WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Nissan Murano

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

281 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
NTB16-0282021-05-24. Service bulletin. STRUCTURE:BODY:DOOR:HANDLE:EXTERIOR; ELECTRICAL SYSTEM; EQUIPMENT. Intelligent key buttons inoperative
NTB16-0252021-05-24. Service bulletin. AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION. Air Bag Diagnosis sensor unit coinfiguration
NTB16-0232021-05-24. Service bulletin. STEERING; EQUIPMENT. Nissan; Power steering noise heard inside vehicle with windows closed
NTB15-073B2021-05-24. Service bulletin. STRUCTURE:BODY:DOOR; ELECTRICAL SYSTEM. 2015-2016 Murano; Automatic back door does not operate and related DTCs
NTB15-044B2021-05-24. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP. Fuel Filler Cap tether clip service information
NTB15-039A2021-05-24. Service bulletin. LATCHES/LOCKS/LINKAGES:DOORS:LATCH; STRUCTURE:BODY:DOOR. 2015-2016 Murano; Side Door will not open or side door will not latch
NTB15-015e2021-05-24. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT. Pathfinder, Quest, Murano, Maxima, Altima V6, CVT Judder and DTC P17F0 or P17F1 Stored
NTB15-014B2021-05-24. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT. Enhanced Diagnostic Logic for CVT Judder
NTB15-013B2021-05-24. Service bulletin. POWER TRAIN. Nissan; Procedure to clean CVT Transmission fluid coolers
NTB14-084C2021-05-24. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. 2-Sensor occupant classification System Diagnostics and Information
NTB12-103C2021-05-24. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT. CVT/TDCM Calibration Data "Write" Procedure
NTB16028A2021-05-10. Service bulletin. ELECTRICAL SYSTEM; LATCHES/LOCKS/LINKAGES. SERVICE INFORMATION If it appears, for any or all of the Intelligent Keys on an applied vehicle, that all "RKE" lock/unlock/panic/trunk button functions of that specific Intelligent Key(s) does not work BUT The doors will lock and unlock when pressing either front door request switch while using the particular Intelligent Key(s) (see Figure 1 below), THEN That specific Intelligent Key may have become de-synchronized with the vehicle. NOTE: - Intelligent Key de-synchronization may occur if the Intelligent Key is not used for extended periods of time or if the Intelligent Key was not operating due to low battery condition and the battery has been replaced. - Do NOT replace the BCM, Intelligent Key, or any other parts if an Intelligent Key only needs to be re-synchronized. See this bulletin for further detail.
NTB12103D2021-05-10. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. SERVICE INFORMATION The Service Procedure (starting on page 2) in this bulletin contains the steps to perform TCM Calibration Data Write Procedures. These procedures are used when a complete CVT is replaced, or a CVT control valve (valve body) is replaced, or a Transmission Control Module (TCM) is replaced. See this bulletin for further detail.
NTB11027B2021-05-10. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; TIRES. SERVICE INFORMATION Temporary tire Flat Spotting is common on New Dealer In-Stock vehicles that have not been occasionally moved. Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90° (see Figure 1). Moving vehicles as shown will prevent tire Flat Spotting. See this bulletin for further detail.
NTB15013C2021-05-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT; POWER TRAIN; EQUIPMENT. IMPORTANT: Metal debris and friction material may become trapped in the radiator, cooling hoses, bypass valve or external CVT fluid cooler. This debris can contaminate the newly serviced transmission, control valve or torque converter. In severe cases this debris can block or restrict flow and may cause damage to the newly serviced CVT. SERVICE INFORMATION When a CVT, control valve or torque converter replacement is necessary for one of the applied vehicles, the CVT transmission fluid coolers (radiator based fluid cooler and external auxiliary cooler if present) must be flushed. Please see this bulletin for further details.
NTB15015F2021-05-10. Service bulletin. POWER TRAIN; EQUIPMENT ADAPTIVE/MOBILITY. IF YOU CONFIRM: The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration) AND One of these DTCs is stored: - P17F0 (CVT_JUDDER (T/M INSPECTION)) - P17F1 (CVT_JUDDER (C/U INSPECTION)) NOTE - If a transmission judder (as described above) is not reported, this bulletin does not apply. - If either P17F0 or P17F1 are not stored, this bulletin does not apply. - NTB15-014, Enhanced Diagnostic Logic For CVT Judder, has reprogramming instructions that may apply. ACTIONS: Perform the SERVICE PROCEDURE, starting on page 3. - Review the Repair Flow Chart in this bulletin. NOTE: Essential Tool Tech Cam (borescope) J-51951 has been sent to dealers. This tool?s attachments make CVTinspection possible. See this bulletin for further detail.
