WenmarOpen by Wenmar Pro

Service bulletins for the 2009 Mazda MX-5

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

212 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Equipment and accessories are shown. Show all

Bulletins, newest first
07-002-18-34322018-05-14. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/Cevaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. "Mazda Air Cooling Coil Coating" is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers. This treatment provides a durable coating that will aid to prevent biological reactions that lead to odorconcerns. It is applied to the evaporator in a misted form that is introduced by way of the cabin air filter, the re-circulate door, the blower motor resistor access, or the blower motor air intake. Proper application requires the evaporator surface to be: Relatively clean and free of leaves, dust build-up and debris. Thoroughly dried, and the product cured onto it after application. NOTE: Keep the cooling unit dry by leaving the blower fan ON (at least on low), even if the A/C is not being used. In low humidity (dry) conditions, keep the ventilation system in the "FRESH" mode all the time, or as much as possible. In high humidity conditions, or if the air has a lot of dust or pollen, keep the system in the "RECIRCULATION" mode. A few minutes before reaching a destination, turn the A/C OFF, but leave the blower fan ON. This stops the accumulation of condensation on the evaporator/cooling unit, and it helps dry the inside of the cooling unit. A/C odor is not unique to Mazda vehicles as it will occur in other makes and models. To minimize A/C odor, suggest the following to the customers.
05-001-18-34532018-05-14. Service bulletin. EQUIPMENT; POWER TRAIN. Always be sure to use the correct automatic transmission fluid when replacing ATF. Using the wrong ATF may cause shift quality complaints or may even damage the transmission. NOTE: ATF M-V (TYPE M5) IS NOT THE SAME FLUID AS MERCON®V OR MERCON®LV ATF. ATF M-V (TYPE M5) HAS A GREATER VISCOSITY THAN MERCON®V AND MERCON®LV ATF IN LOW TEMPERATURES. ATF M-V (TYPE M5) HAS A GREATER ANTI-JUDDER SPECIFICATION THAN MERCON®V AND MERCON®LV ATF. TRANSMISSION FLUID FLUSHING SHOULD ONLY BE PERFORMED WHEN INSTRUCTED BY THE WORKSHOP MANUAL OR ANY OTHER MAZDA PUBLICATION.
MT-004-182018-04-23. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.
MT-003-182018-04-23. Service bulletin. EQUIPMENT; AIR BAGS. The Workshop Manual has two-different airbag procedures, one for Standard Deployment and one for Two-Step Deployment. Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles.
09-019-18-34502018-04-23. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This service bulletin provides information regarding the proper use of the driver's floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another. Use these points at your dealership to protect our mutual operations and to help ensure our customers' safety.
00-001-18-34462018-04-23. Service bulletin. EQUIPMENT. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
09-035-17-30802017-10-04. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer?s responsibility to comply with Federal, State, and local laws concerning odometerand related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the ?SpeedometerReplacement Label?.Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda?s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service.With the use of SPECMO?s services, a Mazda dealer can get the odometer setting updated to reflect the correct mileage at the time of replacement for both warranty and customer pay repairs, therefore resulting in a higher level of customer satisfaction. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
09-013-16-31612017-06-09. Service bulletin. EQUIPMENT. WHEN DEALING WITH CUSTOMER COMPLAINTS OF EXCESSIVE CONDENSATION AND/OR WATER WITHIN THE HEADLAMP UNIT, FIRST DETERMINE IF ALL THE BULB SOCKETS ARE RESENT AND CORRECTLY INSTALLED. IN MOST CASES YOU WILL FIND THAT THE BULB SEAL NO. 1 (A) OR HID BULB SEAL NO. 1 (B) AND BULB SEAL NO. 2 (C) SOCKET OVERS HAVE NOT BEEN CORRECTLY INSTALLED OR ARE MISSING DUE TO IMPROPER PRIOR REPAIRS (I.E., CUSTOMER REPLACING THE HEADLAMP BULBS OR BODY SHOP NOT TRANSFERRING THEM WHEN REPLACING THE HEADLAMP UNIT(S) DUE TO A COLLISION). ANY DAMAGE CAUSED BY MISSING SOCKET COVERS, HID MODULE SEAL (D), OR MISSING BUMPER BRACKETS (E) IS NOT COVERED BY WARRANTY POLICY.
