WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Mazda Mazda3

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

744 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
07-007-19-36382019-11-21. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; ENGINE. Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a plugged heater core. For 2014-2016 Mazda6 and 2013-2016 (US spec) / 2017 (Mexico spec) CX-5, the CHECK ENGINE light may turn on with DTC P011A:00 (ECT sensor No.1/No.2 performance problem) stored at the same time. NOTE: Refer to TSB 01-015/15 if the customer is using a block heater at temperatures below freezing. To solve this concern, two mass production changes have been implemented. a) The concentration of the coolant has been increased so that the amount of the contained anti-rust additive is higher. b) The composition of the coolant has been changed (the ratio of the anti-rust additive has increased).
SSPB6b2019-11-01. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. For certain 2014-2016 Mazda3 vehicles, the warranty coverage for specific repair of the Mazda Connect Center Display is extended to 7 years (84 months) from the original warranty start date, with no mileage limitation. On certain 2014-2016 Mazda3 vehicles, the Mazda Connect touch screen in the center display may not accept touch commands properly or may operate by itself (ghost touch). The ITO (Indium Tin Oxide) film of touch screen may be corroded due to moisture, which may adhere on the lens of touch screen during the cleaning process at the plant. The corrosion may allow the electrostatic capacity to vary without any input, causing the malfunction of touch screen.
SSPB6a2019-11-01. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. On certain 2014-2016 Mazda3 vehicles, the Mazda Connect touch screen in the center display may not accept touch commands properly or may operate by itself (ghost touch). The ITO (Indium Tin Oxide) film of touch screen may be corroded due to moisture, which may adhere on the lens of touch screen during the cleaning process at the plant. The corrosion may allow the electrostatic capacity to vary without any input, causing the malfunction of touch screen.
MT-003-192019-10-30. Service bulletin. ENGINE AND ENGINE COOLING. Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary:
MT-002-192019-10-04. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.
04-005-19-35122019-10-04. Service bulletin. SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:CALIPER; SERVICE BRAKES, HYDRAULIC. Some vehicles may exhibit a rattle / knock noise from the front disc brake caliper (1) when driving on a rough road surface.This is caused by the slide pin (1) hitting the mounting support (2) due to insufficient holding power of the dust boots (3) when a shock (4) is applied from the road. To eliminate this concern, the dust boots have been modified to increase holding power.
SA-040-192019-09-23. Service bulletin. STRUCTURE:BODY:HOOD; ENGINE AND ENGINE COOLING. Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
07-005-19-36322019-09-23. Service bulletin. EQUIPMENT; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some customers may complain about no cool air from the vents when the air conditioner (A/C) is ON. This concern may be caused by A/C refrigerant leaking from the evaporator at the joint between the tubes and the header due to improper brazing. To correct the problem, the configuration of the header has been changed to improve the brazing performance in this area.
01-016-19-36272019-08-30. Service bulletin. ENGINE AND ENGINE COOLING. Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded. P0524:00 - Engine oil pressure too low. This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time.
09-010-19-36242019-08-15. Service bulletin. VISIBILITY; SERVICE BRAKES, HYDRAULIC; EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. Customers concern can be resolved by sanding off paint at ground point (3) where attachment bolt (4) is seated. After installing the bolt (4), apply touch-up paint to the exposed base material area of the front fender stay.
09-026-19-36132019-08-02. Service bulletin. STRUCTURE; VISIBILITY:WINDSHIELD. Some vehicles may exhibit the cushion tape (1) attached to the front end of dashboard coming off and showing at the base of the windshield. This is caused by the cushion tape peeling off from the end(s) due to interference with the windshield and vehicle vibration (CX-5/Mazda6) or from the gap between the dashboard and the cushion tape because there there is no rib (1) at the dashboard ends (Mazda3). To prevent the tape from peeling off, both ends of the cushion tape are now folded over to the back side of the dashboard (CX-5/Mazda6) or stapled (Mazda3).
07-002-19-36162019-08-01. Service bulletin. EQUIPMENT; EQUIPMENT:APPLIANCE:AIR CONDITIONER. A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. "Mazda Air Cooling Coil Coating" is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.
SA-031-192019-08-01. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM. Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting.
SA-029-19a2019-08-01. Service bulletin. EQUIPMENT. The database error discovered with IDS 114.00-114.02 release has been fixed with IDS 114.04 release and is now available for download.
