WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Mazda Mazda6

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

516 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
09-007-18-3422a2018-04-23. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Some customers may experience a navigation system screen that shows the wrong location. This concern is due to poor reception of the GPS signals. To eliminate this concern, the CMU hardware has been modified.
09-019-18-34502018-04-23. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This service bulletin provides information regarding the proper use of the driver's floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another. Use these points at your dealership to protect our mutual operations and to help ensure our customers' safety.
09-014-18-34432018-04-23. Service bulletin. STRUCTURE. When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
09-011-18-34482018-04-23. Service bulletin. EXTERIOR LIGHTING:TAIL LIGHTS; EXTERIOR LIGHTING:HEADLIGHTS. Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between the inside and the outside of the light housing. It is normal for very small water drops to appear incertain locations on the light units where the air is stagnant (condensation), making the lens look whitish (fog). This happens mostly in the corners and narrow spaces, and will typically clear during warmer ambient temperatures, or when the lights have been on for some time.
02-005-18-34442018-04-23. Service bulletin. SUSPENSION. Beginning with the CX-5, grip type front and rear stabilizer bushings have been incorporated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.
00-001-18-34462018-04-23. Service bulletin. EQUIPMENT. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
09-015-18-34452018-04-23. Service bulletin. SEATS. At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface.
09-010-18-34402018-04-23. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.504 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda's continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on.
01-006-18-34292018-04-23. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of the following DTC(s) stored in memory. P0300 - Random misfire detected P0301 - Cylinder No.1 misfire detected P0302 - Cylinder No.2 misfire detected P0303 - Cylinder No.3 misfire detected P0304 - Cylinder No.4 misfire detected. This may be caused by frozen water accumulated in the main silencer, restricting exhaust flow.
09-003-18-3405b2018-04-23. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Some customers may complain that the Voice Recognition system does not recognize "Address" or "New Destination" navigation voice commands. This may be caused by faulty navigation SD card software. TheSD card has been updated to eliminate this concern.
09-005-18-34142018-03-05. Service bulletin. SEATS:FRONT ASSEMBLY:POWER ADJUST. Some vehicles may exhibit excessive operating noise when sliding the driver and/or passenger power seat(s) back and forth. The noise may be caused by cable vibration, which transmits power from the motor to the gears. The cable vibrates inside the cable casing due to inadequately wrapped fabric around the cable. To eliminate this concern, the power seat cable has been changed to a type that produces less friction and noise.
15-001-18-33692018-03-05. Service bulletin. FORWARD COLLISION AVOIDANCE: SENSING SYSTEM: CAMERA. Some customers may experience the following symptom relating to the Forward Sensing Camera (FSC)with DTC C1001:92 [Forward sensing camera (FSC) poor field of view] stored in memory.When the visibility out the windshieldis poor (i.e. fog or raining at night), the following warning lights mayilluminate. Master Warning Light High Bean Control Warning Light Lane-keep Assist System (LAS) Lane Departure Warning System (LDWS) Warning Light Smart Brake Support/Smart City Brake Support (SBS/SCBS) Indicator LightThis is caused by the control logic of the FSC being too sensitive. To correct this issue, the control logic ofthe FSC has been modified.
09-003-18-3405a2018-03-05. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some customers may complain that the Voice Recognition system does not recognize "Address" or "New Destination" navigation voice commands. This may be caused by faulty navigation SD card software. The SD card has been updated to eliminate this concern.
09-003-18-34052018-03-05. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some customers may complain that the Voice Recognition system does not recognize "Address" or "NewDestination" navigation voice commands. This may be caused by faulty navigation SD card software. TheSD card has been updated to eliminate this concern.
09-002-18-34102018-03-05. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. After the installation of a new instrument cluster, the message "Fctry" or "Factory" is displayed instead ofthe odometer. This concern may also occur when a room fuse is installed in a new vehicle.Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required.NOTE: The concern is applicable to Calsonic Kansei instrument clusters. Not all trim levels are affected.CX-3 shown:Vehicles having this concern should have their vehicle repaired using the following procedure.
09-001-18-33872018-03-05. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during coldtemperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interiorwarms up. This is caused by some for the MAZDA CONNECT navigation system SD cards beingmanufactured with improper hardware, resulting in a data reading error during cold temperatures. To correctthe concern, the SD card hardware has been changed.