09-030-15-30732017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. MAZDA INFOTAINMENT SYSTEMS REQUIRE CONTACTING THE PROPER SOURCE FOR DIAGNOSTIC SUPPORT, PARTS AUTHORIZATION, AND PARTS EXCHANGE. SOME COMPONENTS REQUIRE PRIOR AUTHORIZATION BEFORE ORDERING AS EXCHANGE. REFER TO DAG EXCHANGE CENTRAL (MXCONNECT>PARTS AND ACCESSORIES>PARTS>PROGRAMS>EXCHANGE CENTRAL) FOR COMPONENT AVAILABILITY, SOURCE OF TECHNICAL SUPPORT AND PRIOR AUTHORIZATION REQUIREMENT. NOTE: ALWAYS CHECK FOR A TSB THAT MAY MODIFY OR ELIMINATE PRIOR AUTHORIZATION FOR A SPECIFIC SYMPTOM FOR A GIVEN COMPONENT.
05-001-16-31282017-05-26. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. ALWAYS BE SURE TO USE THE CORRECT AUTOMATIC TRANSMISSION FLUID WHEN REPLACING ATF. USING THE WRONG ATF MAY CAUSE SHIFT QUALITY COMPLAINTS OR MAY EVEN DAMAGE THE TRANSMISSION.NOTE:• ATF M-V (TYPE M5) IS NOT THE SAME FLUID AS MERCON®V OR MERCON®LV ATF.• ATF M-V (TYPE M5) HAS A GREATER VISCOSITY THAN MERCON®V AND MERCON®LV ATF IN LOW TEMPERATURES.• ATF M-V (TYPE M5) HAS A GREATER ANTI-JUDDER SPECIFICATION THAN MERCON®V AND MERCON®LV ATF.• TRANSMISSION FLUID FLUSHING SHOULD ONLY BE PERFORMED WHEN INSTRUCTED BY THE WORKSHOP MANUAL OR ANY OTHER MAZDA PUBLICATION. CAUTION:• USING ATF OTHER THAN ATF M-V (TYPE M5) IN AUTOMATIC TRANSMISSIONS DESIGNED TO USE ATF M-V (TYPE M5) MAY CAUSE SHIFT QUALITY COMPLAINTS.• USING ANY OTHER ATF OTHER THAN THE SPECIFIED ATF IN AUTOMATIC TRANSMISSIONS MAY CAUSE TRANSMISSION DAMAGE.• USING A GENERIC, MULTI-PURPOSE OR UNIVERSAL ATF MAY CAUSE TRANSMISSION DAMAGE.• DAMAGE TO THE TRANSMISSION CAUSED BY USING THE INCORRECT ATF, OR A GENERIC, MULTI-PURPOSE OR UNIVERSAL ATF WILL NOT BE COVERED BY WARRANTY.
01-003-15-30142017-05-25. Service bulletin. EQUIPMENT. USE THE FOLLOWING REPAIR PROCEDURE TO MINIMIZE THE NEED TO REPLACE THE CATALYST CONVERTER/EXHAUST PIPE WHEN REMOVING OXYGEN SENSORS AND/OR AIR FUEL RATIO SENSORS.
09-039-14-29232017-05-08. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; EQUIPMENT:ELECTRICAL. SOME VEHICLES MAY EXHIBIT BLUETOOTH® HANDS-FREE AND/OR TEXT MESSAGING RELATED CONCERNS. TO IMPROVE THE HANDLING OF BLUETOOTH® HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CRE-ATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM AS OF FEBRUARY 2010.
03-004-14-29592017-05-08. Service bulletin. EQUIPMENT. SOME VEHICLES MAY EXHIBIT A WHINING NOISE FROM THE REAR DIFFERENTIAL WHEN DRIVING.THE CONCERN MAY BE CAUSED BY IMPROPER TOOTH CONTACT PATTERN OF THE REAR DIFFERENTIAL GEAR FROM ABNORMAL WEAR. THIS ABNORMAL WEAR IS CAUSED BY GEAR TOOTH LAPPING COMPOUND (USED DURING THE PRODUCTION) BEING LEFT ON BEYOND THE ALLOWABLE AMOUNT. THE PRODUCTION CONTROL HAS BEEN IMPROVED TO REDUCE THE AMOUNT OF REMAINING LAPPING COMPOUND.
