WenmarOpen by Wenmar Pro

Service bulletins for the 2007 MINI Cooper

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

138 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
SIM0105112022-08-01. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE. N12 Tank leak diagnostic module (DMTL) pump:limited warranty extension to 10 years/120,000 miles
BMWJUL13162021-05-17. Service bulletin. ENGINE; EQUIPMENT. MINI Water Pump Class Action Settlement
M0104192020-02-18. Service bulletin. ELECTRICAL SYSTEM; ENGINE; FUEL SYSTEM, GASOLINE. CLASS ACTION SETTLEMENT: N14 HIGH-PRESSURE FUEL PUMP (HDP) SERVICE BENEFIT CLASS VEHICLES: The MINI vehicle may experience a sudden engine operational failure reduced or loss of power while driving and the malfunction indicator lamp (MIL) may be illuminated along with high-pressure fuel pumprelated faults stored in the Engine Control Module (DME). PROCEDURE Perform the corresponding diagnosis/vehicle test and run the test plans to completion as applicable.
M2401122019-07-12. Service bulletin. ENGINE; ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Programming a Replacement EGS Module with ISTA/P. Programming a replacement electronic transmission control module (EGS) with ISTA/P requires the manual entry of the correct target basic and programmed part numbers. Programming concept.
M1202102019-07-12. Service bulletin. EQUIPMENT:MECHANICAL; ENGINE. "Cooper S with N14: Diagnosis for Misfire Faults. The Service Engine Soon (MIL) lamp is illuminated and/or the customer complains that the engine runs rough (engine cold or warm) with any of the following misfire faults stored in the DME: * 2771, 2772, 2773, 2775, 2776, 2777, 2779, 277A, 277B, 277D, 277E, 277F - "Combustion misfire, cylinder 1..4", sometimes together with: * 2781, 2782, 2783 - "Combustion misfire, multiple cylinders." On rare occasions, the Service Engine Soon lamp may not be illuminated (with misfire faults still stored in the DME) when the vehicle is brought to the workshop. Multiple causes related to electrical and mechanical engine components, or poor fuel quality in combination with unfavorable driving behavior (low loads and short driving distances). This condition may lead to possible clogging of the injector tips, causing a disturbance of the fuel spraying pattern or excessive carbon deposits on the intake valves/ports, resulting in reduced air flow into the combustion chambers."
M1202102018-12-17. Service bulletin. ENGINE AND ENGINE COOLING. "The Service Engine Soon (MIL) lamp is illuminated and/or the customer complains that the engine runs rough (engine cold or warm) with any of the following misfire faults stored in the DME: * 2771, 2772, 2773, 2775, 2776, 2777, 2779, 277A, 277B, 277D, 277E, 277F - ""Combustion misfire, cylinder 1..4"", sometimes together with: * 2781, 2782, 2783 - ""Combustion misfire, multiple cylinders"" On rare occasions, the Service Engine Soon lamp may not be illuminated (with misfire faults still stored in the DME) when the vehicle is brought to the workshop. Multiple causes related to electrical and mechanical engine components, or poor fuel quality in combination with unfavorable driving behavior (low loads and short driving distances). This condition may lead to possible clogging of the injector tips, causing a disturbance of the fuel spraying pattern or excessive carbon deposits on the intake valves/ports, resulting in reduced air flow into the combustion chambers."
M1706122018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. "Service Action: Retrofit of the Engine Coolant Temperature Sensor. Internal corrosion could form in the engine coolant temperature sensor. This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting and/or a ""Service Engine Soon"" lamp being illuminated."
M1202102018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. "Cooper S with N14: Diagnosis for Misfire Faults. The Service Engine Soon (MIL) lamp is illuminated and/or the customer complains that the engine runs rough (engine cold or warm) with any of the following misfire faults stored in the DME: ??2771, 2772, 2773, 2775, 2776, 2777, 2779, 277A, 277B, 277D, 277E, 277F - ""Combustion misfire, cylinder 1..4"", sometimes together with: ??2781, 2782, 2783 - ""Combustion misfire, multiple cylinders"" On rare occasions, the Service Engine Soon lamp may not be illuminated (with misfire faults still stored in the DME) when the vehicle is brought to the workshop. Multiple causes related to electrical and mechanical engine components, or poor fuel quality in combination with unfavorable driving behavior (low loads and short driving distances). This condition may lead to possible clogging of the injector tips, causing a disturbance of the fuel spraying pattern or excessive carbon deposits on the intake valves/ports, resulting in reduced air flow into the combustion chambers."
M1707122018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. "Service Action: Retrofit of the Engine Coolant Temperature Sensor. Internal corrosion could form in the engine coolant temperature sensor. This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting and/or a ""Service Engine Soon"" lamp being illuminated."
M1706122018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. "Service Action: Retrofit of the Engine Coolant Temperature Sensor. Internal corrosion could form in the engine coolant temperature sensor. This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting and/or a ""Service Engine Soon"" lamp being illuminated."
M1106122018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. During Engine Oil Service a Small O-Ring Is Found in the Oil Filter Housing. No customer complaint has been received. During the scheduled engine oil service, the technician notices a black rubber o-ring lying on the bottom of the engine oil filter housing. The o-ring has been dislodged from the non-return valve inside the engine oil filter housing. No subsequent engine damage occurs from the dislodged o-ring. Engine oil filter housing (1) Rubber o-ring (2) The material dimensions of the rubber o-ring are not satisfactory, allowing it to become dislodged from its installation location.
