Service bulletin SSPB6

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10160602
Published by NHTSA	2019-06-01
Manufacturer's number	SSPB6
Manufacturer's date	2019-05-06
NHTSA component	EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY

NHTSA's summary

We are launching this Warranty Extension on May 23, 2019 and mailing to customers before the end of June, 2019. Until owners are notified, repairs can be performed under this SSP. Mazda Motor Corporation is extending the warranty coverage for a specific concern regarding the Mazda Connect Center Display on certain 2014-2016 Mazda3 vehicles produced from June 11, 2013 through September 3, 2016. Please refer to the Parts and Warranty page for specific production date ranges for MC and MMVO produced vehicles as they are different. Concern Outline On certain 2014-2016 Mazda3 vehicles, the Mazda Connect touch screen in the center display may not accept touch commands properly or may operate by itself (ghost touch). The ITO (Indium Tin Oxide) film of the touch screen may be corroded due to moisture, which may adhere on the lens of the touch screen during the cleaning process at the plant. The corrosion may allow the electrostatic capacity to vary without any input, causing the malfunction of the touch screen. This warranty extension program applies only to the repair of the center display with this concern. This is a warranty extension for the specified repair only. Inspection and replacement of non-failed parts will not be eligible for reimbursement to the dealer or customer. This program extends the warranty period for actual failures due to defects in workmanship or materials in accordance with the Mazda Warranty Policy and Procedures.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Equipment and accessories

Vehicles listed
MAZDA MAZDA3	2014, 2015, 2016

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
SA-027-24	2024-05-04. Service bulletin. Some customers may complain about infotainment center display. Peeling, spider cracks and white dots.
SA-008-24	2024-03-06. Service bulletin. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
SA-032-23a	2023-11-02. Service bulletin. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
09-032-23	2023-10-05. Service bulletin. SERVICE BULLETIN 09-031/20 ISSUED ON 09/21/20 IS NO LONGER VALID. IT IS SUPERCEDED BY RECALL 6023G (“2014-2018 MAZDA3 AND 2016-2021 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY”).
09-031-20b	2023-08-04. Service bulletin. Some vehicles may exhibit a distorted image or no image from the rear mount camera when shifted into reverse. Due to friction, the coating of camera socket terminals may wear out, creating high electrical resistance. NOTE: The icons and the messages are displayed normally.
09-031/20a	2023-08-04. Service bulletin. Be advised that TSB "09-031/20 - REAR MOUNT CAMERA IMAGE NOT CLEAR/NO IMAGE ON SCREEN" is no longer valid and has been superseded by "RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY". Use the link below to view the recall: RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY
SA-036-23	2023-07-05. Service bulletin. Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way. NOTE: The antistatic effect does not deteriorate with this procedure.
SA-016-23	2023-04-04. Service bulletin. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method. B. Auxiliary Key Code Cut Method
SA-001-23a	2023-02-02. Service bulletin. Some customers may complain about infotainment center display: - Ghost Touch - DTC B108E:04 may be stored (Touch screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: DO NOT replace the infotainment center display assembly. Low cost repair kits are available to repair the infotainment center display screen.
SA-001-23	2023-02-02. Service bulletin. Some customers may complain about infotainment center display: - Ghost Touch - DTC B108E:04 may be stored (Touch screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: DO NOT replace the infotainment center display assembly. Low cost repair kits are available to repair the infotainment center display screen.