WenmarOpen by Wenmar Pro

Service bulletins for the 2018 Mazda Mazda2

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

108 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
01-005-21-37782021-03-03. Service bulletin. ELECTRICAL SYSTEM. The Mazda DCA-8000PM is required for all warranty battery testing. If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
09-002-21-37702021-02-05. Service bulletin. ELECTRICAL SYSTEM; VEHICLE SPEED CONTROL; EQUIPMENT. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer
SA2662021-02-01. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. MAZDA Mobile start (MMS) cannot communicate with vehicle
MT-006-202020-12-03. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. Some customers may complain about the following MAZDA CONNECT™ Temperature Warning message: • Display is too Hot. Screen performance may be decreased until it cools. The warning message displays when the MAZDA CONNECT™ screen temperature is above 176 degrees Fahrenheit (80 degrees Celsius).
MT-005-202020-12-03. Service bulletin. ENGINE AND ENGINE COOLING. Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Engine Oil Consumption Inspection Guideline 1. Record the vehicle mileage. 2. Engine at normal operating temperature, top off engine oil level to the full mark on the dipstick. 3. Ask the customer to return to the dealer after 1200 miles to recheck the engine oil level. 4. After 1200 miles, engine at normal operating temperature, check the engine oil level on the dipstick. 5. Is the engine oil level above the low mark on the dipstick? • Yes - No repair is necessary. • No - Proceed to MGSS online or Workshop Manual (section 01-03 NO. 16 HIGH OIL CONSUMPTION/LEAKAGE).
07-004-20-37412020-10-03. Service bulletin. EQUIPMENT. Some customers may complain that the air conditioner (A/C) is not cooling. This may be caused by a refrigerant leak from the condenser due to corrosion where an anti-corrosion coating was uneven.
09-006-20-3673a2020-08-04. Service bulletin. EQUIPMENT. When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
02-005-20-36882020-08-04. Service bulletin. SUSPENSION; EQUIPMENT. Some customers may complain about a knocking noise heard from the rear suspension while driving on rough road. The noise may be caused by a broken bound (bump) stopper that breaks because of deterioration from environmental factors and bad road conditions. To eliminate this concern, a dust boot has been added in order to protect the bound (bump) stopper from water and the mounting rubber has been changed accordingly.
04-006-20-37072020-06-02. Service bulletin. SERVICE BRAKES, HYDRAULIC; STEERING. Some customers may experience a TCS/DSC warning light and SCBS warning light (amber) illumination with DTC C0051:62 stored in PCM memory. DTC C0051:62 - EPS control module[when the vehicle is driven in a straight line, the difference between the steering angle (calculated by each sensor) and the steering angle (from the steering angle sensor) is greater than the specification]. This concern most likely occurs during the following situations: When the vehicle is turning in reverse, right after starting the engine. When the vehicle is going over a bump or a curb, right after starting the engine. This concern may be caused when the DSC HU/CM performs the steering center position calibration. During the learning process, if a shock is applied to the vehicle by a bump or curb etc., the steering center position may not be properly detected and creates a steering center position error. To eliminate this concern, the DSC HU/CM control software has been modified
09-003-20-36712020-01-23. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer’s responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. • Mazda vehicles are manufactured with tamper-proof speedometers. • When a speedometer is replaced, the new speedometer will read zero (0) miles. • This procedure is extremely important to accurately represent actual vehicle mileage. • Prior to speedometer removal, complete the information required on the “Speedometer Replacement Label”. Labels can only be ordered through Mazda eStore. • In an effort to achieve a higher level of Customer Experience and retain the value of Mazda’s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO’s services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
MT-002-192019-12-20. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT. If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.
MT-003-192019-10-30. Service bulletin. ENGINE AND ENGINE COOLING. Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary:
MT-002-192019-10-04. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.
09-031-19-36252019-08-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. After the installation of a new instrument cluster, the message "Fctry" or “Factory” is displayed instead of the odometer. This concern may also occur when a room fuse is installed in a new vehicle. Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required. NOTE: The concern is applicable to Calsonic Kansei instrument clusters. Not all trim levels are affected.
09-010-19-36242019-08-15. Service bulletin. VISIBILITY; SERVICE BRAKES, HYDRAULIC; EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. Customers concern can be resolved by sanding off paint at ground point (3) where attachment bolt (4) is seated. After installing the bolt (4), apply touch-up paint to the exposed base material area of the front fender stay.
SA-016-192019-04-25. Service bulletin. WHEELS; SUSPENSION:FRONT:WHEEL BEARING. There have been warranty claims submitted for noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
09-010-19-35772019-03-11. Service bulletin. ELECTRICAL SYSTEM. Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.
MT-012-182019-03-04. Service bulletin. STRUCTURE:BODY; STEERING. If a vehicle has body vibration or steering wheel shimmy while driving and the root cause is determined to be tire balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. If your dealer does not have a GSP9700 or equivalent balance machine, sublet the vehicle out for repair. To find the location of a GSP9700 near your dealer, visit Hunter?s web site at www.gsp9700.com and click on ?Locate a GSP9700 Road Force Balancer.?
02-003-19-35472019-02-19. Service bulletin. SUSPENSION. Beginning with the CX-5, grip type front and rear stabilizer bushings have been incorporated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.
09-035-18-35092018-10-09. Service bulletin. ELECTRICAL SYSTEM. Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.
09-033-18-35062018-09-10. Service bulletin. ELECTRICAL SYSTEM. Some customers may experience the active driving display (auto flip-up type) does not flip up and no DTC is stored. Due to improper assembly, a deformed bracket may cause a loose mesh between internal gears. To correct this issue, the active driving display has been changed.
MT-001-182018-04-23. Service bulletin. EQUIPMENT:ELECTRICAL. When installing a navigation SD card, the center display may show error message "Invalid SD Card".
02-005-18-34442018-04-23. Service bulletin. SUSPENSION. Beginning with the CX-5, grip type front and rear stabilizer bushings have been incorporated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.
09-002-18-34102018-03-05. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. After the installation of a new instrument cluster, the message "Fctry" or "Factory" is displayed instead ofthe odometer. This concern may also occur when a room fuse is installed in a new vehicle.Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required.NOTE: The concern is applicable to Calsonic Kansei instrument clusters. Not all trim levels are affected.CX-3 shown:Vehicles having this concern should have their vehicle repaired using the following procedure.
MT-001-182018-02-26. Service bulletin. ELECTRICAL SYSTEM. When installing a navigation SD card, the center display may show error message "Invalid SD Card". This may be caused by: The navigation SD card lock tab is locked.The navigation SD card has a VIN mismatch due to SD card swapping.The navigation SD card has a malfunction.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.