WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Ram 1500

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

615 on file from NHTSA, as of 2026-10-19.

About P204F on the 2014 Ram 1500: what the code means, and the bulletins and recalls about the same components.

By type

By component

By trouble code

Only bulletins with trouble code: P204F are shown. Show all

Bulletins, newest first
1802814REVD2022-09-26. Service bulletin. FUEL SYSTEM, GASOLINE; SERVICE BRAKES, HYDRAULIC; EXTERIOR LIGHTING; SUSPENSION; FUEL SYSTEM, DIESEL; BACK OVER PREVENTION; ELECTRICAL SYSTEM. Flash: MIL Illumination - Diagnostic and System Improvements Bulletin involves reprogramming the Powertrain Control Module (PCM) with latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary, depending on Diagnostic Trouble Codes (DTC) that may have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC) other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which technician may find one or more of following DTCs have been set: P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel Ratio Control. P2459-00 - Diesel Particulate Filter Regeneration Frequency. P0133-00 - O2 Sensor 1/1 Slow Response. P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). P0171-00 - Fuel System 1/1 Lean. P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). P0045-00 - Turbocharger Boost Control Circuit/Open. P0087-00 - Fuel Rail Pressure Too Low. P009A-00 - Intake Air Temperature/Ambient Air Temperature Correlation. P0128-00 - Thermostat Rationality. P0234-00 - Turbocharger Overboost Condition. P0420-00 - Catalyst Efficiency (Bank 1). P05F8-00 - Reductant Heater Control Module Performance. P050E-00 - Cold Start Engine Exhaust Temperature Too Low. P200A-00 - Intake Manifold Runner Performance - (Bank 1). P200B-00 - Intake Manifold Runner Performance - (Bank 2). P202E-00 - Reductant Injection Valve Circuit Performance. P204F-00 - Reductant System Performance. P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. P20BA-00 - Reductant Heater 1 Control Circuit Performance. P20BE-00 - Reductant Pressure Line Heater Control Circuit Performance. P20C2-00 - Reductant Heater 3 Control Circuit Performance. P20E9-00 - Reductant Pressure Too High. P225C-00 - NOX Sensor 1/1 Performance - Signal Stuck High.
18-028-142022-08-29. Service bulletin. FUEL SYSTEM, GASOLINE; POWER TRAIN; ELECTRICAL SYSTEM. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? ? P0045-00 - TURBOCHARGER BOOST CONTROL CIRCUIT/OPEN ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0128-00 - THERMOSTAT RATIONALITY ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P05F8-00 - REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20BE-00 - REDUCTANT PRESSURE LINE HEATER CONTROL CIRCUIT PERFORMANCE ? P20C2-00 - REDUCTANT HEATER 3 CONTROL CIRCUIT PERFORMANCE ? P20E9-00 - REDUCTANT PRESSURE TOO HIGH ? P20EE-00 - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P225C-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK HIGH ? P225D-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK LOW ? P2453-00 - DIESEL PARTICULATE FILTER DIFFERENTIAL PRESSURE SENSOR CIRCUIT PERFORMANCE ? P249C-00 - EXCESSIVE TIME TO ENTER CLOSED LOOP REDUCTANT INJECTION CONTROL ? P24C2-00 - EXHAUST GAS TEMPERATURE MEASUREMENT SYSTEM - MULTIPLE SENSOR CORRELATION BANK 1 ? P24F2-00 - EGR TEMPERATURE/CHARGE AIR COOLER TEMPERATURE CORRELATION ? P2564-00 - TURBOCHARGER POSITION SENSOR C
18-028-142022-08-22. Service bulletin. ELECTRICAL SYSTEM. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? ? P0045-00 - TURBOCHARGER BOOST CONTROL CIRCUIT/OPEN ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0128-00 - THERMOSTAT RATIONALITY ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P05F8-00 - REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20BE-00 - REDUCTANT PRESSURE LINE HEATER CONTROL CIRCUIT PERFORMANCE ? P20C2-00 - REDUCTANT HEATER 3 CONTROL CIRCUIT PERFORMANCE ? P20E9-00 - REDUCTANT PRESSURE TOO HIGH ? P20EE-00 - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P225C-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK HIGH ? P225D-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK LOW ? P2453-00 - DIESEL PARTICULATE FILTER DIFFERENTIAL PRESSURE SENSOR CIRCUIT PERFORMANCE ? P249C-00 - EXCESSIVE TIME TO ENTER CLOSED LOOP REDUCTANT INJECTION CONTROL ? P24C2-00 - EXHAUST GAS TEMPERATURE MEASUREMENT SYSTEM - MULTIPLE SENSOR CORRELATION BANK 1 ? P24F2-00 - EGR TEMPERATURE/CHARGE AIR COOLER TEMPERATURE CORRELATION ? P2564-00 - TURBOCHARGER POSITION SENSOR C
