WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Mazda Mazda3

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

882 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
01-001-15-29882017-05-25. Service bulletin. ENGINE. SOME VEHICLES EQUIPPED WITH SKYACTIV-G 2.0L ENGINE MAY EXPERIENCE ENGINE OIL SEEPAGE FROM DRAIN PLUG AFTER THE ENGINE OIL IS REPLACED EVEN IF THE PLUG IS TIGHTENED TO THE SPECIFIED TORQUE WITH A NEW GASKET. OIL PAN DRAIN PLUG TIGHTENING TORQUE: 30—41 N·M {3.1—4.1 KGF·M, 23—30 FT·LBF} SEATING SURFACE OF THE OIL PAN FOR THE DRAIN PLUG MAY HAVE POOR FLATNESS DUE TO IMPROPER SPOT WELDING AND/OR THE SURFACE MAY HAVE GOTTEN A SCRATCH DURING MANUFACTURING PROCESS.
09-001-15-29792017-05-25. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. SOME CUSTOMERS MAY COMPLAIN ABOUT THE MAZDA CONNECT CLOCK (IN THE CENTER DISPLAY) CHANGING ON ITS OWN AND DISPLAYING THE TIME OF THE NEXT TIME ZONE (ONE HOUR SHIFTED FROM THE ACTUAL). THIS OCCURS WHEN THE GPS SYNC IS SET ON IN THE CLOCK SETTINGS AND THE VEHICLE IS USED WHERE TWO DIFFERENT TIME ZONES EXIST. THIS CONCERN IS CAUSED BY A WRITING ERROR OF THE TIME ZONES IN THE SD CARD SOFTWARE (MAP DATA). THE SD CARD SOFTWARE HAS BEEN UPDATED TO ELIMINATE THIS CONCERN.
09-002-15-29952017-05-25. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. SOME VEHICLES MAY EXHIBIT POOR RECEPTION OF THE FM RADIO WHERE THE RECEPTION CUTS IN AND OUT ERRATICALLY AND/OR THE SOUND VOLUME VARIES BY ITSELF. THIS CONCERN MAY BE CAUSED BY INADEQUATE SOFTWARE OF THE TUNER AND AMP UNIT (TAU) OR THE AUDIO UNIT. THE SOFTWARE OF THE TAU AND THE AUDIO UNIT HAS BEEN RE-TUNED FOR OPTIMUM FM RADIO RECEPTION.
09-003-15-29972017-05-25. Service bulletin. STRUCTURE:BODY:ROOF AND PILLARS. SOME VEHICLES MAY EXHIBIT A NOISE FROM THE BOTTOM OF THE A-PILLAR WHEN DRIVING ON ROUGH ROADS OR OVER BUMPS. THIS IS CAUSED BY THE COWL UPPER PLATE AND/OR DASH UPPER PANEL INTERFERING WITH THE WIPER BRACKET. FOR THE AFFECTED VEHICLES, A CLEARANCE NEEDS TO BE CREATED BETWEEN THE WIPER BRACKET AND COWL UPPER PLATE AND BETWEEN THE WIPER BRACKET AND DASH UPPER PANEL. TO CORRECT THE CONCERN, ADDITIONAL SEALING AND WELDING HAVE BEEN APPLIED TO THE WIPER BRACKET.
02-001-15-29982017-05-25. Service bulletin. STRUCTURE:FRAME AND MEMBERS. SOME VEHICLES MAY EXHIBIT A CREAKING NOISE FROM UNDER THE FRONT OF THE VEHICLE WHEN DRIVING OVER BUMPS. THE NOISE OCCURS AT APPROX. 12 - 25 MPH (20 - 40 KM/H) WHEN THE ROAD SURFACE IS WET OR AFTER A CAR WASH. THE NOISE BECOMES MORE NOTICEABLE WHEN DRIVING OVER HIGHER BUMPS. THE CREAKING NOISE IS CAUSED WHEN THE FRONT LOWER CONTROL ARM BUSHING(S) (A) BECOME WET.
