WenmarOpen by Wenmar Pro

Service bulletins for the 2009 MINI Cooper

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

135 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
M2301082019-01-07. Service bulletin. POWER TRAIN. "MANUAL TRANSMISSION - STIFF DIAGONAL GEARSHIFT LEVER MOVEMENT. The customer may complain of a ""stiff diagonal shift"" (e.g., N-R, R-N, 2-3/3-2 or 4-5/5-4). Also, in some cases, gears cannot be selected, or the selector gear does not go into the neutral position. CAUSE 1. The deflection lever circlip of the gearshift mechanism is damaged or missing. 2. Possible corrosion at the gearshift mechanism (shift cables or transmission gearshift unit)"
M2101132018-12-03. Service bulletin. POWER TRAIN. Clutch Is Slipping or Grabbing. The customer states that the clutch is slipping or grabbing.
M2101142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; POWER TRAIN. Dual Mass Flywheel: Diagnosis and Inspection. INFORMATION The following three criteria must to be checked, evaluated and the resulting findings documented on the repair order prior to replacing a dual-mass flywheel as defective: 1. Total rotational angle at no load condition (with applied torque less then 20 Nm) 2. Secondary plate longitudal axial play 3. Friction surface appearance changes due to thermal overload. PROCEDURE Refer to the attached "Dual-mass Flywheel Inspection" document for the complete inspection procedure. The dual-mass flywheel replacement is justified only if one or more of the following criteria are met: 1. The total rotational free-play measured at the flywheel gear ring is: Equal to or greater than 3 tooth gaps on N14/N18-equipped engines; Equal to or greater than 14 tooth gaps on B38/B46/B48-equipped engines. 2. The secondary plate total axial bearing play measured at outside diameter of the flywheel is: Equal to or greater than 3 mm on N14/N18-equipped engines; Equal to or greater than 5 mm on B38/B46/B48-equipped engines. 3. Significant discoloration in the adjoining area outside the friction ring, or a severe ablation/erosion of the friction area, is present. WARRANTY INFORMATION Warranty claims for replacing a Dual Mass Flywheel are subject to denial or debit when it is determined that the diagnostic procedures outlined above were not followed. ATTACHMENTS View PDF attachment M210114_Dual-Mass_Flywheel_Inspection.
M1206152018-11-05. Service bulletin. POWER TRAIN. "ENGINE POWER REDUCTION WITH "CLUTCH DAMAGED"" FAULTS STORED This Service Information bulletin supersedes SI M12 06 15 dated July 2015. A drivetrain malfunction check control message is displayed, prompting the customer to contact the dealer for a service visit. F54, F55, F56, F57Target Integration level: F056-16-11-501 or higherThe vehicle drives normally, but fault(s) for a damaged clutch are stored in the DME. ? 1D3101 - Clutch: Damaged, transmittable torque too low ? 1D3201 - Clutch: Severely damaged, transmittable torque too low CAUSE 1. The DME software diagnostic for detecting excessive clutch slip is too sensitive. 2. The clutch is damaged."
M2401182018-04-23. Service bulletin. POWER TRAIN. AISIN AUTOMATIC TRANSMISISON: RIGHT SIDE OUTPUT SHAFT SEAL REPLACEMENT
SI-M-22-01-082009-11-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:MANUAL TRANSMISSION. MINI: A KNOCKING NOISE IS HEARD FROM THE FRONT OF VEHICLE DURING ENGINE LOAD REVERSALS, OR ON UNEVEN ROAD SURFACES. FASTENERS SECURING THE TRANSMISSION MOUNTING BRACKET TO THE BODY ARE NOT TIGHTENED TO THE REQUIRED SPECIFICATION. THE TRANSMISSION MOUNT IS DEFECTIVE. *PE

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.