WenmarOpen by Wenmar Pro

Service bulletins for the 2007 MINI Cooper

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

138 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
M2101142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; POWER TRAIN. Dual Mass Flywheel: Diagnosis and Inspection. INFORMATION The following three criteria must to be checked, evaluated and the resulting findings documented on the repair order prior to replacing a dual-mass flywheel as defective: 1. Total rotational angle at no load condition (with applied torque less then 20 Nm) 2. Secondary plate longitudal axial play 3. Friction surface appearance changes due to thermal overload. PROCEDURE Refer to the attached "Dual-mass Flywheel Inspection" document for the complete inspection procedure. The dual-mass flywheel replacement is justified only if one or more of the following criteria are met: 1. The total rotational free-play measured at the flywheel gear ring is: Equal to or greater than 3 tooth gaps on N14/N18-equipped engines; Equal to or greater than 14 tooth gaps on B38/B46/B48-equipped engines. 2. The secondary plate total axial bearing play measured at outside diameter of the flywheel is: Equal to or greater than 3 mm on N14/N18-equipped engines; Equal to or greater than 5 mm on B38/B46/B48-equipped engines. 3. Significant discoloration in the adjoining area outside the friction ring, or a severe ablation/erosion of the friction area, is present. WARRANTY INFORMATION Warranty claims for replacing a Dual Mass Flywheel are subject to denial or debit when it is determined that the diagnostic procedures outlined above were not followed. ATTACHMENTS View PDF attachment M210114_Dual-Mass_Flywheel_Inspection.
M1301142018-11-13. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. "N14 and N18 Engine: High-pressure Pump Repair Instruction. INFORMATION The current version of ISTA/D Repair Instruction 13 51 017, ""Removing and installing or replacing high-pressure pump (N14, N18)"" has a procedure error. The current version of the Repair Instruction states to replace the high-pressure supply hose on the N14 engine. The Repair Instruction also states not to replace the high-pressure supply hose on the N18 engine. The N18 portion of the Repair Instruction is incorrect. As an interim solution, follow the procedure outlined below until this portion of the Repair Instruction is corrected. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/159...2/5/2014 Page 2 of 2 Bosch High-pressure Pump (1): All vehicles equipped with the N18 engine and produced from 3/2012 and later When the engine is fitted with a Bosch High-pressure Pump (1), the highpressure supply hose (2) MUST NOT be replaced when making repairs. The remaining portion of the Repair Instruction and tightening torques is correct. Refer to EPC for the applicable part numbers when making repairs."
M1201142018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE. N16: Fault 274D Mixture Adaptation Is Stored in the DME. Certain low speed, light-load driving conditions at lower outside temperatures could cause the Service Engine Soon lamp (MIL) to illuminate. The following fault would be stored in the DME: ??Fault 274D: Mixture adaptation, lower engine speed range (mixture too lean) CAUSE 1. Possible intake/exhaust leaks, or a faulty component as listed in the test plan 2. Unfavorable DME software.
M1104132018-11-13. Service bulletin. ENGINE. Service Action: N14 Engine Check Timing Chain Tensioner and Timing Chain. The timing chain tensioner applies pre-tension to the timing chain guide rail mechanism. In some cases, the tensioner spring force may be too low. Depending on the severity of the wear, it may lead to a rattling noise when starting the engine cold or when the engine is idling. CAUSE The timing chain tensioner internal tolerances are not consistent.
M1101122018-11-13. Service bulletin. ENGINE; ELECTRICAL SYSTEM. "N16 and N18 Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid. DIAGNOSTIC Below is the procedure for identifying how far the engine oil has migrated inside the engine electrical harness, when this issue occurs, if at all. The procedure must be followed very carefully so that the proper repair is identified. 1. Disconnect the oil pump volume control solenoid valve electrical connection per Repair Instructions 11 41 519 ""Removing and installing or replacing the solenoid valve (engine oil pump)."" Inspect the electrical connector; if no engine oil is found inside the electrical connector, perform the oil pump volume control valve repair procedure. If engine oil is found inside the electrical connector, proceed to diagnostic procedure step 2. 2. Remove the cover from the DME and remove all three electrical connectors from the DME. Inspect the connectors for traces of engine oil. If no engine oil is found, perform the oil pump volume control valve repair procedure and replace the engine section of the wire harness. Refer to EPC for the additional part number. If engine oil is found in the DME connector, proceed to step 3. 3. If engine oil is found in the DME electrical connector, perform the oil pump volume control valve repair procedure, replace the engine section of the wire harness and replace the DME. Refer to EPC for the additional part numbers. Do not remove the engine oil pan. Do not replace the oil pump volume control valve. Do not replace engine oil pump. OIL PUMP VOLUME CONTROL VALVE REPAIR"
M6402152018-11-13. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR; ENGINE AND ENGINE COOLING. The Blower Motor is Faulty. The blower motor does not operate at any fan speed. The blower motor may work intermittently with the blower fan speed operating only on FULL speed. CAUSE The blower motor is faulty and causes the blower resistor to fail.
