Service bulletin NTB16-025

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10194201
Published by NHTSA	2021-05-24
Manufacturer's number	NTB16-025
Manufacturer's date	2016-03-10
NHTSA component	AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION

NHTSA's summary

Air Bag Diagnosis sensor unit coinfiguration

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Air bags

Vehicles listed
NISSAN MAXIMA	2016
NISSAN MURANO	2015, 2016
NISSAN ROGUE	2014, 2015, 2016

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
16V911000	2016-12-19. AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION
2016630	2016-12-15. Airbag
16V244000	2016-04-26. AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
NTB19-071D	2024-10-22. Service bulletin. DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)
NTB19-071C	2023-04-10. Service bulletin. DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071B	2022-06-03. Service bulletin. DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB16-046	2021-05-24. Service bulletin. Occupant Clfassification System Light Operation Logic Change
NTB14-100B	2021-05-24. Service bulletin. 2014 Rogue; Configuring the Air Bag Diagnostic sensor Unit
NTB16046	2021-05-10. Service bulletin. SERVICE INFORMATION Nissan is issuing this Technical Service Bulletin to clarify that a change has been made for the logic that controls the Occupant Classification System (OCS) and 'passenger airbag indicator' (PABI), as described in the Owner?s Manual. This TSB applies only to vehicles using the 2-sensor OCS. Those changes are: * PABI light is ON with an empty front passenger seat. Please see this bulletin for further details.
NTB00042D	2021-05-10. Service bulletin. SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
NTB08055C	2021-05-10. Service bulletin. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
NTB19-071A	2021-04-13. Service bulletin. DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB19-071	2019-10-09. Service bulletin. DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. • Refer to SERVICE PROCEDURE on page 5. HINT: “OCS” may also be referred to as “ODS”. 2. Perform “75-zero RESET”.