Service bulletins for the 2024 Mercedes-Benz CLE
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
157 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| LI82.10-P-078470 | 2024-10-25. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Complaint Message in instrument cluster "Adaptive high beams assistant not available/inoperative" or "DIGITAL LIGHT reduced range of functions" in relation to "FC151E29- The level sensor at front left has a malfunction. There is an invalid signal" in the HLI control unit. Cause Older software release, HLI control units Remedy Update of HLI control units (E1n9 / E2n9) |
|---|---|
| LI91.10-P-078471 | 2024-10-25. Service bulletin. SEATS. Complaint Damage to the leather strap of the seat backrest lock on the front seats (Pic.1). Cause Gap between seat backrest lock and trim ring Remedy • Ordering of new component parts (seat backrest lock and trim ring) • Clipping of trim ring to the seat backrest lock (holder) • Push the trim ring downwards • Apply the hot-melt dot from the inside - at the bottom between the trim ring and the holder of the seat backrest lock (the holder of the seat backrest lock and trim ring must be fixed together) (Pic.2) |
| LI82.35-P-078467 | 2024-10-25. Service bulletin. VISIBILITY/WIPER; STRUCTURE:BODY. Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage. |
| LI77.30-P-078299 | 2024-10-25. Service bulletin. STRUCTURE:BODY. Complaint For a problem involving the soft top opening/closing function in combination with the cited fault code, the retainer lock (4) on the closure of the soft top compartment cover may no longer be seated in its position. Cause The control cable may have become detached from its tray and pulled off the retainer lock as a result Remedy Cut through control cable (3) at knot (C) and remove from vehicle. Then install retainer lock (4) again in the position described in WIS. |
| LI54.71-P-078498 | 2024-10-22. Service bulletin. ELECTRICAL SYSTEM; WHEELS. Complaint "Active Emergency Stop Assist Currently Unavailable" and "Active Steering Assist Inoperative" instrument cluster messages along with Tire Pressure Light on in Instrument Cluster. Cause Both systems are temporarily unavailable due to low tire pressures. An active tire pressure monitor light may result in some assistance features being temporarily unavailable until tire pressures are corrected. Remedy Check/adjust tire pressures and reset monitoring through the instrument cluster. |
| LI82.70-P-077433 | 2024-09-28. Service bulletin. ELECTRICAL SYSTEM. Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: • It is recommended to replace the cover caps. • The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way. |
| LI82.70-P-078425 | 2024-09-27. Service bulletin. ELECTRICAL SYSTEM. Complaint White plastic insert present on microphone assembly. See figure A for example. Cause The insert (breathable filter) is designed to be inside for dust protection and air flow control. Remedy Do not remove the breathable filter from the microphone assembly. This part is designed to be in the microphone and should remain in the vehicle. Note: If TIPS support is required for microphone symptoms please open a TIPS case and reference this LI. |
| LI82.10-P-078307 | 2024-09-24. Service bulletin. EXTERIOR LIGHTING. Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. • If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: • LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system |
| LI82.90-P-078381 | 2024-09-24. Service bulletin. SUSPENSION; ELECTRICAL SYSTEM. Complaint Display dark (total or partial) of one or more ASCM (AMG) steering wheel button displays - see attachment. Note: There is no loss of vehicle functionality due to this complaint. Cause Software can cause a partial display on the ASCM. Remedy Please perform the following steps in the event of a total or partial display of the ASCM displays: 1. Perform a hard reset (disconnect power supply) of control unit A74/2 (ASCM) for 2 minutes. 2. Perform a software update of the A74/2 (ASCM), N145 (DRVU) and A26/17 (HU). 3. Reset the user profile via the head unit settings menu. (Full factory reset) |
| 2024090008 | 2024-09-23. Service campaign. VISIBILITY/WIPER. 1. Replace left door window lifter. For basic data, see AR67.39-P-0013WEC. 2. Assemble in reverse order. |
| LI91.10-P-078305 | 2024-09-17. Service bulletin. ELECTRICAL SYSTEM; SEATS. Complaint The "Easy entry and exit feature" function deactivates itself after a brief period. Cause The cause is currently being investigated. Remedy A remedy is currently not available. A software update in the seat control unit does not solve the problem. The document will be updated once the reason has been analyzed and a remedy is available. |
| LI82.10-P-078304 | 2024-09-14. Service bulletin. EXTERIOR LIGHTING. Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage. |
| LI82.10-P-078301 | 2024-09-13. Service bulletin. EXTERIOR LIGHTING. Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304 |
| LI77.30-P-078299 | 2024-09-11. Service bulletin. STRUCTURE:BODY. Complaint For a problem involving the soft top opening/closing function in combination with the cited fault code, the retainer lock (4) on the closure of the soft top compartment cover may no longer be seated in its position. Cause The control cable may have become detached from its tray and pulled off the retainer lock as a result Remedy Cut through control cable (3) at knot (C) and remove from vehicle. Then install retainer lock (4) again in the position described in WIS AR77.30-P-0999-04WEA. This WIS document also contains the relevant photographs with matching call outs. |