18-021-15 REV. E2022-08-08. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, DIESEL; BACK OVER PREVENTION; EXTERIOR LIGHTING; SERVICE BRAKES; FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. Flash: 3.0L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on Diagnostic Trouble Codes (DTC) that may have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P26AB-00 - Engine Coolant Bypass Valve Stuck. ? P24AF-00 - Particulate Matter Sensor Circuit Performance. ? P2196-00 - O2 Sensor 1/1 Stuck Rich. ? P1E0C-00 - Empty Fuel Tank. ? P2237-00 - O2 Sensor 1/1 Pump Cell Current Circuit Open. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P204F-00 - Reductant System Performance. ? P20E9-00 - Reductant Pressure Too High. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. ? P241D-00 - SCR Inducement - Forced Engine Shutdown. ? P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel Ratio Control. ? P2459-00 - Diesel Particulate Filter Regeneration Frequency. ? P0133-00 - O2 Sensor 1/1 Slow Response. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). ? P0171-00 - Fuel System 1/1 Lean. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). ? P0045-00 - Turbocharger Boost Control Circuit/Open. ? P0087-00 - Fuel Rail Pressure Too Low. ? P009A-
18-021-15 REV. E2022-07-25. Service bulletin. FUEL SYSTEM, DIESEL; POWER TRAIN:MANUAL TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE; SERVICE BRAKES, HYDRAULIC; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: 3.0L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on Diagnostic Trouble Codes (DTC) that may have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P26AB-00 - Engine Coolant Bypass Valve Stuck. ? P24AF-00 - Particulate Matter Sensor Circuit Performance. ? P2196-00 - O2 Sensor 1/1 Stuck Rich. ? P1E0C-00 - Empty Fuel Tank. ? P2237-00 - O2 Sensor 1/1 Pump Cell Current Circuit Open. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P204F-00 - Reductant System Performance. ? P20E9-00 - Reductant Pressure Too High. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. ? P241D-00 - SCR Inducement - Forced Engine Shutdown. ? P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel Ratio Control. ? P2459-00 - Diesel Particulate Filter Regeneration Frequency. ? P0133-00 - O2 Sensor 1/1 Slow Response. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). ? P0171-00 - Fuel System 1/1 Lean. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). ? P0045-00 - Turbocharger Boost Control Circuit/Open. ? P0087-00 - Fuel Rail Pressure Too Low. ? P009A-
18-021-15 REV F2019-05-20. Service bulletin. STRUCTURE; ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; SERVICE BRAKES, HYDRAULIC; FUEL SYSTEM, DIESEL. Flash: 3.0L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on Diagnostic Trouble Codes (DTCs) that may have set. A small number of customers may experience an intermittent engine shudder, bucking under hard acceleration, or vibration. In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P1296-00 - EGR Slow Response - Increasing Flow. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P24A4-00 - Particulate Filter Restriction - Soot Accumulation Too High. ? P24D1-00 - Particulate Matter Sensor Regeneration Incomplete. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P1289-00 - NOx Sensor 1/2 Zero Offset Too Low. ? P2463-00 - Diesel Particulate Filter - Soot Accumulation . ? U0422-00 - Implausible Data Received From Body Control Module. ? U3017-00 - Control Module Timer/Clock Performance. ? P26AB-00 - Engine Coolant Bypass Valve Stuck. ? P24AF-00 - Particulate Matter Sensor Circuit Performance. ? P2196-00 - O2 Sensor 1/1 Stuck Rich. ? P1E0C-00 - Empty Fuel Tank. ? P2237-00 - O2 Sensor 1/1 Pump Cell Current Circuit Open. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P204F-00 - Reductant System Performance. ? P20E9-00 - Reductant Pressure Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. ? P241D-00 - SCR Inducement - Forced Engine Shutdown. ? P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel
