WenmarOpen by Wenmar Pro

Service bulletins for the 2020 Mazda Mazda3

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

726 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
09-007-20-3674a2021-01-05. Service bulletin. EQUIPMENT; SEATS. At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.
07-006-20-37582021-01-05. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE; ENGINE AND ENGINE COOLING; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some customers may complain that after accelerating in hot weather, the A/C blows warm air for a longer time than other models. This is caused by improper control software of the PCM not allowing the A/C compressor to resume properly after acceleration. To eliminate this concern, the control software of the PCM has been modified.
05-002-20-3704b2021-01-05. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE; POWER TRAIN. Some customers may complain about a surging at low speeds and during acceleration. This surging is in the longitudinal direction, felt about 2 cycles per second, and occurs in the locked up 1st gear. This may be caused by the torque fluctuation and the torsional resonance in the torque converter. To correct this concern, the PCM software has been modified to reduce the torque fluctuation.
01-010-20-3706a2021-01-05. Service bulletin. ELECTRICAL SYSTEM. Some customers may experience a no start because the battery is discharged after the vehicle is parked for more than 8 hours. This may be caused by one or more of the following, resulting in excessive parasitic draw (dark current) on the battery.
SA-057-20a2020-12-04. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT. HVAC SYSTEM BLOWS HOT AIR UNDER ACCELERATION. Some customers may complain that the HVAC system blows hot air on occasion (blows cold air, then hot air, then cold air again). The customer may notice that it is more pronounced when they first start driving the vehicle and/or when accelerating.
SA-046-20b2020-12-04. Service bulletin. FORWARD COLLISION AVOIDANCE: SENSING SYSTEM: CAMERA; EQUIPMENT ADAPTIVE/MOBILITY; VISIBILITY. FORWARD SENSING CAMERA (FSC) DYNAMIC AIMING NOT COMPLETED AND/OR DTC B14F0:76 STORED. CAUTION: DO NOT turn the igintion OFF after dynamic aiming starts until aiming has completed or aiming timeout. If the ignition is turned OFF, the VCM will store B14F0:76 and FSC aiming will not complete. FSC dynamic aiming (mid-drive aiming) may not complete if the vehicle is driven on a road as described below: The road lane markings are covered by snow and are not visible. There are no road lane markings on the road surface. The road is winding and the vehicle cannot drive straight (300 m / 984 ft or more turning radius is required).
SA-031-20j2020-12-04. Service bulletin. LATCHES/LOCKS/LINKAGES:DOORS:LOCK; EQUIPMENT ADAPTIVE/MOBILITY; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM:SOFTWARE. IMPORTANT NOTE: Some 2020 Mazda3 vehicles may have incorrect infotainment software version 10042 installed. The incorrect software will cause MyMazda App Connected Vehicle enrollment errors. Go to SSPC1. Some customers may complain about any of the following: Infotainment Center Display does not provide the Authorization Code during the MyMazda App Connected Vehicle enrollment (and Software Update Error message on 2020 Mazda3 only). Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF
SA-031-20i2020-12-04. Service bulletin. ENGINE AND ENGINE COOLING; EXTERIOR LIGHTING; ELECTRICAL SYSTEM:SOFTWARE. IMPORTANT NOTE: Some 2020 Mazda3 vehicles may have incorrect infotainment software version 10042 installed. The incorrect software will cause MyMazda App Connected Vehicle enrollment errors. Go to SSPC1. Some customers may complain about any of the following: Infotainment Center Display does not provide the Authorization Code during the MyMazda App Connected Vehicle enrollment (and Software Update Error message on 2020 Mazda3 only). Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF
SA-007-20m2020-12-04. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. MAZDA CONNECTED SERVICES - FREQUENTLY ASKED QUESTIONS (FAQ). General Questions, Setup and Getting Started, Registration / Enrollment, WI-FI General Information, WI-FI How-To, WI-FI Trial Period, Interacting With The App, Service Issues, Troubleshooting, Dealer Processes, Educational Videos, Resources
SA-003-20e2020-12-04. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. When the body control module (BCM) has been replaced or reprogrammed and the software is updated to the file names shown below, DTC U2050:55-BCM (Activation of remote control not implemented) may be stored in memory without any warning indication for the driver. This is caused by a communication error between the telematics communication unit (TCU) and BCM when the control software in them are not of the version being ready for activation of the connected service.
09-021-20-3714a2020-12-03. Service bulletin. EQUIPMENT:ELECTRICAL:ANTENNA; EQUIPMENT ADAPTIVE/MOBILITY. Some customers may experience the master warning light and/or the "In-Vehicle Network Malfunction" warning message in the instrument cluster on with DTC B119F:01, B119F:13 and/or B119F:2B stored when the vehicle position cannot be displayed correctly. • B119F:01 (TCU - Tel antenna No. 1 malfunction) • B119F:13 (TCU - TEL antenna No.1 circuit malfunction) • B119F:2B (CMU - GPS antenna signal circuit malfunction) This concern may be caused by incoming noise disturbing the reception of GPS signals, resulting in the wrong vehicle location and the DTC stored. To eliminate this concern, the GPS antenna has been modified.