| LI98.00-P-078106 | 2024-09-11. Service bulletin. STRUCTURE:BODY. Complaint Damage or discoloration to paint protection films on vehicle. Cause Chip protection films are a wear item that may need to be replaced over the life of the vehicle. They are typically not covered by vehicle warranty. Remedy To properly install a paint/chip protection film, please follow the below guidelines: #1 - Utilize a solution that is 0.2% soap solution (1,000ml of water + 2ml of liquid soap). #2 - Clean the paint surface and ensure it is dust-free. #2a - When cleaning, you can utilize isopropyl alcohol (Rubbing Alcohol) to assist with cleaning. #2b - We recommend a lint-free rag for secondary dusting. #3 - Wet hands with the soapy water solution to protect the adhesive surface. #4 - Remove the backing paper from the film completely. #5 - Moisten the vehicle surface with the soapy water. You can also lay the protective film with adhesive side out onto the wetted surface to also cover the adhesive layer in the soapy water solution. #6 - Remove film and flip over to gently place adhesive side against the paint surface. #7 - Working from the center out, use a squeegee to press the soapy water solution out from under the film. Use sufficient pressure to firmly press the film into the paint surface, but not an excessive amount to damage or stretch the film. #8 - Allow film and paint to "cure" until all of the moisture has evaporated. At this time the adhesive should be dried and cured enough for sufficient hold to release the vehicle. |
| LI82.60-P-078155 | 2024-08-30. Service bulletin. ELECTRICAL SYSTEM. Complaint Radio reception interference and the following DTCs are displayed in the A26/17 - MBUX multimedia system control unit as "active and stored": • B19B313 - Antenna 1 open load • B19B413 - Antenna 2 open load • B19B513 - Antenna 3 open load • B19B613 - Antenna 4 open load Cause Antenna amplifier Remedy Replace the antenna amplifier. |
| NCU - 2024080003 | 2024-08-30. Service campaign. STRUCTURE:BODY. 1. Replace reinforcement sheet metal for radiator crossmember (8). For basic information, see AR62.30-P-2300WEB. |
| NCU - 2024070015 | 2024-08-29. Service campaign. STRUCTURE:BODY. 1. Rework paint damage using a touch-up paint pen and ensure anticorrosion protection. Observe MB specifications and manufacturer specifications. 2. Mask off transition from retaining tab to roof trim bar by means of an intermediate layer (3M protective film) prior to installation to prevent further damage when reinstalling the trim bar (B, Figure 2). 3. Assemble in reverse order. |
| CL - 2024020014 | 2024-07-30. Other. ELECTRICAL SYSTEM. The battery management control unit software does not meet current production specifications. The battery's state of health may not be calculated correctly, resulting in the false illumination of the check engine malfunction indicator lamp. An authorized Mercedes-Benz dealer will update the battery management control unit software, free of charge. Your vehicle must be brought to a dealer to complete the software update. |
| LI82.10-P-078069 | 2024-07-27. Service bulletin. EXTERIOR LIGHTING. Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4 °F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). |
| 2024020014 | 2024-07-25. Emissions. ELECTRICAL SYSTEM. Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (“MY”) 2023 -2024 GLC (254 platform), C-Class (206 platform), CLE (236 platform), E-Class (214 platform) and S-Class (223 platform) vehicles, the 48-volt battery module (BMS) control unit software does not correspond to the current series production configuration. It is therefore possible that the battery's state of health is calculated incorrectly, thereby falsely illuminating check engine light ‘MIL’ (malfunction indicator lamp). |
| LI82.60-P-077958 | 2024-07-04. Service bulletin. ELECTRICAL SYSTEM. Complaint USB port data storage medium is not recognized, but charging function is still available. We are only aware of this complaint in a few isolated cases and it only occurs intermittently (not in every driving cycle). Cause Multimedia connection unit Remedy Replace the multimedia connection unit. Affected item numbers: A 214 820 81 00 A 223 820 14 05 Manufactured before 10/2023 modified parts have been manufactured since 10/2023. |
| 2024060008 | 2024-06-30. Service campaign. STRUCTURE:BODY. Check/Test Procedure 1. Remove left rear inner lamp unit (E3/17, Figure 1) and right rear inner lamp unit (E4/17, Figure 1). For basic information, see AR82.10-P-4927WEC. 2. Remove the trim element (1, Figure 1) from the trunk lid (2, Figure 1). Installation: The trim element (1, Figure 1) is destroyed when you remove it and a new one has to be installed in its place. 3. Check the laser solder seam (area A, Figure 1) on the trunk lid (2, Figure 1) for cracks. Use a flashlight here to inspect for cracks. Work Procedure 1. Clean the affected area of the laser solder seam (area A, Figure 1) on the trunk lid (2, Figure 1) over a wide area. For example with silicone remover. 2. Apply activator to the affected area of the laser solder seam (area A, Figure 1) on the trunk lid (2, Figure 1). Observe manufacturer's specifications for product! 3. Seal the affected area of the laser solder seam (area A, Figure 1) on the trunk lid (2, Figure 1) with transparent seam seal. Seal approx. 2 cm over the entire crack length of the laser solder seam (area A, Figure 1). Observe manufacturer's specifications for product! 4. Install in the reverse order. |
| CL - 2024040001 | 2024-06-03. Other. WHEELS. An authorized Mercedes-Benz dealer will replace the TIREFIT bottle in the trunk of your vehicle, free of charge. The bottle may potentially leak and may not be available for use in case of a flat tire. Your vehicle must be brought to a dealer to complete this campaign. Please schedule an appointment by contacting our Customer Assistance Center at 1-800-367-6372, or locate your nearest dealer using the QR code and “Find a Dealer” section. |
| OTA - 24240501 | 2024-05-29. Over-the-air update. ELECTRICAL SYSTEM. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY23-24 CLE, E-Class, EQE, EQS, and S-Class vehicles (236, 214, 294, 295, 296, 297, 223 platform), the communication module SCN coding does not correspond with the latest series production configuration. The communication module will receive an OTA update that updates the SCN coding to the latest series production configuration. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.