09-034-14-29562017-05-05. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. IN ACCORDANCE WITH FEDERAL REGULATIONS, FOLLOW THE PROCEDURE LISTED BELOW WHEN REPLACING A SPEEDOMETER.NOTE:•MAZDA VEHICLES ARE MANUFACTURED WITH TAMPER-PROOF SPEEDOMETERS.•WHEN A SPEEDOMETER IS REPLACED, THE NEW SPEEDOMETER WILL READ ZERO (0) MILES.•THIS PROCEDURE IS EXTREMELY IMPORTANT TO ACCURATELY REPRESENT ACTUAL VEHICLE MILEAGE.•PRIOR TO SPEEDOMETER REMOVAL, COMPLETE THE INFORMATION REQUIRED ON THE “SPEEDOMETER REPLACE-MENT LABEL”. •LABELS CAN ONLY BE ORDERED THROUGH MSTORE, NOT MDCS.
09-027-14-29352017-05-04. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. THIS SERVICE BULLETIN PROVIDES INFORMATION REGARDING THE PROPER USE OF THE DRIVER’S FLOOR MAT TO AVOID ANY POTENTIAL INTERFERENCE WITH THE FOOT PEDALS. THE FOLLOWING ARE POSSIBLE CAUSES OF FLOOR MAT INTERFERENCE, WHICH CAN BE AVOIDED WITH PROPER USAGE. • FLOOR MAT MOVES FORWARD DUE TO IMPROPER INSTALLATION. • INAPPROPRIATE FLOOR MAT (SUCH AS AFTERMARKET, NON-FACTORY-EQUIPPED, OR NON-GENUINE) IS USED. • FLOOR MAT IS STACKED ONE ON TOP OF ANOTHER.
00-002-14-29362017-05-04. Service bulletin. EQUIPMENT. MAZDA NORTH AMERICAN OPERATIONS RECEIVED MANY REQUESTS FROM OUR DEALERS ASKING US TO APPROVE ADDITIONAL ON-CAR BRAKE LATHES AS AN OPTION FOR MNAO AUTHORIZED EQUIPMENT. DUE TO YOUR FEEDBACK AND AFTER EVALUATING A FEW ON-CAR BRAKE LATHES, WE ARE PLEASED TO ANNOUNCE THAT WE HAVE ADDED THE PRO CUT ON-CAR BRAKE LATHE TO MNAO AUTHORIZED EQUIPMENT PROGRAM. THE ACCU-TURN IS STILL AN APPROVED BRAKE LATHE BUT IT IS NO LONGER AVAILABLE FOR PURCHASE FROM OUR VENDOR. IMPORTANT REMINDER – ROTORS MUST BE MACHINED USING A MAZDA APPROVED ON-CAR BRAKE LATHE OR WARRANTY CLAIMS ARE SUBJECT TO DENIAL OR DEBIT.
09-023-14-29242017-05-03. Service bulletin. EQUIPMENT. SOME CUSTOMERS MAY COMPLAIN THAT THE AMBIENT TEMPERATURE DISPLAY IS NOT ACCURATE, OR IT TAKES TOO LONG FOR THE DISPLAY TO SHOW ACTUAL TEMPERATURE.WHEN YOU ENCOUNTER A CUSTOMER WITH THIS CONCERN, FIRST VERIFY THE CONDITION WHEN THE CUSTOMER NOTICED THIS SYMPTOM. IF THE CONDITION IS SIMILAR TO THE FOLLOWING “CONTROL LOGIC OF AMBIENT TEMPERATURE” OR “DIF-FERENCE BETWEEN THE TEMPERATURE DISPLAY AND OTHERS”, ADVISE THE CUSTOMER THAT THIS IS A NOR-MAL CHARACTERISTIC OF THE VEHICLE AND NOT A MALFUNCTION.
