shifting from drive to reverse. Software to correct Malfunction Indicator Lamp (MIL) illumination with Diagnostic Trouble Code (DTC) P0481 - Cooling Fan 2 Control Circuit/Open setting in the PCM memory. Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy. Improved transmission Quick Learn routine performance |
| 18-072-16 | 2022-08-22. Service bulletin. Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application. DS vehicles equipped with a 3.6L engine (Sales Code ERB). · **U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful). · ASD Relay Enhancements To Improve Fuel Pump Relay Initialization At Key On - (Auto Shutdown).** · Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. · Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DS vehicles equipped with a 5.7L engine (Sales Code EZH). · **U0140 - Lost Communication With Body Control Module (attempting to clear this · ASD Relay Enhancements To Improve Fuel Pump Relay Initialization At Key On - (Auto Shutdown).** · System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -29°C (-20°F). · Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. · Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DJ, DD, and D2 vehicles equipped with a 5.7L engine (Sales Codes EZC or EZF). · U0140 - Lost Communication With Body Control Module (attempting to clear this · Transmission torque management enhancement when shifting from drive to reverse. · Software to correct Malfunction Indicator Lamp (MIL) illumination wi |
| 18-096-16 | 2022-08-15. Service bulletin. Flash: 6.4L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. NOTE: **This bulletin contains optional software update that should only be used in situations where the customer is specifically complaining of a Drone Noise, Shudder, Pulsation, or Vibration under light throttle applications while vehicle is operating in MDS/ECO mode. There will be two separate software options displayed on the wiTECH flash tab. The software file released for this condition contains the verbiage ?OPTIONAL?. The other file is the standard software that does not contain improvements for the Drone/Shudder concern. If for some reason the customer finds this shudder improvement objectionable, the PCM software may be returned/reflashed to the standard version. Both software versions will address the remaining conditions noted in the bulletin. A small number of customers may experience a surge, shudder or pulsation type sensation when driving on smooth road surfaces at highway speeds of 64-129 km/h (40-80 mph).** During normal diagnostics a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) present: · **P0335 - Crankshaft Position Sensor Circuit.** · P0300 - Multiple Cylinder Misfire, cold Idle misfire (DJ,D2 or DD vehicles only). · P030X - Cylinder Misfire (any cylinder). · P04D1 - Cooled EGR Temperature Sensor Circuit High. · P04D0 - Cooled EGR Temperature Sensor Circuit Low. · P2504 - Charging System Output High. · P0441 - Evap Purge System Performance. · P2066 - Fuel Level Sensor 2 Performance. · P0401 - EGR System Performance (DJ/D2 vehicles only). · P2096 - Downstream Fuel Trim System 1 Lean (DD/DP vehicles only). · P2098 - Downstream Fuel Trim System 2 Lean (DD/DP vehicles only). · |
| 18-112-15 | 2019-05-20. Service bulletin. Flash: Powertrain System Improvements/Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application. DS vehicles equipped with a 3.6L engine (sales code ERB). * Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. * Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DS vehicles equipped with a 5.7L engine (sales code EZH). * System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -20°F (-29°C). * Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. * Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DJ, DD, and D2 vehicles equipped with a 5.7L engine (sales code EZC or EZF). * U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful). * Transmission torque management enhancement when shifting from drive to reverse. * Software to correct Malfunction Indicator Lamp (MIL) illumination with Diagnostic Trouble Code (DTC) P0481 - Cooling Fan 2 Control Circuit/Open setting in the PCM memory. * Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. * Corrected a generic scan tool display issue regarding Mode 6 data accuracy. * Improved tran |
| 18-042-15 | 2019-05-20. Service bulletin. Flash: 6.4L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0300 - Multiple Cylinder Misfire, cold Idle misfire (DJ,D2 or DD vehicles only). ? P030X - Cylinder Misfire (any cylinder) (Additional improvements over the last software update). ? P04D1 - Cooled EGR Temperature Sensor Circuit High. ? P04D0 - Cooled EGR Temperature Sensor Circuit Low. ? P2504 - Charging System Output High. ? P0441 - Evap Purge System Performance. ? P2066 - Fuel Level Sensor 2 Performance. ? P0401 - EGR System Performance (DJ/D2 vehicles only). ? P2096 - Downstream Fuel Trim System 1 Lean (DD/DP vehicles only). ? P2098 - Downstream Fuel Trim System 2 Lean (DD/DP vehicles only). ? P0740 - TCC Out of Range (DD vehicles equipped with a DFP automatic transmission). Customers may also experience any of the following conditions: ? Slightly elevated idle speed noticed during engine warm-up when in Reverse or Drive and when operating in cold ambient temperatures. ? PTO mobile mode cancels or deactivates when vehicle comes to a stop (DD/DP vehicles only). ? Engine cycles in and out of MDS mode too often when operating in PTO stationary mode (DD/DP vehicles only). ? PTO stationary mode cancels or deactivates when PTO up-fit equipment loads fluctuate (DD/DP vehicles only) The following powertrain system improvements/enhancements are also included in this software release: ? Improve Idle at high altitudes (DJ,D2 or DD vehicles only). ? Spark knock on vehicle with low octane fuel (DJ,D2 or DD vehicles only). ? Operator idle speed control enhancements. ? Raise 4x4 low range minimum engine speed from 725 to 800 RPM. ? Raise minimum engine speed to allow MDS activa |
