WenmarOpen by Wenmar Pro

Service bulletins for the 2016 Nissan Titan

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

304 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
NTB20-0572020-09-11. Service bulletin. EQUIPMENT:MECHANICAL; ENGINE AND ENGINE COOLING. VK56 CONNECTING ROD CAP BOLT SERVICE INFORMATION SERVICE INFORMATION A change has been made to the connecting rod cap bolt service part. The new service part (B in Figure 1) is visually different, but is a direct replacement for the original equipment part. IMPORTANT: See page 2 for the procedure to inspect the cap bolt service part for excessive stretch. If replacement of a single connecting rod cap bolt is indicated for any given connecting rod, both connecting rod cap bolts of the affected connecting rod must be replaced as a set.
NTB19-037a2020-08-09. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. 2016-2019 TITAN; MIL ON WITH DTC P0448 AND WATER IN EVAP FILTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
PC731 2016-17 TI2020-05-06. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING:ENGINE:DIESEL. On-Board Diagnostic (OBD) Electronic Control Unit (ECU) Voluntary Emission Recall Campaign ***** Campaign Summary ***** Nissan is conducting a Voluntary Emissions Recall Campaign on 27,085 certain MY2016-17 Titan Diesel vehicles identified in Service Comm to inspect and, if necessary, reprogram the Electronic Control Unit (ECU) with countermeasure software. Nissan has determined that the subject vehicles were manufactured with an On-Board Diagnostic (OBD) calibration that may not allow the exhaust gas sensor monitors to run as intended. If an affected vehicle is not repaired, the exhaust gas sensor monitors may not run as frequently as required by regulation to determine if the sensor is performing as intended. This issue has no effect on vehicle safety, fuel economy, drivability, or performance. ***** What Dealers Should Do**** 1. Verify campaign applicability using Service Comm or DBS National Service History – Open Campaign I.D. PC731. 2. Dealers should use NTB20-030 to correct any vehicles subject to this campaign. 3. Once repaired, dealers should submit the claim, using the claims coding provided, and release the vehicle.
NTB20-0302020-05-05. Service bulletin. ENGINE AND ENGINE COOLING. VOLUNTARY EMISSIONS RECALL CAMPAIGN 2016-2017 TITAN XD WITH DIESEL ENGINE; ENGINE CONTROL MODULE INTRODUCTION Nissan is conducting this voluntary emissions recall campaign on certain specific model year 2016-2017 Titan XD vehicles equipped with a diesel engine. The Engine Control Module (ECM) will be inspected, and reprogrammed if it applies. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PC731 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealer’s responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary emissions recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealer’s inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a emissions recall must be corrected prior to sale. Failure to do so can result in civil penalties and/or fines by the Environmental Protection Agency. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.
NTB19-011a2020-03-07. Service bulletin. ENGINE. 2016 – 2019 TITAN XD; MIL ON WITH DTC P2048 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB14-012e2019-10-09. Service bulletin. ENGINE AND ENGINE COOLING. REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-053a2019-06-24. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN. 2016-2017 TITAN/TITAN XD; FAN COUPLING TICK / KNOCK IN COLD AMBIENT TEMPERATURES (32°F (0°C) OR BELOW) This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB19-0372019-05-20. Service bulletin. ENGINE. 2016-2019 TITAN; MIL ON WITH DTC P0448 AND WATER IN EVAP FILTER IF YOU CONFIRM The MIL is ON with DTC P0448 (EVAP canister vent control valve close) stored in the ECM and water is found in the EVAP filter, canister, or vent control valve ACTION Remove and replace the: - Fuel filler tube. - EVAP filter. - EVAP canister. - EVAP vent control valve. - EVAP pressure sensor. IMPORTANT: Before any parts are removed from the vehicle, note the EVAP filter orientation and hose routing (take a photo). Hose routing and EVAP filter orientation is critical and varies depending on production date.
