Service bulletins for the 2024 Mercedes-Benz CLE
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
157 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| ANN Interm. Issues Flash | 2026-07-02. Other. ELECTRICAL SYSTEM. We are experiencing intermittent issues when flashing A26/17 - MBUX multimedia system + Instrument cluster (Head unit) when using flashing method ethernet to USB-C. Until further notice, please flash via VCI only. |
|---|---|
| LI00.20-P-078424 | 2026-06-17. Service bulletin. ELECTRICAL SYSTEM. Complaint The remaining time shown on the instrument cluster in the workshop menu (days to next due service) is implausible (>365 days) for the following conditions: • for the date of the vehicle handover • or the last conducted and confirmed Service A/B Cause Case 1: Observe the following on vehicles with a disconnected on-board electrical system battery (12V/48V): • The period in which the on-board electrical system battery is disconnected cannot be counted by the maintenance computer. • As soon as the on-board electrical system battery is connected again, the maintenance computer automatically starts counting without making a correction to the remaining time (days until the next service). Case 2: If a disconnected on-board electrical system battery (12V/48V) can be ruled out as the cause, it is possible that: The daily turnover counter inside the electronic ignition lock (EIS) has experienced memory loss. This anomaly was detected in the EIS software from modification year 2022 onward. To do this, please check the plausibility of the daily turnover counter as follows: If "TUSZ Assyst Plus" < the actual days since "Handover Date/DAY/Month/Year," then proceed to remedy for case 2. Information: A variation of 2-3 days is still considered plausible. If "TUSZ Assyst Plus" is plausible, or if a remaining time of 365 days is permanently displayed, check whether the vehicle has been handed over. These types of cases have different causes. (The respective values are included in the maintenance data in the control unit log of the instrument cluster). Remedy For case 1: When the on-board electrical system battery is disconnected, this period must always be taken into account for these vehicles, and the following condition must be met for a correct calculation to be made: • (A): The number of days from the "date of vehicle handover or last service A/B" to the "date on which the vehicle arrived at the workshop." • (B): Remaining time (days until the next service, as shown in the instrument cluster). • (C): Days on which the on-board electrical system battery was disconnected. The formula requires the following condition to be complied with. 365 - (A) [days] = (B) - (C) [days] For case 2: If the on-board electrical system battery (12 V/48 V) was not disconnected and the remaining time shown in the customer or workshop menu on the instrument cluster (days until the next service) is implausible in terms of the date of the vehicle handover or the last performed and confirmed service A/B, or the condition in the formula was not met, the service can still be performed and confirmed. For vehicles arriving more than 90 days after the service due date, the DSB service history can only be corrected by re-entering "Vehicle regularly serviced." A software fix for the EIS (electronic ignition lock) is currently in planning. The objective is to have a remedy available for 2026. Until the remedy is available, it is advisable to inform the customer that the next service is due again after 365 days at the latest. |
| LI00.20-P-077615 | 2026-06-16. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. "Perform vehicle handover" in the workshop menu to start the maintenance computer for service A/B cannot be carried out. 2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)). Vehicle handover was not performed. Remedy For model series 290 AMG up to and including AEJ 22 and model series 167 up to and including AEJ 21/2, the following applies: Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in N127 powertrain control unit. For model series 167 as of AEJ 22/1, 192 AMG, 206, 214, 232 AMG, 236, 254, 290 AMG as of AEJ 23, 294, 295, 296, 297 and 465, the following applies: Reinitialize ASSYST Plus under Adaptations – Teach-in processes – ASSYST PLUS in control unit N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)), and then perform the special procedure for reinitializing the ASSYST data in powertrain control unit N127. |