NTB09099A2021-05-10. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; EQUIPMENT ADAPTIVE/MOBILITY. IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
NTB09131B2021-05-10. Service bulletin. FORWARD COLLISION AVOIDANCE; EQUIPMENT:OTHER:LABELS. SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
NTB15014B2021-05-10. Service bulletin. EQUIPMENT; POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT; POWER TRAIN. IF YOU CONFIRM The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration). NOTE: A new diagnostic logic has been established to enhance the diagnostic process by storing diagnostic trouble codes (DTCs) on Applied Vehicles. The new DTCs are: P17F1 (CVT_JUDDER [C/U INSPECTION]) P17F0 (CVT_JUDDER [T/M INSPECTION]) ACTION 1. Refer to page 4, step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. NOTE:The current TCM Part Numbers in this bulletin have been updated. The vehicle you are working on may require reprogramming per this bulletin again. 2. If this bulletin applies, reprogram the TCM (Transmission Control Module) See this bulletin for further detail.
NTB160342021-05-10. Service bulletin. SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER; ELECTRICAL SYSTEM:SEAT HEATER:WIRING HARNESS; EQUIPMENT. IF YOU CONFIRM A buzz noise coming from: - The driver seat when the driver seat climate control heater is turned ON. and/or - The passenger seat when the passenger seat climate control heater is turned ON. ACTION Replace the climate controlled seat control unit. - Replace the control unit only for the seat that is making the buzz noise. - Refer to the Electronic Service Manual (ESM), section SE-Seat, for replacement information. See this bulletin for further information.
NTB15044B2021-05-10. Service bulletin. EQUIPMENT; FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP. SERVICE INFORMATION If the clip for the fuel filler cap tether becomes lost or is detached for any reason, it is no longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.
NTB15073B2021-05-10. Service bulletin. EQUIPMENT; VEHICLE SPEED CONTROL; ELECTRICAL SYSTEM; BACK OVER PREVENTION. IF YOU CONFIRM The automatic back door does not operate and/or one or a combination of the following DTCs are found stored in the Automatic Back Door Control Module (ABD CU): - B2426-29 (SPINDLE SENSOR LH) - B2427-29 (SPINDLE SENSOR RH) - B2416-1E (TOUCH SEN R OPEN) - B2417-1E (TOUCH SEN L OPEN) - B242A-13 (CLSR CONDITION) ACTION 1. Check the battery voltage (engine not running). - Make sure battery voltage is between 12 and 15.5 volts. - Charge or replace the battery as needed. 2. For 2015 Murano Only: Refer to page 9, step 13 in the Service Procedure to confirm if ABD CU reprogramming is needed. - Reprogram the ABD CU, if needed. - If the ABD CU is reprogramed, also perform Automatic Back Door Manual Configuration. 3. Perform Automatic Back Door Calibration (see page 22). 4. Erase all DTCs. 5. For 2015 Murano Only: If reprogramming was done, inform the customer of changes in automatic back door operation (see page 3, and also Owner?s Manual pages at the end of this bulletin. See this bulletin for further detail.
NTB160252021-05-10. Service bulletin. EQUIPMENT; BACK OVER PREVENTION; ELECTRICAL SYSTEM. SERVICE INFORMATION If an Air Bag Diagnosis Sensor Unit is replaced and the configuration of the old unit could not be saved, use the Service Procedure in this bulletin to: - Load the VIN specific configuration file from your electronic parts catalog (FAST or equivalent) onto a portable USB storage device (thumb drive) - Plug the thumb drive into your CONSULT PC. - Configure the new Air Bag Diagnosis Sensor Unit using the file that you loaded onto the thumb drive. See this bulletin for further detail.
NTB160232021-05-10. Service bulletin. ELECTRICAL SYSTEM; WHEELS; VISIBILITY; ENGINE AND ENGINE COOLING; POWER TRAIN; FUEL SYSTEM, GASOLINE; STEERING; BACK OVER PREVENTION. IF YOU CONFIRM A customer concern of while turning the steering wheel or when driving at low speed (straight or turning), a high pitch power steering noise can be heard. * Only while seated inside the vehicle And * With all of the windows up NOTE: If the audio and/or HVAC systems are turned ON it may be difficult to hear this issue. ACTION Install an Insulator onto the end of the power steering pump motor housing with the Service Procedure starting on the next page. Please see this bulletin for further details.
NTB15039A2021-05-10. Service bulletin. EQUIPMENT. IF YOU CONFIRM: The following incident, or the customer reports this incident: The vehicle has been parked (not running) in below freezing temperatures for an extended period (such as overnight). Then The Intelligent Key, key fob, or mechanical key is used to perform door unlock. Then When attempting to open the door, the door will not open (using either outside or inside handle, or both), or the door will open, but will not latch when closed. Then The door lock and latch functions normallywhen the vehicle has warmed up (vehicle left in the sun, moved indoors, or driven for several minutes). NOTE: The above incident, if it should occur, could be confirmed or reported for one or more of the four side doors. ACTION: Refer to the REPAIR FLOW CHART on page 2. See this bulletin for further detail.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.