M1701152018-11-13. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE. "Engine Cranks, No Start and/or Engine Coolant Temperature Faults. 1 The engine either exhibits a crank, no start or a hard start (long crank), usually on a cold engine. No faults are stored in the DME. Proceed to Correction 1 for further diagnosis. 2 NOTE: The engine may also exhibit the same starting behavior as in Situation1. The Service Engine Soon lamp is illuminated, with one or more of the following fault codes stored in the DME: Engine temperature sensor faults ? 2943 Coolant temperature sensor, signal change too fast ? 2937 Coolant temperature sensor, electrical: short circuit to positive ? 2936 Coolant temperature sensor, electrical: short circuit to earth ? 293A Coolant temperature sensor, plausibility, cold start: temperature too high ? 293B Coolant-temperature sensor, plausibility, cold start: Temperature too low ? 2947 Coolant-temperature sensor, signal: Fixed on low ? 2948 Coolant-temperature sensor, signal: Fixed ? 3393 Engine downtime, plausibility: Time too long in correlation with engine coolant cooling down ? 3392 Engine downtime, plausibility: Time too short in correlation with engine coolant cooling downIf any of the above fault codes are stored, proceed to Correction 2. Engine thermostat faults: ? 348E Characteristic map thermostat, actuation: Short circuit to positive ? 348F Characteristic map thermostat, actuation: Short circuit to earth ? 3490 Characteristic map thermostat, actuation: Open circuit If any of the above fault codes are stored then proceed to Correction 2: The above fault codes for the engine temperature sensor and thermostat are the primary fault codes for turning the Service Engine Soon light on. 1. Poor solder contacts in the engine coolant temperature sensor integrated into the engine thermostat housing 2. A faulty external or replaceable engine coolant temperature sensor (see below for identifying production changes in the thermostat and engine temperature sensors) 3. A faulty map-contro
M0107162018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. "N14 ENGINE TIMING CHAIN AND TENSIONER: LIMITED WARRANTY EXTENSION TO 7 YEARS/100,000 MILES. INFORMATION As part of a Class Action Suit Settlement for the vehicles listed above (""Class Vehicles""), MINI USA, a division of BMW of North America, LLC, is extending the limited warranty for the engine timing chain and tensioner to: 7 years/100,000 miles as determined by the vehicle's original in-service date This component-specific limited warranty extension applies to: Defects in materials or workmanship; and this Extended coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the MINI New Passenger Car Limited Warranty. For the eligible MINI vehicles, the limited warranty extension applies to the: Timing Chain (1) Timing Chain Tensioner with Seal Ring (4) In conjunction and when necessary, the parts listed below may only be claimed when there replacement is required to ""properly"" perform a covered repair of the timing chain and/or tensioner: Guide Rail (2) Tensioner Rail (3) Timing Chain Tensioner Seal Ring (5) Crankshaft Sprocket (6) Guide Rail (11) Bearing Bolt with Washer (13) Washer (14) Bearing Bolt with O-ring (15) O-ring (16)Note: This bulletin is a notice of a component-specific ""limited warranty extension as part of a Class Action Settlement. This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the MINI vehicle is currently experiencing a problem with the timing chair and/or tensioner."
M1101122018-11-05. Service bulletin. ENGINE. SI M11 01 12February 2015 EngineTechnical Service This Service Information bulletin supersedes SI M11 01 12 dated March 2014. designates changes to this revision SUBJECT N16 and N18 Engine: Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid. DIAGNOSTIC
M0112162018-11-05. Service bulletin. ENGINE AND ENGINE COOLING. "ENGINE MECHANICAL WATER (COOLANT) PUMP: LIMITED WARRANTY EXTENSION TO 7 YEARS/84,000 MILES. INFORMATION As part of a Class Action Suit Settlement for the vehicles listed above (""Class Vehicles""), MINI USA, a division of BMW of North America, LLC, is extending the limited warranty for the engine mechanical water pump to: z Item #1: This ""component-specific"" limited warranty extension applies to defects in materials or workmanship. z This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the MINI New Passenger Car Limited Warranty. z When it is necessary, the friction wheel is covered only when it is done in conjunction with performing an eligible and covered engine mechanical water pump repair. z This extended coverage does not apply to electric water pump. Note: This bulletin is a notice of a component-specific ""limited warranty extension as part of a Class Action Settlement. This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the MINI vehicle is currently experiencing a problem with the water pump."