M1202132018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. State Inspection and Emission (I/M) Test Fails to Read 17-Character VIN. An affected vehicle may fail to pass a state-mandated Inspection and/or Emission (I/M) test due to a noncompliant 17-character vehicle identification number (VIN) being read out and displayed on the state's required tester report printout. In accordance with the OBD regulation, all MY 2005 and newer vehicles are required to support the display of their compliant 17-character VINs. These vehicles were produced to be in compliance with this regulation. If the DME was reprogrammed using the previously available BMW service equipment (e.g., Progman, GT1), it was possible that only the last 7 of the VIN were entered into the DME, and positions 4 through 10 may only contain default characters. For example: The state I/M tester or OBD scan tool may read out WBAAA00000A123456 instead of the correct full 17-digit VIN, WBAZZ03492A123456.
M1105132018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. Service Action: N14 Engine Retrofit Turbocharger Engine Oil Supply Line Heat Shield. After switching off the engine, the heat radiating from the turbocharger may cause the engine oil to solidify in the oil supply line to the turbocharger. This can lead to a restriction in the oil supply line, resulting in damage to the turbocharger bearings. CAUSE Close proximity of the turbocharger engine oil supply line and the turbocharger
M1202132018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. State Inspection and Emission (I/M) Test Fails Due to an Invalid VIN Number. The affected vehicle may fail to pass a State Inspection and Emission (I/M) test due to a noncompliant 17-digit vehicle identification number (VIN) stored in the DME (Digital Motor Electronic). The VIN read-out displayed on the state test printout does not match the actual VIN of the vehicle. If the DME was reprogrammed using the previously available BMW service equipment (e.g., Progman, GT1), it was possible that only the last 7 of the VIN were entered into the DME, and positions 4 through 10 may only contain default characters. For example: The state I/M tester or OBD scan tool may read out WBAAA00000A123456 instead of the correct full 17-digit VIN, WBAZZ03492A123456.
M1201132018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. N16 Engine: FC 2D9B Knock Sensor, Signal Is Stored in the DME. Certain areas of the US experience extremely cold climate conditions during the winter months, which can cause the Service Engine Soon lamp to illuminate while the engine temperature is increasing to full operating temperature. The following fault may be stored in the DME: ??FC 2D9B Knock Sensor, Signal CAUSE Unfavorable DME knock sensor diagnostic at outside ambient temperatures below -5° C
M1104132018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. Service Action: N14 Engine Check Timing Chain Tensioner and Timing Chain. The timing chain tensioner applies pre-tension to the timing chain guide rail mechanism. In some cases, the tensioner spring force may be too low. Depending on the severity of the wear, it may lead to a rattling noise when starting the engine cold or when the engine is idling. CAUSE The timing chain tensioner internal tolerances are not consistent.
M1103092018-11-26. Service bulletin. ENGINE. Whistling Noise from the Water Pump Area. A whistling or squealing noise is heard from the engine at idle and/or at higher engine speeds. CAUSE 1. Noise is caused by the water pump. 2. Noise is caused by the friction wheel of the belt tensioner.
M1101132018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. Service Action: Replace the Coolant Pump. Coolant is leaking from the coolant pump. CAUSE The coolant pump may develop cracks in the plastic housing. These cracks may result in a coolant leak.
M1101122018-11-26. Service bulletin. ENGINE. Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.
M1201132018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. "N16 Engine: FC 2D9B Knock Sensor, Signal Is Stored in the DME. Certain areas of the US experience extremely cold climate conditions during the winter months, which can cause the Service Engine Soon lamp to illuminate while the engine temperature is increasing to full operating temperature. The following fault may be stored in the DME: FC 2D9B Knock Sensor, Signal While performing test plan B1214 M KNOCK SENSOR, the following error message will be displayed: ""An error has occurred during execution of a service program. Fault code: 61/3."" This error in the test plan will not allow diagnosis to continue. The test plan error will be repaired with ISTA/D 2.36.0. CAUSE A DME calibration error in the knock sensor diagnostics results in an increased sensitivity threshold to cold temperatures."
M1707122018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. Service Action: Retrofit of the Engine Coolant Temperature Sensor. Internal corrosion could form in the engine coolant temperature sensor. This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting and/or a "Service Engine Soon" lamp being illuminated.
M1104142018-11-13. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; ENGINE. N16 Engine: Oil Leak from Cylinder Head Sealing Plug. An oil leak can develop at a sealing plug located in the cylinder head, just below the vacuum pump. The sealing plug was not tightened sufficiently during production.
M1104142018-11-13. Service bulletin. ENGINE. N16 Engine: Oil Leak from Cylinder Head Sealing Plug. An oil leak can develop at a sealing plug located in the cylinder head, just below the vacuum pump. CAUSE The sealing plug was not tightened sufficiently during production.
M1201142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. N16: Fault 274D Mixture Adaptation Is Stored in the DME. Certain low speed, light-load driving conditions at lower outside temperatures could cause the Service Engine Soon lamp (MIL) to illuminate. The following fault would be stored in the DME: Fault 274D: Mixture adaptation, lower engine speed range (mixture too lean) CAUSE 1. Possible intake/exhaust leaks, or a faulty component as listed in the test plan 2. Unfavorable DME software
M1101122018-11-13. Service bulletin. EQUIPMENT; ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. N16 and N18 Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.