| LI00.20-P-077615 | 2026-06-02. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. "Perform vehicle handover" in the workshop menu to start the maintenance computer for service A/B cannot be carried out. 2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)). Vehicle handover was not performed. Remedy For model series 290 AMG up to and including AEJ 22 and model series 167 up to and including AEJ 21/2, the following applies: Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in N127 powertrain control unit. For model series 167 as of AEJ 22/1, 192 AMG, 206, 214, 232 AMG, 236, 254, 290 AMG as of AEJ 23, 294, 295, 296, 297 and 465, the following applies: Reinitialize ASSYST Plus under Adaptations – Teach-in processes – ASSYST PLUS in control unit N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)), and then perform the special procedure for reinitializing the ASSYST data in powertrain control unit N127. |
| LI46.15-P-070510 | 2026-05-30. Service bulletin. STEERING. Complaint Noises from the area of the steering column. - Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. • Instrument panel support • Steering column switch module NOTE: Occasionally to verify complaint, the steering column/vehicle needs to be in direct sunlight or hot conditions for a few hours. If noise only occurs when adjusting the steering column via electric actuation, please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on all pivot points including, but not limited to, green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, wipe excess grease off and perform greasing and movement to limit stops in all directions again. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. Include detailed items of the following: • Position of height and longitudinal adjustment when the noise occurs • If possible, locate affected component part on steering column • State any change in the noise when steering column component parts are touched (e.g. spring, etc.) |
| LI54.10-P-080602 | 2026-05-21. Service bulletin. ELECTRICAL SYSTEM. Complaint 48V battery (A66) part numbers A 000 982 78 24, A 000 982 57 30, A 000 982 88 31, A 000 982 50 32, A 000 982 87 32) may trigger a fault message ("48 V Service Required" with fault codes P0ADA91, P0ADE91, P0AA100, P0ADD00 or P0AA000) in the instrument cluster. This fault message may prevent the 48 V battery contactors from opening automatically if the 12 V power supply is interrupted. In this case, the 48 V on-board electrical system, including connected components, remain energized. Cause The contactors of the 48 V battery do not open, resulting in residual voltage (> 3V) even when the 12 V battery is disconnected. Remedy When working on the 48 V on-board electrical system or connected components, ensure the component being repaired is de-energized in the 48 V system after disconnecting the 12 V ground line. Use a DVOM and ensure that there is less than 3V across the 48V terminals. • If the voltage is less than 3V, the repair can be continued in accordance with the WIS documentation. • If the voltage is greater than 3V, disconnect the ground line from the 48 V on-board electrical system battery and secure from contacting any ground points of the vehicle before continuing the repair. Once the work has been completed, follow the procedure for clearing the 48 V battery fault message as specified. |
| LI82.30-P-059239 | 2026-05-20. Service bulletin. VISIBILITY/WIPER. Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock). |
| LI91.29-P-080554 | 2026-05-15. Service bulletin. SEATS. Complaint One or more seat functions are restricted or inoperative. This may include: • Seat memory • Automatic seat adjustment • Easy Entry/Exit • Head restraint presetting • Collision avoidance with bench seat at rear • Actuation by other vehicle systems Seat normalization is missing, and fault code B228678 – “The control unit calibration has been lost or was not performed. Adaptation or adjustment is not correct.” is stored in the seat control unit. Additional fault codes may also be present. Cause The condition is currently under investigation. Remedy Process any additional faults first. • If a clear cause is found (for example, a failed component, wiring issue, or connector concern), repair that issue as required. If no root cause can be determined: • Do NOT perform Initial Start-up, Software Update, or Normalization of the Control Unit • Create a control unit log for the affected seat control unit. • Open a TIPS case to the Body/Chassis/Entertainment inboxand attach the control unit log for further analysis. |