07-002-15-30042017-05-25. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. SOME CUSTOMERS MAY COMPLAIN ABOUT NO COOL AIR FROM THE VENTS WHEN THE AIR CONDITIONER (A/C) IS ON. THIS CONCERN MAY BE CAUSED BY A/C REFRIGERANT LEAKING FROM THE EVAPORATOR. SOME DEFORMED EVAPORATOR TUBES SLIPPED THROUGH QUALITY INSPECTION AND WERE USED DURING PRODUCTION. A/C REFRIGERANT LEAKS FROM IMPROPER BRAZING AT A JOINT. TO CORRECT THE PROBLEM, THE PRODUCTION AND INSPECTION CONTROL OF THE EVAPORATOR HAVE BEEN IMPROVED.
07-003-15-29922017-05-25. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. SOME CUSTOMERS MAY COMPLAIN ABOUT THAT AIR TEMPERATURE FROM THE AIR CONDITIONER WILL NOT CHANGE BY THE AIR TEMPERATURE CONTROL KNOB, AND MAY BE ACCOMPANIED BY SOME RATTLE NOISE FROM INSIDE OF THE DASH BOARD. THIS CONCERN MAY BE CAUSED BY THE TEMPERATURE CONTROL LINK BEING PULLED OUT OF THE HVAC HOUSING. TO CORRECT THE PROBLEM, THE TEMPERATURE CONTROL LINK HAS BEEN MODIFIED.
01-002-15-30052017-05-25. Service bulletin. FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP. SOME VEHICLES MAY EXHIBIT A TAPPING NOISE COMING FROM INSIDE THE FUEL TANK (UNDER THE REAR SEAT) WHEN IDLING AFTER THE FUEL TANK HAS BEEN FILLED UP. THE NOISE DISAPPEARS AFTER DRIVING AND CONSUMING SOME FUEL. THE CONCERN WILL LIKELY OCCUR IF THE FUEL TANK IS OVERFILLED (MORE FUEL IS ADDED AFTER THE FUEL PUMP NOZZLE SHUTS OFF AUTOMATICALLY) OR FILLED UP NORMALLY IN HIGH AMBIENT TEMPERATURES AND THE FUEL EXPANDS. THIS NOISE IS CAUSED WHEN THE FLOAT INSIDE THE ROLL OVER VALVE (ROV) MOVES UP AND DOWN WHEN THE TANK IS OVERFILLED. TO CORRECT THE PROBLEM, THE ROV HAS BEEN MODIFIED TO RESTRICT THE UP AND DOWN MOVEMENT OF THE FLOAT.
09-007-15-30112017-05-25. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. SOME VEHICLES MAY HAVE THE BLIND SPOT MONITORING (BSM) OFF INDICATOR LIGHT FLASHING AND DTC U3000:54 STORED IN MEMORY. THE CONCERN IS CAUSED BY INADEQUATE BSM CONTROL MODULE CONTROL LOGIC. THE BSM CONTROL MODULE SOFTWARE HAS BEEN UPDATED TO ELIMINATE THIS CONCERN.
09-001-15-2979A2017-05-25. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. SOME CUSTOMERS MAY COMPLAIN ABOUT THE MAZDA CONNECT CLOCK (IN THE CENTER DISPLAY) CHANGING ON ITS OWN AND DISPLAYING THE TIME OF THE NEXT TIME ZONE (ONE HOUR SHIFTED FROM THE ACTUAL). THIS OCCURS WHEN THE GPS SYNC IS SET ON IN THE CLOCK SETTINGS AND THE VEHICLE IS USED WHERE TWO DIFFERENT TIME ZONES EXIST. THIS CONCERN IS CAUSED BY A WRITING ERROR OF THE TIME ZONES IN THE SD CARD SOFTWARE (MAP DATA). THE SD CARD SOFTWARE HAS BEEN UPDATED TO ELIMINATE THIS CONCERN.
01-003-15-30142017-05-25. Service bulletin. EQUIPMENT. USE THE FOLLOWING REPAIR PROCEDURE TO MINIMIZE THE NEED TO REPLACE THE CATALYST CONVERTER/EXHAUST PIPE WHEN REMOVING OXYGEN SENSORS AND/OR AIR FUEL RATIO SENSORS.