18-021-15 REV-E2018-12-17. Service bulletin. ENGINE. Flash: 3.0L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on Diagnostic Trouble Codes (DTC) that may have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P26AB-00 - Engine Coolant Bypass Valve Stuck. ? P24AF-00 - Particulate Matter Sensor Circuit Performance. ? P2196-00 - O2 Sensor 1/1 Stuck Rich. ? P1E0C-00 - Empty Fuel Tank. ? P2237-00 - O2 Sensor 1/1 Pump Cell Current Circuit Open. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P204F-00 - Reductant System Performance. ? P20E9-00 - Reductant Pressure Too High. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. ? P241D-00 - SCR Inducement - Forced Engine Shutdown. ? P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel Ratio Control. ? P2459-00 - Diesel Particulate Filter Regeneration Frequency. ? P0133-00 - O2 Sensor 1/1 Slow Response. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). ? P0171-00 - Fuel System 1/1 Lean. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). ? P0045-00 - Turbocharger Boost Control Circuit/Open. ? P0087-00 - Fuel Rail Pressure Too Low. ? P009A-
18-021-15 REVA2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. Flash: 3.0L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on Diagnostic Trouble Codes (DTC) that may have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P204F-00 - Reductant System Performance. ? P20E9-00 - Reductant Pressure Too High. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. ? P241D-00 - Scr Inducement - Forced Engine Shutdown. ? P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel Ratio Control. ? P2459-00 - Diesel Particulate Filter Regeneration Frequency. ? P0133-00 - O2 Sensor 1/1 Slow Response. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). ? P0171-00 - Fuel System 1/1 Lean. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). ? P0045-00 - Turbocharger Boost Control Circuit/Open. ? P0087-00 - Fuel Rail Pressure Too Low. ? P009A-00 - Intake Air Temperature/Ambient Air Temperature Correlation. ? P0128-00 - Thermostat Rationality. ? P0234-00 - Turbocharger Overboost Condition. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P05F8-00 - Reductant Heater Control Module Performance. ? P050E-00 - Cold Start Engine Exhaust Temperature Too Low. ? P200A-00 - Intake M
18-021-15 REV-D2018-11-19. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM; FUEL SYSTEM, DIESEL. Flash: 3.0L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on Diagnostic Trouble Codes (DTC) that may have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P26AB-00 - Engine Coolant Bypass Valve Stuck. ? P24AF-00 - Particulate Matter Sensor Circuit Performance. ? P2196-00 - O2 Sensor 1/1 Stuck Rich. ? P1E0C-00 - Empty Fuel Tank. ? P2237-00 - O2 Sensor 1/1 Pump Cell Current Circuit Open. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P204F-00 - Reductant System Performance. ? P20E9-00 - Reductant Pressure Too High. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. ? P241D-00 - Scr Inducement - Forced Engine Shutdown. ? P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel Ratio Control. ? P2459-00 - Diesel Particulate Filter Regeneration Frequency. ? P0133-00 - O2 Sensor 1/1 Slow Response. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). ? P0171-00 - Fuel System 1/1 Lean. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). ? P0045-00 - Turbocharger Boost Control Circuit/Open. ? P0087-00 - Fuel Rail Pressure Too Low. ? P009A-
