Service bulletins for the 2015 Mazda Mazda3
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
744 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| 07-007-17-3384 | 2017-10-21. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a clogged heater unit. For Mazda6 and CX-5, the check engine light may illuminate with the DTC P011A:00 stored at the same time. P011A:00 ECT sensor No.1/No.2 performance problem. NOTE: Refer to TSB 01-015/15 if the customer is using a block heater at temperatures below freezing. |
|---|---|
| 01-008-17-3376 | 2017-10-21. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded. P0524:00 - Engine oil pressure too low. This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time. |
| 04-002-17-3316a | 2017-10-21. Service bulletin. SERVICE BRAKES, HYDRAULIC. Some vehicles may exhibit a squeak noise when applying the brakes and/or groove marks (A) on the front disc plates. This is caused by abrasive metal from the front disc plate sticking to the brake pad, which damages the disc plate over time. To correct the problem, a modified brake pad is being used. |
| 09-032-17-3372 | 2017-10-21. Service bulletin. VISIBILITY:POWER WINDOW DEVICES AND CONTROLS. Some vehicles may experience one or more of the following conditions with the driver and/or passenger side power window(s): ? The window glass will not raise/lower. The window suddenly stops operating while being raised/lowered. The window glass gets stuck where it stopped operating or falls down in the door. This concern is caused by the window regulator cable end becoming disconnected from the fixing point due to improper caulking. The production facility has been improved to prevent the improper caulking of the window regulator cable. |
| 09-017-17-3347b | 2017-10-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. All Mazda Connect vehicles in new car inventory must be updated to this software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. NOTE: If the customer has customized MAZDA CONNECT with something like a different background using unauthorized software, make sure they know the following information before updating MAZDA CONNECT to avoid any issues later on. |
| 05-002-17-3355a | 2017-10-21. Service bulletin. STEERING:GEAR BOX (OTHER THAN RACK AND PINION). Some vehicles may exhibit one of the following concerns: Sometimes the shifter may jump out of 3rd gear over a road bump when accelerating after deceleration at 25-40 mph (40-65 km/h), Hard to shift into 3rd, 4th, 5th, and/or 6th gear, Shift lever vibrates when driving in 3rd or 4th gear. This is caused by inappropriate transmission internal parts. |
| 01-004-17-3317a | 2017-10-21. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Some vehicles may experience an engine that runs rough and the check engine light on with DTCs P0201 and P0204 or P0202 and P0203. NOTE: Engine misfire related DTCs (P0301, P0302, P0303, P0304) are usually stored at the same time. P0201:00 : Fuel injector circuit/open cylinder No.1 P0202:00 : Fuel injector circuit/open cylinder No.2 P0203:00 : Fuel injector circuit/open cylinder No.3 P0204:00 : Fuel injector circuit/open cylinder No.4 This concern may be caused by an internal failure of the PCM (DENSO produced only). To correct the concern, the PCM internal failure has been eliminated. |
| 09-028-17-3363 | 2017-10-21. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. Some customers may experience that one or more of the door glasses will not open due to becoming stuck in the glass run channel. The root cause is still under investigation. To correct the problem, the parts source will be changed. |
| 08-002-17-3312a | 2017-10-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. When monitoring the resistance of the air bag modules and pre-tensioner seat belts, the Mazda Modular Diagnostic System (M-MDS) may display a value of only 1/100th of the actual resistance value. This is caused by improper SAS control unit software. To eliminate this from occurring in the future, the SAS control unit software has been modified. |
| 04-003-17-3331a | 2017-10-21. Service bulletin. SERVICE BRAKES. Some vehicles may experience a squeaking/grinding noise from the rear brake even after the brake pedal is released. Upon inspection, the caliper mounting support is corroded and one of the disc pad is abnormally worn out (A). This is caused by vehicle usage in an area using road salt. The surface of the mounting support may swell from corrosion causing premature disc pad wear and brake noise. To correct the problem, an improved caliper mounting support has been newly established as a service part. The anti-corrosion surface treatment has been changed from Zn to Zn-Ni plating. |
| 05-002-17-3355 | 2017-10-21. Service bulletin. POWER TRAIN. Some vehicles may exhibit one of the following concerns: Sometimes the shifter may jump out of 3rd gear over a road bump when accelerating after deceleration at 25-40 mph (40-65 km/h) Hard to shift into 3rd, 4th, 5th, and/or 6th gear Shift lever vibrates when driving in 3rd or 4th gear. This is caused by inappropriate transmission internal parts. |