| LI54.65-P-080132 | 2026-05-14. Service bulletin. BACK OVER PREVENTION: WARNINGS; ELECTRICAL SYSTEM; LANE DEPARTURE: BLIND SPOT DETECTION. Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide. |
| LI46.15-P-070510 | 2026-05-11. Service bulletin. STEERING. Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. • Instrument panel support • Steering column switch module If noise only occurs when adjusting the steering column via electric actuation please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, perform above procedure again and anywhere there are movement or friction points that the noise seems to be emanating from. 8. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 9. If noise still does not resolve, please open a TIPS case. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. A detailed description includes: • Position of height and longitudinal adjustment when the noise occurs • If possible, locate affected component part on steering column • State any change in the noise when steering column component parts are touched (e.g. spring, etc.) |
| PSL-NCU Return Parts 5/08 | 2026-05-11. Other. AIR BAGS; VISIBILITY/WIPER. Dear Mercedes-Benz USA Dealers, The part numbers listed in the chart below should no longer be installed, and any existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, May 28, 2026. After May 28th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below. |
| LI91.10-P-076097 | 2026-05-04. Service bulletin. SEATS. Complaint Play/noise at height adjuster or in seat guide rail on front seats Cause Tolerances and variations in the manufacturing process Remedy 1. Inspect Seat Height Adjuster Barcode Label (See Pic.1) • Locate the barcode label on the cross tube of the seat height adjuster. • In isolated cases, the barcode label may be located on the front side of the cross tube. If not visible, remove the seat cushion to access the label. 2. Evaluate Production Status If Production Status is LOWER than E108 → Replace the seat frame base with the height adjuster motor. If Production Status is E108 or HIGHER → Do NOT replace parts. Please submit a TIPS case to the Body/Chassis/Entertainment inbox and attach: • Video of the noise concern • Photo of the barcode label To improve analysis quality, ensure the video meets the following criteria: • Seat installed in the vehicle • Quiet workshop environment • Steady and smooth camera movement • Good lighting on the suspected noise area • Recording with two people (one filming, while the other is creating the noise-causing movement) • Noise‑causing movement must be clearly visible • Camera position: From the rear footwell, looking forward at the front seat • Verbal explanation included in English or German |
| LI82.10-P-078301 | 2026-04-27. Service bulletin. EXTERIOR LIGHTING. Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304 |
| LI00.01-P-078887 | 2026-04-25. Service bulletin. UNKNOWN OR OTHER. Complaint The intent of this document is to provide workshops with helpful technical reference language. • Commonly used acronyms in LI's and TIPS cases. • Control unit names, numbers, and how to identify. • Network/wiring architecture groups to baumuster quick reference. • Platform to baumuster quick reference. Cause Information only Remedy Acronyms: • AV = Actual Values • CPR = Car Package Release (For MB.OS) • CU = Control Unit • CUL = Control Unit Log • DTC = Diagnostic Trouble Code • E-Stand = Fresh-up head unit boot software (found in head unit control unit log) • FUP = Fresh-up • FW = Firmware • HSVL = High Speed Video Line • HU = Head Unit • HW = Hardware • IPD = Injector Performance Data • ISU = Initial Start Up • LVDS = Low Voltage Differential Signal • NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) • NSFT = Not Safe For Transport • MOPF = Model Facelift (Ex: 167 MOPF) • PiH = Plug-in Hybrid • SA Code = Sonderausstattungscode (Option Code) • SCN = Software Calibration Number • SW = Software • TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) • QT = Quicktest • XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. • Control Unit Name • Control Unit Number • Control Unit Short name • Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 • 117, 156, 246 (MFA) • 166, 176, 221, 242, 246, 292 • 906 Star 2 • 205, 213, 238, 253, 257, 290 (MRA) • 117, 156, 246 (MFA) • 118, 177, 243, 247 (MFA2) • 167, 222, 292, 463, 465 • 907 Star 3 • 294, 295, 296, 297 (EVA2) • 206, 214, 223, 236, 254 (MRA2) • 192 and 232 (MSA) Star 3.5 • 174 • 178 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": • 205 • 213 • 222 • 238 • 253 • 257 • 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": • 206 • 214 • 223 • 236 • 254 MFA = "Mercedes-Benz Frontwheel Architecture" • 117 • 156 • 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" • 118 • 177 • 243 • 247 EVA1.5 = "Electric Vehicle Architecture" • 243 EVA2 = "Electric Vehicle Architecture - Generation 2" • 294 • 295 • 296 • 297 MSA = "Mercedes-Benz Sport Architecture" • 192 • 232 MMA = "Mercedes-Benz Modular Architecture" • 174 • 178 |