| 18-072-16 | 2018-06-11. Service bulletin. Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application. DS vehicles equipped with a 3.6L engine (Sales Code ERB). U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful). ASD Relay Enhancements To Improve Fuel Pump Relay Initialization At Key On - (Auto Shutdown). Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DS vehicles equipped with a 5.7L engine (Sales Code EZH). U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful. ASD Relay Enhancements To Improve Fuel Pump Relay Initialization At Key On - (Auto Shutdown). System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -29°C (-20°F). Enhanced Automatic Oil Change Indicator (EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy. DJ, DD, and D2 vehicles equipped with a 5.7L engine (Sales Codes EZC or EZF). U0140 - Lost Communication With Body Control Module (attempting to clear this DTC will be unsuccessful). Transmission torque management enhancement when shifting from drive to reverse. Software to correct Malfunction Indicator Lamp (MIL) illumination wi |
| 18-025-14 REV. A | 2018-06-11. Service bulletin. Flash: Powertrain System Improvements/Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application.DS vehicles equipped with a 3.6L engine (sales code ERB). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DS vehicles equipped with a 5.7L engine (sales code EZH). Charging system voltage regulator control improvements. System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -20°F (-29°C). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DJ, DD, and D2 vehicles equipped with a 5.7L engine (sales code EZC) Transmission torque management enhancement when shifting from drive to reverse. Software to correct Malfunction Indicator Lamp (MIL) illumination with Diagnostic Trouble Code (DTC) P0481 - Cooling Fan 2 Control Circuit/Open setting in the PCM memory. Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy. Improved transmission Quick Learn routine performance |
| 18-096-16 | 2018-05-07. Service bulletin. Flash: 6.4L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. NOTE: **This bulletin contains optional software update that should only be used in situations where the customer is specifically complaining of a Drone Noise, Shudder, Pulsation, or Vibration under light throttle applications while vehicle is operating in MDS/ECO mode. There will be two separate software options displayed on the wiTECH flash tab. The software file released for this condition contains the verbiage ?OPTIONAL?. The other file is the standard software that does not contain improvements for the Drone/Shudder concern. If for some reason the customer finds this shudder improvement objectionable, the PCM software may be returned/reflashed to the standard version. Both software versions will address the remaining conditions noted in the bulletin. A small number of customers may experience a surge, shudder or pulsation type sensation when driving on smooth road surfaces at highway speeds of 64-129 km/h (40-80 mph).** During normal diagnostics a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) present: · **P0335 - Crankshaft Position Sensor Circuit.** · P0300 - Multiple Cylinder Misfire, cold Idle misfire (DJ,D2 or DD vehicles only). · P030X - Cylinder Misfire (any cylinder). · P04D1 - Cooled EGR Temperature Sensor Circuit High. · P04D0 - Cooled EGR Temperature Sensor Circuit Low. · P2504 - Charging System Output High. · P0441 - Evap Purge System Performance. · P2066 - Fuel Level Sensor 2 Performance. · P0401 - EGR System Performance (DJ/D2 vehicles only). · P2096 - Downstream Fuel Trim System 1 Lean (DD/DP vehicles only). · P2098 - Downstream Fuel Trim System 2 Lean (DD/DP vehicles only). · |
| 18-096-16 | 2018-02-21. Service bulletin. Flash: 6.4L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. NOTE: **This bulletin contains optional software update that should only be used in situations where the customer is specifically complaining of a Drone Noise, Shudder, Pulsation, or Vibration under light throttle applications while vehicle is operating in MDS/ECO mode. There will be two separate software options displayed on the wiTECH flash tab. The software file released for this condition contains the verbiage ?OPTIONAL?. The other file is the standard software that does not contain improvements for the Drone/Shudder concern. If for some reason the customer finds this shudder improvement objectionable, the PCM software may be returned/reflashed to the standard version. Both software versions will address the remaining conditions noted in the bulletin. A small number of customers may experience a surge, shudder or pulsation type sensation when driving on smooth road surfaces at highway speeds of 64-129 km/h (40-80 mph).** During normal diagnostics a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) present: · **P0335 - Crankshaft Position Sensor Circuit.** · P0300 - Multiple Cylinder Misfire, cold Idle misfire (DJ,D2 or DD vehicles only). · P030X - Cylinder Misfire (any cylinder). · P04D1 - Cooled EGR Temperature Sensor Circuit High. · P04D0 - Cooled EGR Temperature Sensor Circuit Low. · P2504 - Charging System Output High. · P0441 - Evap Purge System Performance. · P2066 - Fuel Level Sensor 2 Performance. · P0401 - EGR System Performance (DJ/D2 vehicles only). · P2096 - Downstream Fuel Trim System 1 Lean (DD/DP vehicles only). · P2098 - Downstream Fuel Trim System 2 Lean (DD/DP vehicles only). · |
11 on file from NHTSA, as of 2026-10-19. See them in the bulletin list. A bulletin lists model years: read the document for which vehicles it concerns.