09-012-14-28912017-04-27. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. WHEN REPLACING THE SIRIUSXM SATELLITE RADIO UNIT (OR A MAZDA CONNECT TUNER AND AMP UNIT (TAU)) WITH REPLACEMENT TUNER FOR ANY REASON, A CALL MUST BE MADE TO INFORM SIRIUSXM OF THE EXISTING RADIO ID AND THE NEW/ REPLACEMENT SAT RADIO ID AS SOON AS POSSIBLE TO ENSURE THE CUSTOMER LEAVES THE DEALERSHIP WITH ACTIVE (WORKING SAT RADIO.
00-004-12-27412017-04-26. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. MAZDA HAS DEVELOPED FACTORY RECOMMENDED SCHEDULED MAINTENANCE SERVICES THAT SUPPORT ALL MAJOR VEHICLE SYSTEMS. MAZDA RECOMMENDS DEALERS FOLLOW THE SCHEDULED MAINTENANCE TABLES AS CITED IN THE VEHICLE-SPECIFIC WORKSHOP MANUAL OR OWNER’S MANUAL. SERVICES PERFORMED OUTSIDE OF MAZDA’S FACTORY SCHEDULED MAINTENANCE ARE NOT RECOMMENDED. THESE SERVICES ARE UNNECESSARY AND CREATE UNNEEDED EXPENSES FOR YOUR CUSTOMERS.
07-002-13-28422017-04-24. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. A MUSTY/MILDEW TYPE ODOR MAY COME FROM THE VENTS WHEN THE AIR CONDITIONING (A/C) SYSTEM IS OPERATING. IT IS MOST NOTICEABLE WHEN THE A/C IS FIRST TURNED ON. THIS ODOR IS THE RESULT OF MOLD GROWTH IN THE A/C EVAPORATOR/COOLING UNIT WHICH IS CAUSED BY CONDENSATION, DUST, AND POLLEN WITHIN THE COOLING UNIT. THIS CONDITION IS USUALLY WORSE DURING HIGH HUMIDITY CONDITIONS. “MAZDA AIR COOLING COIL COATING” IS AVAILABLE TO ENCAPSULATE THE MOLD TO REDUCE ODORS. IF THE PRODUCT IS PROPERLY APPLIED, IT CAN EFFECTIVELY REDUCE THE MUSTY/MILDEW ODOR FOR UP TO THREE YEARS.NOTE:SEE PARTS INFORMATION FOR MAZDA AIR COOLING COIL COATING AND KIT PART NUMBERS.
09-018-13-28032017-04-14. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME CUSTOMERS MAY COMPLAIN THAT THE AMBIENT TEMPERATURE DISPLAY IS NOT ACCURATE, OR IT TAKES TOO LONG FOR THE DISPLAY TO SHOW ACTUAL TEMPERATURE. WHEN YOU ENCOUNTER A CUSTOMER WITH THIS CONCERN, FIRST VERIFY THE CONDITION WHEN THE CUSTOMER NOTICED THIS SYMPTOM. IF THE CONDITION IS SIMILAR TO THE FOLLOWING “CONTROL LOGIC OF AMBIENT TEMPERATURE” OR “DIFFERENCE BETWEEN THE TEMPERATURE DISPLAY AND OTHERS”, ADVISE THE CUSTOMER THAT THIS IS A NORMAL CHARACTERISTIC OF THE VEHICLE AND NOT A MALFUNCTION. IF THE CONDITION DOES NOT MEET THE FOLLOWING AND THE SENSOR MALFUNCTION IS SUSPECTED, MAKE SURE TO INSPECT THE SENSOR ACCORDING TO MS3 ONLINE OR WORKSHOP MANUAL (SECTION 09-22 AMBIENT TEMPERATURE SENSOR INSPECTION).