| NCU - 2026040005 | 2026-04-25. Service campaign. WHEELS; STRUCTURE:BODY. Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (“MY”) 2025 CLE (236 platform) vehicles, the seam seal in the front left wheel arch does not meet current production specifications which could result in leaks and subsequent corrosion in that area. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will rework the front left wheel arch seam seal on the affected vehicles. |
| LI54.71-P-079104 | 2026-04-20. Service bulletin. ELECTRICAL SYSTEM. Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. NOTE: • Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. • This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Do not replace parts. Please open a TIPS case to the Body/Chassis/Entertainment inbox but read the below carefully: • The vehicle must be exhibiting the concern as shown in the attachment videos. • The vehicle DOES NOT need to be at the dealer, nor does it need to be brought into the dealership. • If the geographic location is known, it is very important that it is provided. • Provide any pictures or videos, if available. A new software for the head unit is scheduled for tentative release in Q2 2026. |
| LI83.70-P-080411 | 2026-04-13. Service bulletin. VISIBILITY/WIPER. Complaint No heating output is available during electric driving operation. In conventional (combustion engine) driving operation, full heating output is available. Cause Possible defect in the N33/5 water heater (high-voltage PTC booster heater) Remedy If the N33/5 water heater (PTC booster heater, high voltage) is defective, it must be replaced with the latest part number. Note: Please refer to the information in XENTRY Parts Information and the latest WIS description. For vehicles manufactured before December 2025 with a BorgWarner water heater, the coolant hoses (inlet and outlet) must also be ordered and installed. For vehicles produced after December 2025, only the N33/5 water heater (PTC booster heater high voltage) needs to be replaced. Follow instructions in XPPI C74 note for the correct parts. |
| LI72.20-P-075746 | 2026-04-10. Service bulletin. STRUCTURE:BODY; ELECTRICAL SYSTEM. Complaint Tailgate opens unintentionally. Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") • an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the “Lock button", then double‑click the “Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer. |
| LI54.71-P-079104 | 2026-04-10. Service bulletin. ELECTRICAL SYSTEM. Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. NOTE: • Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. • This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy No TIPS case is necessary. Do not replace parts. A new software for the head unit is scheduled for tentative release in Q2 2026. |
| LI83.70-P-080411 | 2026-03-30. Service bulletin. VISIBILITY/WIPER; ELECTRICAL SYSTEM. Complaint No heating output is available during electric driving operation. In conventional (combustion engine) driving operation, full heating output is available. Cause Possible defect in the N33/5 water heater (high-voltage PTC booster heater) Remedy If the N33/5 water heater (PTC booster heater, high voltage) is defective, it must be replaced with the latest part number. Note: Please refer to the information in XENTRY Parts Information and the latest WIS description. For vehicles manufactured before December 2025 with a BorgWarner water heater, the coolant hoses (inlet and outlet) must also be ordered and installed. For vehicles produced after December 2025, only the N33/5 water heater (PTC booster heater high voltage) needs to be replaced. |
