Service bulletins for the 2014 Ram 1500
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
615 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Engine are shown. Show all
| 18-034-14 REV. A | 2018-06-18. Service bulletin. ENGINE. P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit |
|---|---|
| 68225378A$ | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL. 3.0L V6 Turbo Diesel - Sales Code EXF A crankshaft locking tool marked 630 is installed on all 3.0L EXG long blocks (Lower rear left side of block under starter location). This tool locks the crankshaft at 30? ATDC. Refer to: Valve Timing ? Standard Procedure ? LOCKING ENGINE 30 DEGREE AFTER TDC IN TechCONNECT for further details. This tool must be removed after the the injection pump has been installed on the engine. The tool will be replaced with the engine block plug from the engine being removed. The engine will not turn over with this tool installed.~ |
| 22842 | 2018-06-11. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. 05187880AC - Inspect and Return: Relay Assy - Heater Intake Air You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 05187880AC. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 31st August, 2016. |
| 20610 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. P/N 04573460 - Inspect &Return: Rocker Assy - Intake Valve RT You have been identified as either having stock, or have stock in transit to your dealership. Please return part number 04573460 which have a packaging date of 2016-06-13. Reference attached picture for reference. Please return suspect parts back to your facing depot using Return Code 02, before 29 August, 2016. |
| 17006 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. 68085119AE,Inspect and Return: Exhaust Pipe Assy - Frt W/Catalytic Converter You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 68085119AE. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 30 June, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com. |
| 16887 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE. Return: ALTERNATOR - ENGINE You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part numbers: R4801313AC replacement part number are 04801313AD respectively which are in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 8 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com |
| 30731 | 2018-06-11. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING. 04627694AA Purge Control - Valve You have been identified as either having stock, or have stock in transit to your dealership. Suspect stock of part number: 04627694AA must be returned. See attached for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 17 April, 2017. |
| 9003694 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system |
| 68105583A | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~ |
| 18-028-14 REV. D | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on Diagnostic Trouble Codes (DTC) that may have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel Ratio Control. P2459-00 - Diesel Particulate Filter Regeneration Frequency P0133-00 - O2 Sensor 1/1 Slow Response P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2) P0171-00 - Fuel System 1/1 Lean P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1) P0045-00 - Turbocharger Boost Control Circuit/Open P0087-00 - Fuel Rail Pressure Too Low P009A-00 - Intake Air Temperature/Ambient Air Temperature Correlation P0128-00 - Thermostat Rationality P0234-00 - Turbocharger Overboost Condition P0420-00 - Catalyst Efficiency (Bank 1) P05F8-00 - Reductant Heater Control Module Performance P050E-00 - Cold Start Engine Exhaust Temperature Too Low P200A-00 - Intake Manifold Runner Performance - (Bank 1) P200B-00 - Intake Manifold Runner Performance - (Bank 2) P202E-00 - Reductant Injection Valve Circuit Performance P204F-00 - Reductant System Performance P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance P20BA-00 - Reductant Heater 1 Control Circuit Performance P20BE-00 - Reductant Pressure Line Heater Control Circuit Performance P20C2-00 - Reductant Heater 3 Control Circuit Performance P20E9-00 - Reductant Pressure Too High P225C-00 - NOX Sensor 1/1 Performance - Signal Stuck High |
| 18-045-14 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 This bulletin involves verifying the proper operation of the Diesel Exhaust Fluid (DEF) system and, if necessary, replacing the Selective Catalyst Reduction (SCR) Catalyst assembly. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find Diagnostic Trouble Code (DTC) P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 set in the Powertrain Control Module (PCM) memory.. |
| 18-028-14 REV. C | 2018-06-11. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on codes that have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P2459-00 - Diesel Particulate Filter Regeneration Frequency. ? P0133-00 - O2 Sensor 1/1 Slow Response. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). ? P0171-00 - Fuel System 1/1 Lean. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). ? P0045-00 - Turbocharger Boost Control Circuit/Open. ? P0087-00 - Fuel Rail Pressure Too Low. ? P009A-00 - Intake Air Temperature/Ambient Air Temperature Correlation. ? P0128-00 - Thermostat Rationality. ? P0234-00 - Turbocharger Overboost Condition. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P05F8-00 - Reductant Heater Control Module Performance. ? P050E-00 - Cold Start Engine Exhaust Temperature Too Low. ? P200A-00 - Intake Manifold Runner Performance - (Bank 1). ? P200B-00 - Intake Manifold Runner Performance - (Bank 2). ? P202E-00 - Reductant Injection Valve Circuit Performance. ? P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. ? P204F-00 - Reductant System Performance. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P20BA-00 - Reductant Heater 1 Control Circuit Performance. ? P20BE-00 - Reductant Pressure Line Heater Control Circuit Performance. ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P20E9-00 - Reductant Pressure Too High. |
| 18-054-14 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Intermittent Extended Crank, Long Crank Time. This bulletin involves inspecting the Bank 1 Camshaft Position Sensor serial number and if necessary, replacing the sensor. A small number of customers may experience an intermittent 1 to 5 second extended crank condition when starting their vehicle. No DTCs will be present when this occurs. |
