WenmarOpen by Wenmar Pro

Service bulletins for the 2010 Nissan Cube

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

83 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Equipment and accessories are shown. Show all

Bulletins, newest first
NTB11027B2021-05-10. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; TIRES. SERVICE INFORMATION Temporary tire Flat Spotting is common on New Dealer In-Stock vehicles that have not been occasionally moved. Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90° (see Figure 1). Moving vehicles as shown will prevent tire Flat Spotting. See this bulletin for further detail.
NTB09099A2021-05-10. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; EQUIPMENT ADAPTIVE/MOBILITY. IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
NTB09131B2021-05-10. Service bulletin. FORWARD COLLISION AVOIDANCE; EQUIPMENT:OTHER:LABELS. SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
NTB150602021-05-10. Service bulletin. SERVICE BRAKES; WHEELS; BACK OVER PREVENTION; STEERING; EQUIPMENT. SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
NTB99060G2021-05-10. Service bulletin. EQUIPMENT. SERVICE INFORMATION NOTE - Failure to follow the procedures in this bulletin may result in the denial of a warranty claim. In an effort to protect the paint finish, Paint Guard Film (PGF) is applied on many new Nissan vehicles. Paint Guard Film is a temporary white plastic protective film that is applied by the factory to the horizontal painted surfaces of the vehicle. The PGF protects the paint finish during vehicle handling, transportation and storage from harmful elements such as acid rain, iron particles, bird droppings, tree sap and other environmental contaminants. NOTE - Paint Guard Film CANNOT remain on the vehicle for more than six months after the vehicle's manufacture date. PGF must be removed at the end of six months. See this bulletin for further detail.
NTB00042D2021-05-10. Service bulletin. AIR BAGS; BACK OVER PREVENTION; EQUIPMENT. SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
NTB10066A2021-05-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
NTB08055C2021-05-10. Service bulletin. EQUIPMENT; AIR BAGS. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
NTB09020F2021-05-10. Service bulletin. FUEL/PROPULSION SYSTEM; EQUIPMENT. SERVICE INFORMATION If one or more of these EVAP leak DTCs are stored (P0442, P0455, P0456) on a 2007 through 2011 Nissan vehicle, a loose fuel fill cap may be the cause. Use the following resources to perform diagnostics and confirm the cause of stored DTCs. ASIST: - Appropriate Service Manual diagnostic procedures - Applicable Technical Service Bulletins (TSB). Leak Test: - With CONSULT-III plus - WORK SUPPORT >> EVAP SYSTEM CLOSE. NOTE: Use Essential Tool J-42909 or equivalent to pressurize the EVAP system. - With a "Smoke" leak detection machine. Refer to the machine's Operator's Manual for proper use. Make sure the customer is informed of the proper fuel filler cap installation.
NTB92123D2021-05-10. Service bulletin. WHEELS; EQUIPMENT. Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.
REV1-P8309_P83102019-04-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; AIR BAGS. Driver and Passenger Air Bag Inflator Field Quality Parts Collection Initiative UPDATE March 22, 2019 Please discard ealier versions of this bulletin. The announcement from August 3, 2018 has been revised to include: o This collection initiative has been expanded to include certain MY2009-10 370Z (Z34) vehicles in Zone A (Florida and Georgia) and Zone C (New York)
Revision 1-NEVAP2019-01-07. Service bulletin. EQUIPMENT; ENGINE. OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
NTB-11-0052011-03-03. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). NISSAN: NAVIGATION MAP DATA UPDATE MATRIX. AFFECTING ALL VEHICLES 2003-11 EXCEPT LEAF, EQUIPPED WITH NAVIGATION SYSTEM. CUSTOMER IS MAILED UPDATE DISC(S) OR SD CARD AND INSTALLS DATA; DEALERSHIP IS MAILED UPDATE DISC(S) AND THE DEALERSHIP INSTALLS DATA WHEN VEHICLE IS BROUGHT IN. *PE
NTB-09-1292010-04-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. NISSAN: VENT CONTROL VALVE REPLACEMENT. WHEN REPLACING THE EVAP CANISTER VENT CONTROL VALVE FOR REASON: USE THE ONE LISTED ON PAGE 2; FOR VENT CONTROL VALVE REPLACEMENT PROCEDURE, REFER TO THE APPROPRIATE SECTION OF THE ELECTRONIC SERVICE MANUALS (ESM; WHEN INSTALLING THE NEW VALVE, DO NOT ADD ANY LUBE TO ITS O RING; FOR FRONTIER (D40 SERIES) ONLY, INSTALL THE PROTECTOR LISTED IN PARTS INFORMATION. *PE INCLUDES 2005-09 FRONTIER. UPDATED 12/8/10. *PE

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.