02-002-18-3300d2018-03-05. Service bulletin. SUSPENSION:FRONT:SHOCK ABSORBER. Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving onrough roads and/or when turning the steering wheel while the vehicle is stopped.The noise may be due to: Upper front strut bearing (A) damage. (CX-5 and Mazda6) Squeak type noise between the front strut bearing and coil spring. (CX-3, CX-5 and Mazda6) The bump stopper (C) may be contacting the strut bearing when the front shock absorber is compressed, causing a popping noise. (Mazda6 only) The front lower arm bushing (D) is making a creak type noise in wet road conditions. (CX-5 and Mazda6).Front Shock Absorber Front Lower Arm To eliminate the noise, the following mass-production changes have been made: 1. The material and production method of the front strut bearing (A) has been changed. (CX-5 and Mazda6) 2. A protector has been installed onto the coil spring. (CX-5 and Mazda6) 3. The shape of the bump stopper (C) will be modified in the future. (Mazda6 only) 4. The shape of the coil spring has been changed. (CX-3 only) 5. Friction of the lower arm bushing has been reduced by adding a dry coating. (CX-5 and Mazda6). NOTE: The piston rod nut (B) requires replacement.
MT-021-172018-02-26. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure.
MT-001-182018-02-26. Service bulletin. ELECTRICAL SYSTEM. When installing a navigation SD card, the center display may show error message "Invalid SD Card". This may be caused by: The navigation SD card lock tab is locked.The navigation SD card has a VIN mismatch due to SD card swapping.The navigation SD card has a malfunction.
SA-001-182018-02-26. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. The MAZDA MOBILE START (MMS) is currently experiencing a system disruption. User web portal and Call center web portal functions are affected. Mazda is working on this issue and will notify dealers when MMS service has been fully restored. We apologize for any inconvenience this may have caused you or your dealer.
15-006-17-3388a2018-02-26. Service bulletin. ELECTRICAL SYSTEM. Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. The following DTCs are stored in memory: U3000:98 - Forward sensing camera (FSC) stops functioning due to temporary high temperature. U3000:04 - Forward sensing camera (FSC) internal malfunction. The combination of warning lights mentioned by the customer may include: SCBS/SBS, LAS/LDWS, HBC, Master Warning LightInstrument Cluster Multi-Information Display (if equipped) warning messages may include: Forward Smart City Brake Support Malfunction, Smart Brake System Malfunction, Front Camera Sensor System Malfunction, MAZDA CONNECT center display warning messages may include: High Beam Control [HBC] / Lane-keep Assist System [LAS] Malfunction. Have the vehicle checked by a dealer if this indicator stays on. Smart City Brake Support [SCBS] Malfunction. Have the vehicle checked by a dealer immediately. Note: The center display Warning Messages are only displayed when the customer selects Applications>Vehicle Status Monitor>Warning Guidance>Warnings. This condition may be caused by FSC control logic that is too sensitive. When the FSC detects DTCU3000:98 during high temperature, it stops the internal communication and stores DTC U3000:04. DTC U3000:04 will not clear and SCBS/SBS, LAS/LDWS, and/or HBC functions will not resume until the ignition switch has been turned OFF, even if the temperature of the FSC cools. Before FSC Reprogramming: The warning lights/messages will be displayed until the FSC cools and the ignition is turned OFF, then back ON. Instrument Instrument Cluster Warning Lights and MAZDA CONNECT Warning Messages Cluster Warning Messages Warning Lights (With Multi-Information Display) (Without Multi-Information Display), Note: These Warning Messages are displayed when the customer selects Applications>Vehicle Status Monitor>Warning Guidance>Warnings.
06-001-17-3307b2018-02-26. Service bulletin. STEERING: STEERING WHEEL/HANDLE BAR. Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
MT-016-172017-12-14. Service bulletin. FORWARD COLLISION AVOIDANCE: SENSING SYSTEM. The Smart City Brake Support (SCBS) system alerts the driver of a possible collision using an indication in the display and a warning sound when the Forward Sensing Camera (FSC) detects a vehicle ahead and determines that a collision with a vehicle ahead is imminent. In addition, the system reduces damage in the event of a collision by operating the brake control when the system determines that a collision is unavoidable. It may also be possible to avoid a collision depending on the relative speed between your vehicle and the vehicle in front of you. In addition, when the driver depresses the brake pedal, the brakes are applied firmly and quickly to assist.
15-005-17-3358b2017-11-14. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Some customers may complain that the BSM indicator light on the outer mirror glass does not illuminate when: ? Customer vehicle (A) is slowly passing other vehicle, even if the vehicle is still in the alert area.? Adjacent vehicle (B) driving at same speed, even if the vehicle is still in the alert area. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been modified to address these customer concerns.
15-005-17-3358a2017-11-14. Service bulletin. VISIBILITY; ELECTRICAL SYSTEM. Some customers may complain that when passing a vehicle slowly, even if the vehicle is still in the alert area, the BSM indicator light on the outer mirror glass does not illuminate. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been modified to address this customer concern.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.