SA-029-192019-08-01. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. The Recall can be performed after removing IDS 114 and installing IDS 113. This SA will be updated when more information is available.
SA-003-192019-08-01. Service bulletin. FORWARD COLLISION AVOIDANCE: SENSING SYSTEM: CAMERA; FORWARD COLLISION AVOIDANCE. Some vehicles may have one of the following DTCs stored in memory: C1001:92 - Forward sensing camera (FSC) poor field of view. B14F0:92 - General temporary failure in forward sensing camera (FSC). DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details. If the vehicle has this DTC, DO NOT replace the FSC. Read below.
SSPB62019-07-01. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ELECTRICAL SYSTEM. Regarding the recently announced 2014-2016 Mazda3 - Mazda Connect Touch Screen Concern Warranty Extension Program - Special Service Program (SSP) B6, Mazda is facing supply delays due to supplier production limitations. Mazda is working directly with the supplier to resolve the issue and will expedite supply as quickly as possible. A subsequent announcement will be sent with timing details once the supply delay is resolved and owners of subject vehicles are notified.
09-025-19-36072019-07-01. Service bulletin. SEATS. Some vehicles may exhibit a condition where the front seat cushion trim comes off the seat frame at the front end. This may be found on vehicles with all types of the seat trims (leather, leatherette and fabric). The front seat cushion is attached to the seat frame using folding collars.This is caused by the collars slipping out of the seat frame when an excessive force is applied to the seat cushion.
09-024-19-36052019-07-01. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. This TSB has been superceded by SSPB6 - MAZDA CONNECT TOUCH SCREEN CONCERN WARRANTY EXTENSION SPECIAL SERVICE PROGRAM.
09-022-19-35992019-07-01. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.335C or later). NOTE:For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda’s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on. Updating MAZDA CONNECT to the latest version will erase any customization created by unauthorized software.Unauthorized customization software will not work on the latest version of MAZDA CONNECT software. The latest version of MAZDA CONNECT software cannot be rolled back to an earlier version. Mazda does not recommend unauthorized customization of MAZDA CONNECT due to the possibility of unexpected problems. Any issues related to this will not be covered under Mazda warranty policy.
05-005-19-35692019-07-01. Service bulletin. POWER TRAIN. Some vehicles may exhibit one of the following concerns: Sometimes the shifter may jump out of 3rd gear over a road bump when accelerating after deceleration at 25-40 mph (40-65 km/h), Hard to shift into 3rd, 4th, 5th, and/or 6th gear, Shift lever vibrates when driving in 3rd or 4th gear. This is caused by inappropriate transmission internal parts.
SSPB62019-06-01. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. We are launching this Warranty Extension on May 23, 2019 and mailing to customers before the end of June, 2019. Until owners are notified, repairs can be performed under this SSP. Mazda Motor Corporation is extending the warranty coverage for a specific concern regarding the Mazda Connect Center Display on certain 2014-2016 Mazda3 vehicles produced from June 11, 2013 through September 3, 2016. Please refer to the Parts and Warranty page for specific production date ranges for MC and MMVO produced vehicles as they are different. Concern Outline On certain 2014-2016 Mazda3 vehicles, the Mazda Connect touch screen in the center display may not accept touch commands properly or may operate by itself (ghost touch). The ITO (Indium Tin Oxide) film of the touch screen may be corroded due to moisture, which may adhere on the lens of the touch screen during the cleaning process at the plant. The corrosion may allow the electrostatic capacity to vary without any input, causing the malfunction of the touch screen. This warranty extension program applies only to the repair of the center display with this concern. This is a warranty extension for the specified repair only. Inspection and replacement of non-failed parts will not be eligible for reimbursement to the dealer or customer. This program extends the warranty period for actual failures due to defects in workmanship or materials in accordance with the Mazda Warranty Policy and Procedures.
06-002-19-3585a2019-05-31. Service bulletin. STEERING; STEERING: STEERING WHEEL/HANDLE BAR. Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
SA-006-19a2019-05-30. Service bulletin. BACK OVER PREVENTION; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle.
05-004-19-34662019-05-30. Service bulletin. POWER TRAIN. Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on P0877:00 - Oil pressure switch No. 4 (oil pressure switch B) stuck on P0780:00 - Gear shifting malfunction P1738:00 - Automatic transaxle internal malfunction This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to the instructions on MGSS (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [FW6A-EL/FW6AX-EL]) or (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [EW6A-EL/EW6AX-EL]) for proper diagnosis and repair procedure.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.