01-006-20-3695b2020-12-03. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. Some vehicle may exhibit a tapping noise from the engine during idling; etc., and synchronized to the engine rpm. The tapping noise may be caused by the switchable hydraulic lash adjuster (HLA), which may not work properly due to air bubbles accumulated in the oil passage in it.
SA-027-20f2020-11-04. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM; BACK OVER PREVENTION; EQUIPMENT. MAZDA CONNECT SYMPTOM TROUBLESHOOTING (7TH GENERATION VEHICLES). Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure. Index: No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. 6 Bluetooth device will not pair No. 7 Incorrect GPS position No. 8 Voice Recognition Does Not Work No. 9 Cannot Make a Hands-Free Call No. 10 Cannot Play Bluetooth Audio No. 11 How to Check Navi SD Card VIN Lock
SA-071-202020-11-04. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. Currently, the instructions on MGSS recommend the use of Loctite 962T or equivalent when installing a SKYACTIV cylinder head, but it is no longer available. The following 3 adhesives are alternatives available as an equivalent to Loctite 962T: Loctite 272, Loctite 518 Threebond TB-1386H
SA-070-202020-11-04. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. APPLE CARPLAY / ANDROID AUTO FREQUENTLY ASKED QUESTIONS (FAQ): NOTE: The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. See Activation instructions on MGSS - Infotainment - MAZDA CONNECT Updates - Apple Carplay / Android Auto MDARS Activation Instructions
SA-069-202020-11-04. Service bulletin. EQUIPMENT. ACCESSORY INSTRUCTIONS LOCATION: Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.mazdausa.com
SA-031-20f2020-11-04. Service bulletin. ELECTRICAL SYSTEM. CONNECTED VEHICLE SYMPTOM TROUBLESHOOTING: IMPORTANT NOTE: Some 2020 Mazda3 vehicles may have incorrect infotainment software version 10042 installed. The incorrect software will cause MyMazda App Connected Vehicle enrollment errors. Go to SSPC1. Some customers may complain about any of the following: Infotainment Center Display does not provide the Authorization Code during the MyMazda App Connected Vehicle enrollment (and Software Update Error message on 2020 Mazda3 only). Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF
SA-007-20l2020-11-04. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. MAZDA CONNECTED SERVICES - FREQUENTLY ASKED QUESTIONS (FAQ). General Questions, Setup and Getting Started, Registration / Enrollment, WI-FI General Information, WI-FI How-To, WI-FI Trial Period, Interacting With The App, Service Issues, Troubleshooting, Dealer Processes, Educational Videos, Resources
09-034-20-37432020-11-04. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Some customers may experience an “In-Vehicle Network Malfunction” message appearing in the instrument cluster. This concern occurs when turning the ignition on or starting the engine when the battery is at 8 volts or lower (vehicle is in sleep mode), then it is charged to normal voltage while connected to the vehicle. NOTE: This concern will not occur if the battery is charged when removed from the vehicle. This concern is caused by improper telematics communication unit control software. To eliminate this concern, the telematics communication unit control software has been modified.
09-033-20-37422020-11-04. Service bulletin. ELECTRICAL SYSTEM. Some vehicles may exhibit that DTC B2002:49 will not clear with the Mazda Modular Diagnostic System (MMDS). Applicable vehicles are equipped with the Electrical supply unit (ESU) BCKA-67-5Z0B. • DTC B2002:49 [BODY CONTROL MODULE (BCM)] - Electrical supply unit (ESU) internal malfunction (No warning/indicator light illumination) This is caused by improper control software of the ESU. To eliminate this concern, the control software of the ESU has been modified.
09-018-20-3690a2020-11-04. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Some customers may notice white lines appearing across the instrument cluster (as shown below). The white lines may be caused during the production process where poor contact occurs at the internal LCD terminals.
07-005-20-37452020-11-03. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT:APPLIANCE:AIR CONDITIONER; ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT ADAPTIVE/MOBILITY. Some customers may complain that the A/C blows warm air while idling after restarting a warm engine. This is caused by improper control software of the PCM not allowing the active air shutter to open properly, resulting in lower cooling performance at idle. To eliminate this concern, the control software of the PCM has been modified.
16-001-20-3683c2020-11-03. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE. AUDIO, NAVIGATION AND PHONE CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM (7TH GENERATION MODELS). Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 7000C0A-NA01_11012 or later). NOTE: Device compatibility can be found at connect.mazda.com - Support - Compatibility.
16-001-20-3683b2020-11-03. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE; ELECTRICAL SYSTEM:SOFTWARE. AUDIO, NAVIGATION AND PHONE CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM (7TH GENERATION MODELS). Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 7000C0A-NA01_11012 or later). NOTE: Device compatibility can be found at connect.mazda.com - Support - Compatibility. 16-001-20-3683c
SA-060-20c2020-10-05. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. When replacing the Body Control Module (BCM) in a 7th generation vehicle, it needs to be configured and the instructions in the Workshop manual on MGSS are incorrect. Use the instructions in the Repair Procedure below to configure the new BCM.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.