Service bulletins for the 2014 Ram 2500
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
516 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Engine are shown. Show all
| 55096 | 2019-07-15. Service bulletin. ENGINE. Engine Oil- OW20 |
|---|---|
| 54931 | 2019-07-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. TAILPIPE - EXHAUST |
| 9003357 | 2019-07-15. Service bulletin. ENGINE; EQUIPMENT. ADAPTER, Engine Oil Filter (Pentastar V6) Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison (248-292-9510) ron.dallison@fcagroup.com Joe Lovell (734) 309-6467 - joe.lovell@fcagroup.com If no response in 15 minutes, proceed with repair. All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. |
| 18-088-15 | 2019-05-20. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT. P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 This bulletin involves verifying the proper operation of the Diesel Exhaust Fluid (DEF) system and, if necessary, replacing the Selective Catalyst Reduction (SCR) Catalyst assembly. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find Diagnostic Trouble Code (DTC) P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 set in the Powertrain Control Module (PCM) memory. |
| 18-045-15 REV A | 2019-05-20. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: ? P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). ? U110E - Lost Ambient Temperature Message. ? P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. ? P2281 - Air Leak Between MAF And Throttle Body. ? P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. ? U3017 - Control Module Timer/Clock Performance. ? P0087 - Fuel Rail Pressure Too Low. ? P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. ? P0128 - Thermostat Rationality. In cold ambient temperatures. ? P214D - SCR NOx Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. ? P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. ? P040B - Exhaust Gas Recirculation Temperature Sensor ?A? Circuit Performance. ? U1421 - Implausible Ignition Key Off Time Received. ? P0420 - Catalyst Efficiency Below Threshold. ? P026B - Injection Timing Performance. ? P04DB - Crankcase Ventilation System Disconnected. ? P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. ? P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. ? P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. ? P2002 - Diesel Particulate Filter Efficiency Below Threshold. ? P0604 - Internal Control Module RAM. ? P1451 - Diesel Particulate Filter System Performance. In addition to the above symptoms, the following software improvements are also included in this update: The Following DTCs Have Been Changed From A One Trip Fault To A Two Trip Fault: ? P0201 - P0206 - Fuel injector |
| 18-042-15 | 2019-05-20. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; EQUIPMENT; ENGINE. Flash: 6.4L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0300 - Multiple Cylinder Misfire, cold Idle misfire (DJ,D2 or DD vehicles only). ? P030X - Cylinder Misfire (any cylinder) (Additional improvements over the last software update). ? P04D1 - Cooled EGR Temperature Sensor Circuit High. ? P04D0 - Cooled EGR Temperature Sensor Circuit Low. ? P2504 - Charging System Output High. ? P0441 - Evap Purge System Performance. ? P2066 - Fuel Level Sensor 2 Performance. ? P0401 - EGR System Performance (DJ/D2 vehicles only). ? P2096 - Downstream Fuel Trim System 1 Lean (DD/DP vehicles only). ? P2098 - Downstream Fuel Trim System 2 Lean (DD/DP vehicles only). ? P0740 - TCC Out of Range (DD vehicles equipped with a DFP automatic transmission). Customers may also experience any of the following conditions: ? Slightly elevated idle speed noticed during engine warm-up when in Reverse or Drive and when operating in cold ambient temperatures. ? PTO mobile mode cancels or deactivates when vehicle comes to a stop (DD/DP vehicles only). ? Engine cycles in and out of MDS mode too often when operating in PTO stationary mode (DD/DP vehicles only). ? PTO stationary mode cancels or deactivates when PTO up-fit equipment loads fluctuate (DD/DP vehicles only) The following powertrain system improvements/enhancements are also included in this software release: ? Improve Idle at high altitudes (DJ,D2 or DD vehicles only). ? Spark knock on vehicle with low octane fuel (DJ,D2 or DD vehicles only). ? Operator idle speed control enhancements. ? Raise 4x4 low range minimum engine speed from 725 to 800 RPM. ? Raise minimum engine speed to allow MDS activa |
| 68085740A | 2018-12-17. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Part Description: Engine Out NOx Sensor 1/1, System Out NOx Sensor 1/2 Issue Description: If you receive a DJ/D2 with a MIL illumination and DTC P229F, please do not replace any parts at this time. Cummins Engineering is currently investigating the root cause of the concern and is requesting to visit a dealership with this DTC to gather valuable information. Please contact Christine Donegan at (866) 799-1692 ext 1257~ If causal part replacement is the System Out NOx sensor (Bank 1, Sensor 2) PNs 68085740AA, or 68197109AA, please file claim under LOP 250810. If for the Engine Out NOx Sensor (Bank 1, Sensor 1) use LOP 250809. |
| 13284 | 2018-12-17. Service bulletin. ENGINE. Title Filter - Engine Oil Start Date: 10/23/2015 7:00 AM End Date Message You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part number: 68109834AA. Replacement part number is: 68229402AA. 68229402AA is designed to work on both DS and W K with 3.0L Ecodiesel(EXF)in NAFTA. Please return suspect parts back to your facing depot using Return Code 02, before 13 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com. |
| 09-002-15 | 2018-12-10. Service bulletin. ENGINE AND ENGINE COOLING. Knocking Noise From Engine After Sitting Overnight This bulletin involves evaluating the engine for cold start knocking noise typically after an overnight cold soak. Some engines during this build period may have been built with incorrect piston wrist pins. The wrist pins will cause an audible knocking noise upon start up. The knocking noise will typically reduce after approximately 30 minutes of idle time. Engine replacement will be required. Some customers may comment they hear an audible knocking noise coming form the engine after start up for approximately 30 minutes. This only occurs after cold start when the vehicle has been sitting over night. |