NTB16-037e2019-03-25. Service bulletin. ENGINE. 2016 TITAN XD; MIL ON WITH ENGINE DTCs STORED AND/OR IDLE FLUCTUATION This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NTB19-0112019-03-18. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; FUEL SYSTEM, GASOLINE. 2016 ? 2018 TITAN XD; MIL ON WITH DTC P2048 STORED This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM The MIL is ON and DTC P2048 (REDUCTANT INJECTION VALVE CIRCUIT LOW 1/1) is stored. ACTION Reprogram the ECM per the SERVICE PROCEDURE in this bulletin. - Refer to SERVICE PROCEDURE on the next page to confirm if reprogramming is needed. - Save Computer Data with CONSULT-III plus (C-III plus). - If this bulletin applies, continue with ECM Reprogramming procedure. - Write Saved Data with CONSULT-III plus.
NTB19-0102019-02-19. Service bulletin. ENGINE; FUEL SYSTEM, DIESEL. 2016 - 2018 TITAN XD; DEF SYSTEM PARTS AVAILABILITY This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 diesel engine. SERVICE INFORMATION When diagnosing any Diesel Exhaust Fluid (DEF) system component, refer to Table A below. These parts are now available separately. Do not replace the entire DEF tank assembly if the required part is shown in Table A.
NTB19-0072019-02-19. Service bulletin. FUEL SYSTEM, DIESEL; ENGINE. 2016-2019 TITAN XD DIESEL; FUEL FILTER MAINTENANCE This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 diesel engine. SERVICE INFORMATION The Stage 1 and Stage 2 fuel filters must be replaced every 10,000 miles or a restriction may develop. DTCs P008A, P00C6, P0087 and/or a whining noise from the Stage 1 Fuel Filter Module may be present due to a restriction in the Stage 1 and/or Stage 2 fuel filters. NOTE: An inoperable or whining Stage 1 Fuel Filter Module that has not had the fuel filters regularly replaced as per the Owner?s Manual Maintenance schedule is not a warrantable repair. Before proceeding with any fuel system restriction diagnosis: - Confirm that both of the vehicle?s Stage 1 and Stage 2 fuel filters have been replaced at the correct service intervals, as per the Owner?s Manual Maintenance schedule. IMPORTANT: Warranty claim submissions for a Stage 1 Fuel Filter module will be denied if the Stage 1 and/or Stage 2 fuel filters have not been replaced per the Owner's Manual maintenance schedule.
NTB17-082b2019-02-19. Service bulletin. ENGINE AND ENGINE COOLING. NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
Revision 1-NEVAP2019-01-07. Service bulletin. EQUIPMENT; ENGINE. OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
NTB10-104c2018-08-20. Service bulletin. ENGINE. TITAN, ARMADA, NV; ENGINE OIL LEAK AT RIGHT SIDE BLOCK BALL PLUG This bulletin has been amended. The APPLIED VEHICLES section has been updated. No other changes have been made. Please discard all previous versions of this bulletin.
NTB18-046a2018-08-20. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN. 2016-2018 TITAN XD DIESEL; AIR CONDITIONING BLOWS HOT AIR AFTER EXTENDED IDLING OVER 100°F This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. This bulletin has been amended to change the Classification number. No other changes have been made. Please discard previous versions of this bulletin.
NTB18-0462018-08-06. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; EQUIPMENT:APPLIANCE:AIR CONDITIONER. 2016-2018 TITAN XD DIESEL; AIR CONDITIONING BLOWS HOT AIR AFTER EXTENDED IDLING OVER 100°F This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM Hot air starts to blow from the dash vents while the Air Conditioning is ON, under the following conditions: - After the engine has idled for an extended period with the vehicle in Drive (D-range). And - Ambient temperature outside the vehicle is 100°F (37.8°C) or more. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with the reprogramming procedure. 4. Write Saved Data with CONSULT-III plus.
