WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Ram 1500

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

472 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
1097272026-01-28. Service bulletin. ENGINE. Water Pump & Chain Case Cover
1097242026-01-28. Service bulletin. ENGINE. Water Pump & Chain Case Cover
91006392025-08-13. Service bulletin. ENGINE. Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
S25050000012025-03-05. Service bulletin. ENGINE. CEL (Check Engine Lamp) C006A-49 Multi-Axis Acceleration Sensor Internal Electronic Failure And C10CC-00 ESC Sensors.
983542024-05-31. Other. ENGINE. Valve - EGR
09023232024-01-16. Service bulletin. ENGINE AND ENGINE COOLING. Throttle Blade Icing Service Fix Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P2072 - Electronic Throttle Control System - Ice Blockage. ? P2110 - Electronic Throttle Control - Forced Limited RPM. ? P2118 - Electronic Throttle Control Motor Current Performance - Bank 1. The customer may also comment on the following: ? The vehicle may not start (below freezing conditions - typically -7 °C (-20 °F)) This bulletin involves removing the PCV valve and hose to dry out, drying out the throttle body and installing an updated make-up air hose, air cleaner lid and changing the oil.
91002792024-01-16. Service bulletin. ENGINE AND ENGINE COOLING. COOLER Engine Oil Please be aware that the oil cooler seal is serviceable as a standalone part and should be considered for replacement as a remedy for fluid leak.
9003357A2024-01-02. Service bulletin. ENGINE AND ENGINE COOLING. ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
S23070000022023-10-02. Service bulletin. ENGINE AND ENGINE COOLING. Suspected engine coolant leak.
07007232023-07-31. Service bulletin. ENGINE AND ENGINE COOLING. Water Quality When Mixed With Engine Coolant
18048232023-05-30. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
9003357a2023-04-17. Service bulletin. ENGINE AND ENGINE COOLING. ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
90033572023-04-17. Service bulletin. ENGINE AND ENGINE COOLING. ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
S21090000042023-01-17. Service bulletin. ENGINE AND ENGINE COOLING. Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
S18090000072023-01-17. Service bulletin. ENGINE. Customer Complaint May Include Engine Oil Leak Or Consumption
850492023-01-09. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:SEALS/GASKETS; UNKNOWN OR OTHER. COOLER - EGR
90037042023-01-09. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. Transmission Oil Pan, Heater (TMU), Tube or O-ring Applies to vehicles equipped with 8 speed transmissions only; if you have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
S22090000032023-01-09. Service bulletin. ENGINE; ELECTRICAL SYSTEM:SEAT HEATER:WIRING HARNESS; ELECTRICAL SYSTEM:HAND HEATER:WIRING HARNESS. Complete Engine Assembly Replacements Arriving Without Engine Wiring Harness.
S22090000042022-12-19. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
90037042022-10-31. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Trans Oil Pan, Heater Tube or O-ring, Heater Applies to vehicles equipped with 8 speed transmissions only; If you have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. If you have a leak concern please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. See your parts specialist for the proper gasket for the repair.
90037712022-10-24. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY; ELECTRICAL SYSTEM. Radiator Before replacing the radiator call Matt Mihm at FCA Auburn Hills cell: (248) 736- 6542 to answer a few questions. If no response in 15 minutes, please proceed with repair. When replacing Radiator for damage on engine side of radiator, also replace fan module and ship the old fan using the same ticket number.
08094202022-10-17. Service bulletin. EXTERIOR LIGHTING; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Flash: Drivetrain Control Module (DTCM) Update This bulletin involves reprogramming the DTCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set::If the customer has any concerns with the transfer case or if the tech performs any repairs on the transfer case, the software must be updated.C140E - Transfer Case Motor Blocked. If DTC C140E is present, follow normal diagnostic procedures before updating the DTCM.In addition the customer may describe the following:The ?Service 4WD? message/fault is displayed in the Instrument Panel Cluster (IPC). Transfer case shift fork tabs broken during range shift. Noisy (clunking/ratcheting) transfer case range shifts. Failure to complete transfer case range shifts. The following software enhancement is available:This update will help reduce premature transfer case failure.
682340412022-10-17. Service bulletin. ENGINE AND ENGINE COOLING; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM. Thermal Expansion Valve (TXV), H-valve For D trucks only; When diagnosing an A/C system leak at the TXV (Thermal Expansion Valve, H-valve), do not replace the TXV unless it has been proven to be defective for function or for a leak. Instead replace just the O-ring(s) part number 05161806AA, 68046015AA, 68100682AA, 68100676AA. For any questions call Matt Mihm cell (248) 736-6542. If no response in 15 minutes, please continue with repair.~ ~___________________________________________________________________~ Contact us at CAGRIS@Chrysler.com for feedback related ONLY to this GPOP Tech Tip. Please include the Part Number(s) and Tech Tip Part Description of the Tech Tip you are referencing for our tracking system.
683328102022-10-17. Service bulletin. ENGINE AND ENGINE COOLING. Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar® Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 N·m [21 ft. lbs.].
S18090000072022-10-17. Service bulletin. ENGINE AND ENGINE COOLING. Customer Complaint May Include Engine Oil Leak Or Consumption

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.