09-009-15-30152017-05-25. Service bulletin. EQUIPMENT. SOME VEHICLES MAY EXPERIENCE STAINS APPEARING ON THE HOOD, ROOF AND/OR TRUNK OF THE VEHICLE. THIS CONCERN IS MOST LIKELY TO BE FOUND IN A COLD WEATHER AREAS JUST AFTER THE RAPGARD IS REMOVED AT PDI. THIS MAY BE CAUSED BY MOISTURE WHICH HAS BEEN TRAPPED AND CONDENSED BETWEEN THE PAINT AND THE RAPGARD. THESE TYPES OF STAINS CAN BE REMOVED WITH A HEAT GUN OR AN INFRARED DRIER. IF YOU ENCOUNTER THIS CONCERN DURING PDI, USE A HEAT GUN OR AN INFRARED DRIER TO APPLY HEAT TO THE AFFECTED AREA TO REMOVE THE STAIN(S).
05-004-15-30342017-05-19. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME CUSTOMERS MAY COMPLAIN OF A CHECK ENGINE LIGHT AND A/T WARNING LIGHT ON WHEN STARTING THE ENGINE. AT THE SAME TIME, AN ENGINE INSPECTION REQUIRED MESSAGE IS DISPLAYED ON THE LCD. DTC P0722:00 IS STORED IN THE TRANSMISSION CONTROL MODULE (TCM) MEMORY. • DTC P0722:00 (OPEN CIRCUIT IN OUTPUT SPEED SHAFT CIRCUIT) THE TCM CONTROL LOGIC HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.
05-005-15-30272017-05-19. Service bulletin. EQUIPMENT. SOME CUSTOMERS MAY COMPLAIN OF A WHINING NOISE FROM THE AUTOMATIC TRANSAXLE WHEN DRIVING AT 10 MPH AND ABOVE. THE NOISE: • DEPENDS ON THE VEHICLE’S SPEED ONLY (THE MORE SPEED, THE MORE NOISE) • OCCURS WITH ALL TYPES OF DRIVING (ACCELERATION, DECELERATION, STEADY SPEED) • DOES NOT DEPEND ON RPM, GEAR, OR ATF TEMPERATURE THIS IS CAUSED BY A DAMAGED BEARING IN THE TRANSAXLE DUE TO IMPROPER CONFIGURATION OF THE TRANSAXLE CASE. A MODIFICATION HAS NOW BEEN IMPLEMENTED ON AUTOMATIC TRANSAXLES WITH THE SERIAL NUMBER 3TR1111680 AND HIGHER OR 3TD1104906 AND HIGHER. THE SERIAL NUMBER CAN BE FOUND ON TOP OF THE TRANSAXLE CASE NEAR THE MANUAL SHAFT LEVER.
01-004-15-30282017-05-19. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0191:00 OR DTC P0088:00 STORED IN MEMORY. DTC P0191:00: FUEL PRESSURE SENSOR CIRCUIT RANGE/PERFORMANCE PROBLEM (EXCEPT 2014 MAZDA3) DTC P0088:00: FUEL PRESSURE SENSOR CIRCUIT RANGE/PERFORMANCE PROBLEM (2014 MAZDA3) THIS IS CAUSED BY THE HIGH PRESSURE FUEL PUMP NOT GENERATING THE TARGET FUEL PRESSURE (DUE TO A MANUFACTURING ERROR OF THE INNER PARTS). TO CORRECT THE PROBLEM, PRODUCTION CONTROL HAS BEEN IMPROVED.
09-011-15-30322017-05-19. Service bulletin. EQUIPMENT. SOME VEHICLES MAY EXPERIENCE A POPPING NOISE COMING FROM THE SPEAKER(S) WHEN OPERATING THE POWER WINDOW MASTER SWITCHES AT THE DRIVER’S DOOR. THIS IS CAUSED BY INSUFFICIENT NOISE SUPRESSION IN THE TUNER AMP UNIT (TAU). TO CORRECT THE PROBLEM, THE INTERNAL NOISE SUPRESSOR IN THE TAU HAS BEEN CHANGED
09-012-15-30352017-05-19. Service bulletin. LATCHES/LOCKS/LINKAGES. SOME VEHICLES MAY EXHIBIT THE REAR CONSOLE LID (A) NOT BEING ABLE TO LATCH DUE TO A BROKEN LATCH (B). THE LATCH MAY BE BROKEN BY EXCESSIVE EXTERNAL FORCE APPLIED TO THE LID. TO CORRECT THE PROBLEM, THE REAR CONSOLE LID LATCH HAS BEEN CHANGED TO INCREASE THE STRENGTH.