NTB18-0462018-07-30. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT:APPLIANCE:AIR CONDITIONER. 2016-2018 TITAN XD DIESEL; AIR CONDITIONING BLOWS HOT AIR AFTER EXTENDED IDLING OVER 100°F This bulletin applies only to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM Hot air starts to blow from the dash vents while the Air Conditioning is ON, under the following conditions: - After the engine has idled for an extended period with the vehicle in Drive (D-range). And - Ambient temperature outside the vehicle is 100°F (37.8°C) or more. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with the reprogramming procedure. 4. Write Saved Data with CONSULT-III plus.
NTB18-0372018-06-18. Service bulletin. ENGINE. 2016 TITAN XD; MIL ON WITH DTC P0420 IF YOU CONFIRM The MIL is ?ON? with DTC P0420 (Catalyst System Efficiency Below Threshhold Bank 1), AND There are no drivability issues. ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming. 4. Write Saved Data with C-III plus.
NTB16-018c2018-05-21. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT; ENGINE AND ENGINE COOLING. MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin does NOT apply to Titan equipped with Cummins V8 Diesel engine. This bulletin has been amended to add a NOTE in the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.
NTB13-107b2018-04-23. Service bulletin. ENGINE. INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
NTB18-0242018-04-16. Service bulletin. ENGINE AND ENGINE COOLING. 2016-2018 TITAN XD; STAGE 1 AND STAGE 2 FUEL FILTER REPLACEMENT SERVICE INFORMATION When replacing the Stage 1 or Stage 2 fuel filters, it is important not to damage the new fuel filters, inner seals, or O-rings. Refer to the Service Procedure section of this bulletin or the Electronic Service Manual (ESM) ENGINE> FUEL SYSTEM> CUMMINS 5.0L> REMOVAL AND INSTALLATION to ensure the filters are being replaced correctly. P008A LOW FUEL PRESSURE CONTROL SYSTEM and/or a no start condition may occur if the procedure is not followed properly.
NTB18-0052018-04-02. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, DIESEL. 2016-2017 TITAN XD WITH CUMMINS 5.0L; IDLE FLUCTUATION DURING LOW TEMPERATURE WARM-UP This bulletin applies to vehicles equipped with a Cummins 5.0L V8 Diesel engine. IF YOU CONFIRM An applied vehicle?s idle fluctuates after starting when: - The coolant temperature is between 68°F (20°C) and 104°F (40°C) and - The vehicle is not moving (0 MPH). NOTE: This incident may continue until the coolant temperature reaches 104°F (40°C). ACTION 1. Save Computer Data with CONSULT-III plus (C-III plus). 2. At step 6 of the reprogramming procedure, confirm this bulletin applies to the vehicle you are working on. 3. If this bulletin applies, continue with reprogramming procedure. 4. Write Saved Data with CONSULT-III plus.
NTB17-1222018-01-29. Service bulletin. FUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING. 2016 ? 2017 TITAN XD DIESEL; BLOCK HEATER INOPERATIVE This bulletin applies to vehicles equipped with a Cummins (5.0L V8) Diesel engine only. IF YOU CONFIRM The coolant heater (block heater) needs to be replaced based on the Electronic Service Manual (ESM) inspection, and The vehicle is currently equipped with a coolant heater (with attached cord) located in the front engine cover. NOTE: - This bulletin does not apply if the vehicle is equipped with a coolant heater located in the water inlet at the lower radiator hose. - Refer to the ESM, section CO ? Engine Cooling System, for coolant heater operation and inspection information. ACTION 1. Use the Service Procedure in this bulletin to install a new coolant heater, locating it in the water inlet at the lower radiator hose. 2. Cut the cord to the original coolant heater.
NTB17-016e2017-12-22. Service bulletin. ENGINE AND ENGINE COOLING. ARMADA, TITAN AND TITAN XD; SHIFT SHOCK, LACK OF POWER, AND/OR RPM FLUCTUATES This bulletin applies to vehicles with a gasoline V8 engine only. This bulletin has been amended to add Armada to the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.