| 18-028-14 REV. B | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on codes that have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P2459-00 - Diesel Particulate Filter Regeneration Frequency. ? P0133-00 - O2 Sensor 1/1 Slow Response. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). ? P0171-00 - Fuel System 1/1 Lean. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). ? P0045-00 - Turbocharger Boost Control Circuit/Open. ? P0087-00 - Fuel Rail Pressure Too Low. ? P009A-00 - Intake Air Temperature/Ambient Air Temperature Correlation. ? P0128-00 - Thermostat Rationality. ? P0234-00 - Turbocharger Overboost Condition. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P05F8-00 - Reductant Heater Control Module Performance. ? P050E-00 - Cold Start Engine Exhaust Temperature Too Low. ? P200A-00 - Intake Manifold Runner Performance - (Bank 1). ? P200B-00 - Intake Manifold Runner Performance - (Bank 2). ? P202E-00 - Reductant Injection Valve Circuit Performance. ? P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. ? P204F-00 - Reductant System Performance. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P20BA-00 - Reductant Heater 1 Control Circuit Performance. ? P20BE-00 - Reductant Pressure Line Heater Control Circuit Performance. ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P20E9-00 - Reductant Pressure Too High. |
| 21-025-14 | 2018-06-11. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; ENGINE AND ENGINE COOLING. Vehicle Remains in First Gear Too Long After Engine Restarts With Stop/Start Feature This bulletin involves flash reprogramming of the Transmission Control Module (TCM) with new software. Customers may indicate that the vehicle remains in first gear too long after the engine restarts with the Stop/Start feature. |
| 18-034-14 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit |
| 18-028-14 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? ? P0045-00 - TURBOCHARGER BOOST CONTROL CIRCUIT/OPEN ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0128-00 - THERMOSTAT RATIONALITY ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P05F8-00 - REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20BE-00 - REDUCTANT PRESSURE LINE HEATER CONTROL CIRCUIT PERFORMANCE ? P20C2-00 - REDUCTANT HEATER 3 CONTROL CIRCUIT PERFORMANCE ? P20E9-00 - REDUCTANT PRESSURE TOO HIGH ? P20EE-00 - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P225C-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK HIGH ? P225D-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK LOW ? P2453-00 - DIESEL PARTICULATE FILTER DIFFERENTIAL PRESSURE SENSOR CIRCUIT PERFORMANCE ? P249C-00 - EXCESSIVE TIME TO ENTER CLOSED LOOP REDUCTANT INJECTION CONTROL ? P24C2-00 - EXHAUST GAS TEMPERATURE MEASUREMENT SYSTEM - MULTIPLE SENSOR CORRELATION BANK 1 ? P24F2-00 - EGR TEMPERATURE/CHARGE AIR COOLER TEMPERATURE CORRELATION ? P2564-00 - TURBOCHARGER POSITION SENSOR C |
| R69 | 2018-06-04. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. Emissions Recall R69 Selective Catalytic Reduction Catalyst Effective immediately all repairs on involved vehicles are to be performed according to this recall. Service Bulletin 18-064-15 is no longer applicable for vehicles involved in this recall. Those vehicles that have already had this repair performed, as determined by our warranty records, have been excluded from this recall. The Selective Catalytic Reduction (SCR) catalyst on about 11,400 of the above vehicles is experiencing washcoat degradation, which may lead to the exceedance of exhaust emission standards. |
| 09-004-17 | 2018-06-04. Service bulletin. ENGINE AND ENGINE COOLING. Intermittent Engine Shudder While Driving This bulletin involves replacing the engine cylinder heads.A small number of customers may experience a slight engine shudder while driving. They may state that the condition feels and sounds like driving over rumble strips. It may also be perceived as an internal transmission issue or engine misfire. No Diagnostic Trouble Codes (DTCs) will set as a result of this condition. |
| 18-028-14 REV. A | 2018-05-21. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING:COOLING SYSTEM. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? ? P0045-00 - TURBOCHARGER BOOST CONTROL CIRCUIT/OPEN ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0128-00 - THERMOSTAT RATIONALITY ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P05F8-00 - REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20BE-00 - REDUCTANT PRESSURE LINE HEATER CONTROL CIRCUIT PERFORMANCE ? P20C2-00 - REDUCTANT HEATER 3 CONTROL CIRCUIT PERFORMANCE ? P20E9-00 - REDUCTANT PRESSURE TOO HIGH ? P20EE-00 - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P225C-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK HIGH ? P225D-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK LOW ? P2453-00 - DIESEL PARTICULATE FILTER DIFFERENTIAL PRESSURE SENSOR CIRCUIT PERFORMANCE ? P249C-00 - EXCESSIVE TIME TO ENTER CLOSED LOOP REDUCTANT INJECTION CONTROL ? P24C2-00 - EXHAUST GAS TEMPERATURE MEASUREMENT SYSTEM - MULTIPLE SENSOR CORRELATION BANK 1 ? P24F2-00 - EGR TEMPERATURE/CHARGE AIR COOLER TEMPERATURE CORRELATION ? P2564-00 - TURBOCHARGER POSITION SENSOR C |
| RL108213A$ | 2017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~ |
| 9003633 | 2017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. Water Pump Dealers are replacing water pumps because of a coolant leak. Water pumps are found TNF but the water pump bypass o-ring was pinched resulting in a coolant leak that looks like a failed pump. Please inspect the bypass o-ring before replacing the pump as it is available separate for service. |
| 9003355 | 2017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. 3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair. |
| 52029737A$ | 2017-11-03. Service bulletin. FUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER. TANK, Diesel Exhaust Fluid, Part Includes Temp Sensor and Level Sensor For DS and WK vehicles ONLY; If the urea tank is being replaced due to P249C or P203E on a 2014-2016 model year 3.0L Turbo Diesel (EXF) on DS or WK, please call Indra Djutrisno at cell (248) 892-3473. If no response is received within 15 minutes, please continue with repair.~ |
| 68141352A$ | 2017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. 3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.