| 68080819A | 2018-11-26. Service bulletin. ENGINE. Camshaft Position Sensor If replacing a camshaft position sensor for P0340 and/or P0344 fault codes, please review information below and contact Andrew Action on his cell phone: (248) 421- 4130. If no response is received within 15 minutes, please continue with repair.~ Before clearing any codes please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Andrew Acton by email: andrew.acton@fcagroup.com~ Instructions to access CamCrank Sync Event Monitor:~ - From wiTECH main screen~ - Monitors tab~ - OBDII Monitors~ - Select Cam Crank Synchronization Event Monitor from the list~ - Should bring up 3 or 4 pages of data~ - Click on create PDF icon in lower right corner~ - email PDF to andrew.acton@fcagroup.com |
| 68079375A | 2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV). Crankshaft Position Sensor Before replacing this part due to a P0335 fault code, please contact Andrew Acton at cell (248) 421-4130. Engineering is interested in the condition(s) present when the fault occurs.~ If no response is received within 15 minutes, then continue with repair.~ If possible, please send Freeze Frame data and Mark Sync Event data to andrew.acton@fcagroup.com~ To Retrieve Marks Data on WiTech:~ 1) Choose ?Monitors? and select ?OBDII Monitors? from the drop down box.~ 2) At the next Screen, choose ?Cam Crank Synchronization Monitor?.~ 3) Once you select the Cam Crank Synchronization event Monitor, you will get to the three pages of Marks Event Data. |
| 05191925A | 2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY. Radiator If vehicle comes in for transmission fluid leaking from trans-oil cooler fittings on the radiator, please check the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Loosen the hex nut on the top flared fitting on the radiator tank.~ 3. Torque the top flared fitting to 235 +/- 15 Lb-In.~ 4. Torque hex nut to 100 +/- 10 Lb-In.~ 5. Repeat for bottom flared fitting.~ 6. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~ ~ If vehicle is in need of a new radiator for another reason, check the new radiator for correct torque on the trans-oil cooler fitting per steps 2-5 above.~ ~ If radiator has a yellow mark by the trans-oil cooler fittings the torque does not have to be checked. |
| 05149141A | 2018-11-26. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV). Camshaft Position Sensor If replacing a camshaft position sensor for P0340, P0344, P0345, P0349, P0365, P0369, P0390 or P0394 fault codes, please review information below and contact Tom Nies on his cell phone: (248) 494-0187. If no response is received within 15 minutes, please continue with repair. Before clearing any codes, please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Tom Nies by email: tom.nies@fcagroup.com~ Instructions to access Cam/Crank Sync Event Monitor: - From wiTECH main screen - Monitors tab - OBDII Monitors - Select Cam Crank Synchronization Event Monitor from the list - Should bring up 3 or 4 pages of data - Click on create PDF icon in lower right corner - email PDF to tom.nies@fcagroup.com |
| 04861963A | 2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT. Evaporative System Integrity Monitor switch (ESIM) Prior to replacing this component on a 2015 Dodge Journey (JC), please call Bob Bruni at cell (248) 736-8958. If a response is not received within 15 minutes, then continue with the necessary repair. |
| 25-001-15 REV-A | 2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL. Diesel Exhaust Fluid (DEF) Level Sensor Manufacturing Defect This bulletin involves replacing the DEF pump module. A manufacturing defect in the level sensor may have occurred, if the level sensor was built within the time frame listed above. There may be a Malfunction Indicator Lamp (MIL) illuminated. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs). ? P203B - Reductant Level Sensor Circuit Performance. ? P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. ? P203D - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit High. |
| 25-001-15 | 2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Diesel Exhaust Fluid (DEF) Level Gauge Inaccurate Or Stuck This bulletin involves verifying the correct DEF level in the tank and if necessary, replacing the DEF pump module. A small number of customers may comment that their DEF level gauge is stuck for long periods of time or is erratic. The customer may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs). ? P203B - Reductant Level Sensor Circuit Performance ? P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. ? P203D - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit High. |
| 09-004-16 | 2018-06-18. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Cummins Service Engine Replacement This bulletin involves replacing the engine assembly. Remanufactured long block or short block was installed during a prior repair. A new replacement engine will be installed. |
| 18-034-14 REV. A | 2018-06-18. Service bulletin. ENGINE. P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit |
| 22842 | 2018-06-11. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. 05187880AC - Inspect and Return: Relay Assy - Heater Intake Air You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 05187880AC. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 31st August, 2016. |
| 20610 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. P/N 04573460 - Inspect &Return: Rocker Assy - Intake Valve RT You have been identified as either having stock, or have stock in transit to your dealership. Please return part number 04573460 which have a packaging date of 2016-06-13. Reference attached picture for reference. Please return suspect parts back to your facing depot using Return Code 02, before 29 August, 2016. |
| 17006 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. 68085119AE,Inspect and Return: Exhaust Pipe Assy - Frt W/Catalytic Converter You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 68085119AE. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 30 June, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com. |
| 16887 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE. Return: ALTERNATOR - ENGINE You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part numbers: R4801313AC replacement part number are 04801313AD respectively which are in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 8 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com |
| 25-001-17 | 2018-06-11. Service bulletin. FUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING:ENGINE:DIESEL. Diesel Exhaust Fluid This bulletin provides information regarding the Diesel Exhaust Fluid (DEF) vehicle delivery fill guidelines. |
| 30731 | 2018-06-11. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING. 04627694AA Purge Control - Valve You have been identified as either having stock, or have stock in transit to your dealership. Suspect stock of part number: 04627694AA must be returned. See attached for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 17 April, 2017. |
| 9003694 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.