Service bulletins for the 2024 Mercedes-Benz CLE
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
157 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Brakes are shown. Show all
| LI42.10-P-078779 | 2026-10-06. Service bulletin. SERVICE BRAKES. Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team. |
|---|---|
| PSL-NCU Return Parts 7/3 | 2026-07-13. Other. SERVICE BRAKES; STRUCTURE:BODY; ELECTRICAL SYSTEM. Dear Mercedes-Benz USA Dealers, The part numbers listed in the chart below should no longer be installed, and any existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, July 23rd, 2026. After July 23rd, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below. |
| LI42.10-P-079904 | 2025-10-21. Service bulletin. SERVICE BRAKES. Complaint At low speeds and light brake pressure, brakes will make a groaning or honking noise. Cause Frictional vibrations with very light brake pressure/modulations. Remedy This condition can be duplicated on most vehicles. To validate, use a like for like reference vehicle. The noise is normal behavior under the conditions listed. With very light brake pressure this noise can be induced/caused due to normal brake pad and brake rotor vibrations. Exchanging brake components will not rectify. |
| LI42.10-P-063502 | 2025-02-22. Service bulletin. SERVICE BRAKES. Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and using approved cleaning agents). These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. 1. Beginning Diagnostics: a) Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it and then continue with1b. b) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). c) Check the affected system for component wear, mechanical damage or localized overheating damage. 1. Replace damaged components as necessary and re-assess noise concern. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). 2. Specific Axle Work: NOTE: If brake pad has a metal backing plate, there is no need to affix the adhesive film. a) If the noises are coming from the front axle => Affix linings with adhesive film (see attachments for front axle). If backing plate is installed on pads, move to step 3. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. For 6 piston calipers, only in the area of the center piston. For other piston caliper configurations less than 6, apply where the piston(s) makes contact with the back of the pad. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". 5. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle => Affix linings with adhesive film and grease the lining as per the specification (see attachments for rear axle). 1. Remove brake pads of rear axle. 2. Cleaning all contact points on brake lining and brake caliper/carrier. 3. Grease contact points (red areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste. 4. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 5. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. d) Finally drive approx. 3 miles to allow the system to cool. e) Reassess noise. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.