18-021-152018-09-24. Service bulletin. FUEL SYSTEM, DIESEL; ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT. Flash: 3.0L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on Diagnostic Trouble Codes (DTC) that may have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P20C2 - Reductant Heater 3 Control Circuit Performance. ? P204F - Reductant System Performance. ? P20E9 - Reductant Pressure Too High. ? P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel Ratio Control. ? P2459-00 - Diesel Particulate Filter Regeneration Frequency. ? P0133-00 - O2 Sensor 1/1 Slow Response. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). ? P0171-00 - Fuel System 1/1 Lean. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). ? P0045-00 - Turbocharger Boost Control Circuit/Open. ? P0087-00 - Fuel Rail Pressure Too Low. ? P009A-00 - Intake Air Temperature/Ambient Air Temperature Correlation. ? P0128-00 - Thermostat Rationality. ? P0234-00 - Turbocharger Overboost Condition. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P05F8-00 - Reductant Heater Control Module Performance. ? P050E-00 - Cold Start Engine Exhaust Temperature Too Low. ? P200A-00 - Intake Manifold Runner Performance - (Bank 1). ? P200B-00 - Intake Manifold Runner Performance - (Bank 2). ? P202E-00 - Reductant Injection Valve Circuit Performance. ? P204F-00 - Reductant System Performance. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P20BA-00 - Reductant Heater 1 Control Circuit Performance. ? P20BE-00 -
18-028-14 REV. D2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on Diagnostic Trouble Codes (DTC) that may have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: P016A-00 - Excessive Time To Enter Closed Loop Air/Fuel Ratio Control. P2459-00 - Diesel Particulate Filter Regeneration Frequency P0133-00 - O2 Sensor 1/1 Slow Response P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2) P0171-00 - Fuel System 1/1 Lean P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1) P0045-00 - Turbocharger Boost Control Circuit/Open P0087-00 - Fuel Rail Pressure Too Low P009A-00 - Intake Air Temperature/Ambient Air Temperature Correlation P0128-00 - Thermostat Rationality P0234-00 - Turbocharger Overboost Condition P0420-00 - Catalyst Efficiency (Bank 1) P05F8-00 - Reductant Heater Control Module Performance P050E-00 - Cold Start Engine Exhaust Temperature Too Low P200A-00 - Intake Manifold Runner Performance - (Bank 1) P200B-00 - Intake Manifold Runner Performance - (Bank 2) P202E-00 - Reductant Injection Valve Circuit Performance P204F-00 - Reductant System Performance P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance P20BA-00 - Reductant Heater 1 Control Circuit Performance P20BE-00 - Reductant Pressure Line Heater Control Circuit Performance P20C2-00 - Reductant Heater 3 Control Circuit Performance P20E9-00 - Reductant Pressure Too High P225C-00 - NOX Sensor 1/1 Performance - Signal Stuck High
18-028-14 REV. C2018-06-11. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on codes that have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P2459-00 - Diesel Particulate Filter Regeneration Frequency. ? P0133-00 - O2 Sensor 1/1 Slow Response. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). ? P0171-00 - Fuel System 1/1 Lean. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). ? P0045-00 - Turbocharger Boost Control Circuit/Open. ? P0087-00 - Fuel Rail Pressure Too Low. ? P009A-00 - Intake Air Temperature/Ambient Air Temperature Correlation. ? P0128-00 - Thermostat Rationality. ? P0234-00 - Turbocharger Overboost Condition. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P05F8-00 - Reductant Heater Control Module Performance. ? P050E-00 - Cold Start Engine Exhaust Temperature Too Low. ? P200A-00 - Intake Manifold Runner Performance - (Bank 1). ? P200B-00 - Intake Manifold Runner Performance - (Bank 2). ? P202E-00 - Reductant Injection Valve Circuit Performance. ? P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. ? P204F-00 - Reductant System Performance. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P20BA-00 - Reductant Heater 1 Control Circuit Performance. ? P20BE-00 - Reductant Pressure Line Heater Control Circuit Performance. ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P20E9-00 - Reductant Pressure Too High.