BMWDEC01162018-11-05. Service bulletin. ENGINE AND ENGINE COOLING. "Update MINI Water Pump Class Action Settlement: Herremans v. BMW of North America, LLC. MINI USA, a division of BMW of North America, LLC (""MINI USA"") has entered into a nationwide settlement with the plaintiffs in the above referenced class action and the Court has granted final approval of the settlement. This DCS message provides you with the latest information about this case and the settlement. Class Allegations. The Plaintiff claimed that MINI produced and sold certain MINI Cooper Class Vehicles with defective water pumps. Class Vehicles are MINI R55, R56, R57, R58, R59, and R60 Series vehicles equipped with N12, N14, N16 or N18 engines that were sold or leased to Class Members in the US (including Puerto Rico). The Class Vehicles were produced from October 2006 through November 2012."
M1701152018-10-09. Service bulletin. ENGINE AND ENGINE COOLING. ENGINE CRANKS, NO START AND/OR ENGINE COOLANT TEMPERATURE FAULTS: NOTE: The engine may also exhibit the same starting behavior as in Situation1.
12 09 152016-02-04. Service bulletin. ENGINE; ELECTRICAL SYSTEM. MINI: FAULTY SOFTWARE FOR THE TANK VENTILATION CONTROL DISPLAYS ENGINE THROTTLE REACTION WHEN TEMPERATURE IS HIGH OUTSIDE, AND MORE OBVIOUS IF THE TANK IS ONLY PARTLY FILLED. *MA
12 07 152016-02-04. Service bulletin. ENGINE; ELECTRICAL SYSTEM. MINI: FAULTY SOFTWARE CAUSES THE CHECK CONTROL AND ENGINE POWER REDUCED LIGHT TO APPEAR. *MA
12 06 152016-02-04. Service bulletin. ELECTRICAL SYSTEM; ENGINE. MINI: BECAUSE OF THE DME SOFTWARE, AND A DAMAGED CLUTCH, THE DRIVETRAIN MALFUNCTION CHECK MESSAGE APPEAR. *MA
12 05 152016-02-04. Service bulletin. ELECTRICAL SYSTEM; ENGINE. MINI: DUE TO FAULTY DME SOFTWARE, THE SERVICE ENGINE LIGHTS COMES ON, INCLUDING THE CHECK CONTROL MESSAGE FOR MOTOR FORCE DECREASE. *MA
11 06 152016-02-04. Service bulletin. ENGINE; ELECTRICAL SYSTEM. MINI: DIFFERENT FAULTS ACTIVATES ENGINE MALFUNCTION AND OIL WARNING. *MA
11 02 152016-02-03. Service bulletin. ENGINE. MINI: A MECHANICAL FAILURE AND DME SOFTWARE ERROR OF THE VANOS ACTUATORS CAUSE THE ENGINE TO RUN ROUGH WHICH ACTIVATES THE MALFUNCTION WARNING LIGHT. *MA
SIM-11-10-142015-06-10. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER; ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER. MINI: SOME VEHICLES HAVE TURBOCHARGER NOISE AND A LACK OR LOSS OF PERFORMANCE, DUE TO RESTRICTION OF TURBOCHARGER OIL SUPPLY, RESULTING IN OIL STARVATION AND SEIZING OF TURBOCHARGER ASSEMBLY. MODEL ALL. *PE
SIM-12-07-122012-07-26. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE. MINI: THERE IS A SOFTWARE ERROR CAUSING THE SERVICE ENGINE SOON LIGHT TO BE ILLUMINATED THAT IS RELATED TO VALVETRONIC DIAGNOSTICS. MODELS R55, R56, R58, R57, R60, R59. NO MODEL YEARS LISTED. *PE
SIM-11-03-122012-07-26. Service bulletin. ENGINE. MINI: WHEN RESEALING ENGINE OIL PAN, ENGINE OIL PAN GASKET REPLACEMENT SHOULD NO LONGER BE USED DUE TO CAUSING SEALING FLANGE BECOMING DEFORMED. MODELS R55, R56, R59, R60, R57, AND R58. NO MODEL YEARS LISTED. *PE
SIM-11-01-122012-07-25. Service bulletin. ENGINE. MINI: ON CERTAIN MODEL VEHICLES, AN ENGINE OIL LEAK MAY OCCUR, DUE TO THE COMPROMISED OIL PUMP VOLUME CONTROL SOLENOID VALVE, FROM THE UNDERSIDE OF ENGINE. NO MODEL YEARS LISTED. *PE UPDATED 4/19/2013. *KB UPDATED 3/11/14. *PE
SI-M51-02-122012-04-24. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE. MINI: INSTALLATION OF A HEAT SHIELD FOR THE BONNET INTAKE AIR GRILL. *KB
SIM-17-01-102011-09-12. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM. BMW: ENGINE TOO HOT MESSAGE IS DISPLAYED WITH STORED TROUBLE CODES. THE WATER PUMP DOESNT POWER UP. *RM
SIM-11-07-082011-05-18. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV). BMW: DESCRIPTION AND SPECIFICATIONS OF CRANKCASE VENTILATION SYSTEM. *RM

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.