| 09-021-17-3356 | 2017-10-21. Service bulletin. EQUIPMENT:MECHANICAL. Some vehicles may experience a rattle noise from the front door glass when driving with the window open approx. 1/2 to 4 inches (1 - 10 cm). The rattle noise may be caused by insufficient holding force of the glass run channel. To increase the holding force, the shape of glass run channel has been changed and non-woven pads have been attached to the glass run channel. |
| 09-017-17-3347a | 2017-10-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502or later).NOTE:For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tabin MAZDA CONNECT Settingsbefore performing the update. |
| 06-001-17-3307a | 2017-10-21. Service bulletin. STEERING: STEERING WHEEL/HANDLE BAR. Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance.This concern may be caused by an insufficient wear resistance of the steering wheel surface. |
| 01-005-17-3305a | 2017-10-21. Service bulletin. EQUIPMENT:MECHANICAL. Some vehicles may exhibit oil residue on the engine front cover from seepage around the joint portion (A) between the cylinder block and head. It becomes very noticable with dust adhesion. In some cases, the area of oil residue extends down to around the joint portion (B) between the engine front cover and the oil pan. This may be caused by oil escaping from a fine clearance created at the sealant applied to joint (A) between the cylinder block (B) and head (C) when the engine was pressurized during leak testing on the engine assembly line. |
| SA-036-17 | 2017-10-12. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL. IDS SOFTWARE VERSION 107 AVAILABLE ON MGSS - PLEASE UPDATE YOUR PC'S. Upgrade your PCs to IDS version 107.00 and 107.01 from the previous version. |
| SA-066-17 | 2017-10-12. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS:HIGH/LOW BEAM DIMMER SWITCH; FORWARD COLLISION AVOIDANCE: SENSING SYSTEM. Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern. NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details. |
| SA-065-17 | 2017-10-04. Service bulletin. EQUIPMENT:ELECTRICAL. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. MAZDA CONNECT Symptom Troubleshooting Table Sections: Audio System, Bluetooth®, Center Display, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux, Voice Command |
| 01-011-17-3364a | 2017-10-04. Service bulletin. ENGINE. If a customer brings their vehicles in with DTC P2183:00 stored, repair the vehicle using the following Repair Procedure and Caution. P2183:00: ECT sensor No.2 circuit range/performance problem. This is caused by the ECT sensor No.2 located near the bottom of the radiator getting wet and water entering the part due to insufficient water resistance. To correct this issue, the water resistance of the ECT sensor No.2 has been improved. |
| 01-012-17-3382 | 2017-10-04. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. This service information provides basic Q-85/T-110 battery handling procedures. Complete service information can be found in MGSS online or Workshop Manual (section 13-17). |
| 09-017-17-3347c | 2017-10-04. Service bulletin. ELECTRICAL SYSTEM. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update. |
| 06-002-17-3367 | 2017-10-04. Service bulletin. SUSPENSION; STEERING. Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is turned to the full left position. NOTE: The noise will not occur if the steering wheel is in the center or full right position. The noise is caused when the edge (A) of the left side inner ball joint (B) gets stuck with the steering gear housing (C). |
| 04-002-17-3316b | 2017-10-04. Service bulletin. SERVICE BRAKES, HYDRAULIC. Some vehicles may exhibit a squeak noise when applying the brakes and/or groove marks (A) on the front disc plates. This is caused by abrasive metal from the front disc plate sticking to the brake pad, which damages the disc plate over time. To correct the problem, a modified brake pad is being used. |
| 09-001-17-3296b | 2017-10-04. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS; STRUCTURE; ELECTRICAL SYSTEM. When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. In most cases you will find that the Bulb Seal No. 1 (A) or HID Bulb Seal No. 1 (B) and Bulb Seal No. 2 (C) socket covers have not been correctly installed or are missing due to improper prior repairs (i.e., customer replacing the headlamp bulbs or body shop not transferring them when replacing the headlamp unit(s) due to a collision). Any damage caused by missing socket covers, HID module seal (D), or missing bumper brackets (E) is not covered by warranty policy. |
| 09-035-17-3080 | 2017-10-04. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer?s responsibility to comply with Federal, State, and local laws concerning odometerand related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the ?SpeedometerReplacement Label?.Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda?s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service.With the use of SPECMO?s services, a Mazda dealer can get the odometer setting updated to reflect the correct mileage at the time of replacement for both warranty and customer pay repairs, therefore resulting in a higher level of customer satisfaction. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.