| LI00.01-P-078887 | 2026-03-28. Service bulletin. UNKNOWN OR OTHER. Complaint The intent of this document is to provide workshops with helpful technical reference language. • Commonly used acronyms in LI's and TIPS cases. • Control unit names, numbers, and how to identify. • Network/wiring architecture groups to baumuster quick reference. • Platform to baumuster quick reference. Cause Information only Remedy Acronyms: • AV = Actual Values • CU = Control Unit • CUL = Control Unit Log • DTC = Diagnostic Trouble Code • E-Stand = Fresh-up head unit boot software (found in head unit control unit log) • FUP = Fresh-up • FW = Firmware • HSVL = High Speed Video Line • HU = Head Unit • HW = Hardware • IPD = Injector Performance Data • ISU = Initial Start Up • LVDS = Low Voltage Differential Signal • NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) • NSFT = Not Safe For Transport • MOPF = Model Facelift (Ex: 167 MOPF) • PiH = Plug-in Hybrid • P3 Hybrid = AMG Plug-in Hybrid with rear drive unit • SA Code = Sonderausstattungscode (Option Code) • SCN = Software Calibration Number • SW = Software • TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) • QT = Quicktest • XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. • Control Unit Name • Control Unit Number • Control Unit Short name • Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 • 117, 156, 246 (MFA) • 166, 176, 221, 242, 246, 292 • 906 Star 2 • 205, 213, 238, 253, 257, 290 (MRA) • 117, 156, 246 (MFA) • 118, 177, 243, 247 (MFA2) • 167, 222, 292, 463, 465 • 907 Star 3 • 294, 295, 296, 297 (EVA2) • 206, 214, 223, 236, 254 (MRA2) • 192 and 232 (MSA) Star 3.5 • 174 • 178 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": • 205 • 213 • 222 • 238 • 253 • 257 • 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": • 206 • 214 • 223 • 236 • 254 MFA = "Mercedes-Benz Frontwheel Architecture" • 117 • 156 • 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" • 118 • 177 • 243 • 247 EVA1.5 = "Electric Vehicle Architecture" • 243 EVA2 = "Electric Vehicle Architecture - Generation 2" • 294 • 295 • 296 • 297 MSA = "Mercedes-Benz Sport Architecture" • 192 • 232 MMA = "Mercedes-Benz Modular Architecture" • 174 • 178 |
| LI46.10-P-079374 | 2026-03-28. Service bulletin. ELECTRICAL SYSTEM. Complaint Customer concern for ESP/Brake or Steering yellow instrument cluster message AND C220564 in the N80 Steering Column Control Module (Valeo Parts only). To check which supplier steering column module is present in the vehicle, see attachment "Supplier Identification". Cause Triggered due to communication related software timing. Remedy New software A2239026336. Update N80 (Steering Column Module) to at least target software A2239026336, clear codes, and ignition cycle the vehicle. If DTC is still present, re-flash N80 and clear DTC's. Is DTC still present? No --> Bus sleep the vehicle. After bus sleep check for DTC again. If DTC is not present, release vehicle. Yes --> Open a TIPS case to the Body/Chassis/Entertainment inbox. |
| LI82.85-P-077914 | 2026-03-19. Service bulletin. ELECTRICAL SYSTEM. Complaint Mercedes me connect services inoperative (me-Call, Remote Status, etc.). Mercedes me services - activation not possible Notes: - The event code "B129C00 - Malfunction in control unit for telematics services" is active and stored - The head unit shows no internet connection Cause Under analysis. Remedy Please create a TIPS case, attach a RAMSES control unit log to the case. |
| LI54.65-P-080132 | 2026-03-17. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide. |
| LI82.00-P-080029 | 2026-03-11. Service bulletin. ELECTRICAL SYSTEM; SEATS. Complaint The seat may no longer be adjustable using the electric seat adjustment switch on the door module. No related error is stored in the quick test. Cause Under certain conditions, the electric seat adjustment switch may remain in sleep mode. It is then not possible to adjust the seat using this switch. This is a software error. Remedy To restore functionality, perform the following steps: 1. Remove the door trim from the affected door. 2. Unplug and reconnect the plug of the electric seat adjustment switch (No. 2 in the picture in work instruction AR91.29-P-2522WT) to perform a reset of the switch. Note: The switch does not need to be removed for this. 3. To prevent this problem from recurring, the current software version A2239029930 should be installed on the switch module “Seat Adjustment Switch Group …”. Example: S22 - Select S22 – “Seat Adjustment Switch Group, front left” (SSE-VL) → Adaptations → Control unit update → Update control unit software. If the vehicle already has SW version A2239029930, there is another cause. Please open a TIPS case to the Body/Chassis/Entertainment inbox if the issue persists with the new software installed. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.