09-014-15-30372017-05-19. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. SOME VEHICLES MAY EXHIBIT CORROSION AROUND THE SPOT WELDS IN THE TRUNK OPENING UNDER THE REAR WINDOW. THIS IS CAUSED BY INSUFFICIENT PAINT THICKNESS AT THE SPOT WELDS. TO CORRECT THE PROBLEM, THE PAINT THICKNESS HAS BEEN IMPROVED
02-004-15-30132017-05-19. Service bulletin. SUSPENSION:FRONT:SHOCK ABSORBER. SOME VEHICLES MAY EXHIBIT ONE OR BOTH OF THE FOLLOWING NOISES FROM THE FRONT SHOCK ABSORBER. • A POPPING NOISE WHEN PASSING OVER SPEED BUMPS. • A SQUEAKING NOISE WHEN URNING THE STEERING WHEEL AT A VEHICLE STANDSTILL. TO CORRECT THE PROBLEM, THE SHAPE OF THE BUMP STOPPER HAS BEEN MODIFIED AND A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING.
05-002-15-3019C2017-05-19. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
09-050-14-29652017-05-19. Service bulletin. VISIBILITY/WIPER. SOME VEHICLES MAY EXHIBIT A SQUEAKING NOISE FROM THE WINDSHIELD WIPER LINK WHEN OPERATING THE WIPERS. THIS NOISE MAY BE CAUSED BY RUST ON THE SLIDING PARTS FROM WATER ENTRY THROUGH THE PIVOT (A). TO PREVENT WATER ENTRY, THE PIVOT COVER (B) HAS BEEN ENLARGED AND AN O-RING HAS BEEN ADDED TO THE PIVOT.
02-005-14-29812017-05-19. Service bulletin. EQUIPMENT. SOME VEHICLES MAY EXHIBIT A CREAKING NOISE FROM UNDER THE FRONT OF THE VEHICLE WHEN DRIVING OVER BUMPS. THE NOISE OCCURS AT APPROX. 12 - 25 MPH (20 - 40 KM/H) WHEN THE ROAD SURFACE IS WET OR AFTER A CAR WASH. THE NOISE BECOMES MORE NOTICEABLE WHEN DRIVING OVER HIGHER BUMPS. THE CREAKING NOISE IS CAUSED WHEN THE FRONT LOWER CONTROL ARM BUSHING(S) (A) BECOME WET.
00-004-14-29832017-05-19. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. IN SUPPORT OF THE SKYACTIV MODELS, MAZDA WILL MAKE AVAILABLE A SPECIAL SERVICE TOOL (SST), TO ADDRESS FRONT SUSPENSION NOISE FOR SPECIFIC HIGH HUMIDITY AND WET CLIMATE CONDITIONS IN THE LOWER GULF STATES. THE SST WILL BE NEEDED TO COMPLETE REPAIRS DETAILED IN TSB 02-005/14 AND IS AVAILABLE THROUGH MAZDA’S TOOL VENDOR, SNAP-ON TOOLS.
09-051-14-29862017-05-19. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. SOME VEHICLES MAY EXHIBIT A WHISTLE NOISE FROM THE OUTER MIRROR WHILE DRIVING AT 37 MPH (60 KM/H) OR MORE. THIS NOISE MAY BE CAUSED BY AIR PASSING THROUGH A GAP IN THE MIRROR BASE COVER. TO CORRECT THE PROBLEM, THE SHAPE OF THE MIRROR BASE COVER HAS BEEN CHANGED.
08-001-15-30172017-05-18. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXHIBIT INSTRUMENT CLUSTER TPMS, ABS AND TCS/DSC INDICATOR WARNING LIGHTS ON AND DTC U3000:49[STANDARD DEPLOYMENT CONTROL SYSTEM] OR C0061:29, C0062:29, C0063:29 [STANDARD DEPLOYMENT CONTROL SYSTEM] STORED IN MEMORY. THE AIRBAG, SCBS, AT, MRCC, LDWS AND HBC INSTRUMENT CLUSTER INDICATOR LIGHTS MAY ALSO COME ON. INTERNAL FAILURE OF THE SAS CONTROL MODULE MAY BE THE CAUSE.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.