18-028-14 REV. B2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. It also involves replacement of the Oxygen (O2) Sensor and cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 if necessary depending on codes that have set. A small number of customers may experience an intermittent engine shudder or vibration which may not set a Diagnostic Trouble Code (DTC). In addition other customers may experience a Malfunction Indicator Lamp (MIL) illumination upon which the technician may find one or more of the following DTCs have been set: ? P2459-00 - Diesel Particulate Filter Regeneration Frequency. ? P0133-00 - O2 Sensor 1/1 Slow Response. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance - (1/2). ? P0171-00 - Fuel System 1/1 Lean. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance (1/1). ? P0045-00 - Turbocharger Boost Control Circuit/Open. ? P0087-00 - Fuel Rail Pressure Too Low. ? P009A-00 - Intake Air Temperature/Ambient Air Temperature Correlation. ? P0128-00 - Thermostat Rationality. ? P0234-00 - Turbocharger Overboost Condition. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P05F8-00 - Reductant Heater Control Module Performance. ? P050E-00 - Cold Start Engine Exhaust Temperature Too Low. ? P200A-00 - Intake Manifold Runner Performance - (Bank 1). ? P200B-00 - Intake Manifold Runner Performance - (Bank 2). ? P202E-00 - Reductant Injection Valve Circuit Performance. ? P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. ? P204F-00 - Reductant System Performance. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P20BA-00 - Reductant Heater 1 Control Circuit Performance. ? P20BE-00 - Reductant Pressure Line Heater Control Circuit Performance. ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P20E9-00 - Reductant Pressure Too High.
18-028-142018-06-11. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? ? P0045-00 - TURBOCHARGER BOOST CONTROL CIRCUIT/OPEN ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0128-00 - THERMOSTAT RATIONALITY ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P05F8-00 - REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20BE-00 - REDUCTANT PRESSURE LINE HEATER CONTROL CIRCUIT PERFORMANCE ? P20C2-00 - REDUCTANT HEATER 3 CONTROL CIRCUIT PERFORMANCE ? P20E9-00 - REDUCTANT PRESSURE TOO HIGH ? P20EE-00 - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P225C-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK HIGH ? P225D-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK LOW ? P2453-00 - DIESEL PARTICULATE FILTER DIFFERENTIAL PRESSURE SENSOR CIRCUIT PERFORMANCE ? P249C-00 - EXCESSIVE TIME TO ENTER CLOSED LOOP REDUCTANT INJECTION CONTROL ? P24C2-00 - EXHAUST GAS TEMPERATURE MEASUREMENT SYSTEM - MULTIPLE SENSOR CORRELATION BANK 1 ? P24F2-00 - EGR TEMPERATURE/CHARGE AIR COOLER TEMPERATURE CORRELATION ? P2564-00 - TURBOCHARGER POSITION SENSOR C
18-028-14 REV. A2018-05-21. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING:COOLING SYSTEM. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? ? P0045-00 - TURBOCHARGER BOOST CONTROL CIRCUIT/OPEN ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0128-00 - THERMOSTAT RATIONALITY ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P05F8-00 - REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20BE-00 - REDUCTANT PRESSURE LINE HEATER CONTROL CIRCUIT PERFORMANCE ? P20C2-00 - REDUCTANT HEATER 3 CONTROL CIRCUIT PERFORMANCE ? P20E9-00 - REDUCTANT PRESSURE TOO HIGH ? P20EE-00 - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P225C-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK HIGH ? P225D-00 - NOX SENSOR 1/1 PERFORMANCE - SIGNAL STUCK LOW ? P2453-00 - DIESEL PARTICULATE FILTER DIFFERENTIAL PRESSURE SENSOR CIRCUIT PERFORMANCE ? P249C-00 - EXCESSIVE TIME TO ENTER CLOSED LOOP REDUCTANT INJECTION CONTROL ? P24C2-00 - EXHAUST GAS TEMPERATURE MEASUREMENT SYSTEM - MULTIPLE SENSOR CORRELATION BANK 1 ? P24F2-00 - EGR TEMPERATURE/CHARGE AIR COOLER TEMPERATURE CORRELATION ? P2564-00 - TURBOCHARGER POSITION SENSOR C

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.