09-019-13-28052017-04-14. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. TO IMPROVE HANDLING OF CUSTOMER CONCERNS WITH HANDS-FREE (BLUETOOTH) VEHICLE SYSTEMS, MAZDA LAUNCHED A NEW SERVICE PROCEDURE AND PART EXCHANGE PROGRAM EFFECTIVE FEB. 08, 2010 ON APPLICABLE VEHICLES. DUE TO THE COMPLEXITY OF SOFTWARE AND HARDWARE AVAILABLE ON VARIOUS CELLULAR PHONES AND CELL PHONE PROVIDER NETWORKS, IT IS ESSENTIAL FOR CUSTOMERS TO CONTACT THE MAZDA HANDS-FREE SYSTEM CUSTOMER CARE NUMBER AT (800) 430-0153 OR, FOR CUSTOMERS REQUIRING ADDITIONAL RESOURCES, PLEASE DIRECT THEM TO “WWW.MAZDAUSA.COM/BLUETOOTH.” REPRESENTATIVES OF THE CUSTOMER CARE CENTER ARE KNOWLEDGEABLE ON VERIFYING APPROVED PHONES AND PROPERLY PAIRING (PROGRAMMING) SPECIFIC PHONES TO THE VEHICLE’S BLUETOOTH SYSTEM. THEY ARE ALSO BEST EQUIPPED TO RESOLVE A MAJORITY OF THE PAIRING ISSUES AND OTHER BLUETOOTH RELATED CONCERNS WHEN COMMUNICATING DIRECTLY WITH MAZDA CUSTOMERS.
00-001-13-2748A2017-04-14. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. MAZDA HAS DEVELOPED FACTORY RECOMMENDED SCHEDULED MAINTENANCE SERVICES THAT SUPPORT ALL MAJOR VEHICLE SYSTEMS. MAZDA RECOMMENDS DEALERS FOLLOW THE SCHEDULED MAINTENANCE TABLES AS CITED IN THE VEHICLE-SPECIFIC WORKSHOP MANUAL OR OWNER’S MANUAL. SERVICES PERFORMED OUTSIDE OF MAZDA’S FACTORY SCHEDULED MAINTENANCE ARE NOT RECOMMENDED. THESE SERVICES ARE UNNECESSARY AND CREATE UNNEEDED EXPENSES FOR YOUR CUSTOMERS.
09-003-13-27762017-04-14. Service bulletin. EQUIPMENT:MECHANICAL. WHEN DEALING WITH CUSTOMER COMPLAINTS OF EXCESSIVE CONDENSATION AND/OR WATER WITHIN THE HEADLAMP UNIT, FIRST DETERMINE IF ALL THE BULB SOCKETS ARE PRESENT AND CORRECTLY INSTALLED. IN MOST CASES YOU WILL FIND THAT THE BULB SEAL NO. 1 (A) OR HID BULB SEAL NO. 1 (B) AND BULB SEAL NO. 2 (C) SOCKET COVERS HAVE NOT BEEN CORRECTLY INSTALLED OR ARE MISSING DUE TO IMPROPER PRIOR REPAIRS (I.E., CUSTOMER REPLACING THE HEADLAMP BULBS OR BODY SHOP NOT TRANSFERRING THEM WHEN REPLACING THE HEADLAMP UNIT(S) DUE TO A COLLISION). ANY DAMAGE CAUSED BY MISSING SOCKET COVERS, HID MODULE SEAL (D), OR MISSING BUMPER BRACKETS (E) IS NOT COVERED BY WARRANTY POLICY.
09-005-13-27812017-04-13. Service bulletin. EQUIPMENT. THIS SERVICE BULLETIN PROVIDES INFORMATION REGARDING THE PROPER USE OF THE DRIVER’S FLOOR MAT TO AVOID ANY POTEN-TIAL INTERFERENCE WITH THE FOOT PEDALS. THE FOLLOWING ARE POSSIBLE CAUSES OF FLOOR MAT INTERFERENCE, WHICH CAN BE AVOIDED WITH PROPER USAGE.•FLOOR MAT MOVES FORWARD DUE TO IMPROPER INSTALLATION.•INAPPROPRIATE FLOOR MAT (SUCH AS AFTERMARKET, NON-FACTORY-EQUIPPED, OR NON-GENUINE) IS USED.•FLOOR MAT IS STACKED ONE ON TOP OF ANOTHER.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.