Service bulletins for the 2018 Mazda CX-9
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
470 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| SA-032-23 | 2023-06-04. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. |
|---|---|
| SA-031-23 | 2023-06-04. Service bulletin. WHEELS. Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration. |
| 05-002-23 | 2023-06-04. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). |
| 01-007-23 | 2023-06-04. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY; ELECTRICAL SYSTEM. The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. |
| 09-013-23a | 2023-05-03. Service bulletin. ELECTRICAL SYSTEM. Some customers may experience electrical devices that cannot be charged through the rear console or the trunk side trim USB power outlet. This may be caused by an excessive external force applied to the USB power outlet. To eliminate this concern, the soldering strength of the USB port has been enhanced. |
| 06-001-23a | 2023-05-03. Service bulletin. STEERING. Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. |
| SA-012-23 | 2023-04-04. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM; VISIBILITY. Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet. |
| SA-016-23 | 2023-04-04. Service bulletin. EQUIPMENT:ELECTRICAL. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method. B. Auxiliary Key Code Cut Method |
| SA-007-23 | 2023-03-03. Service bulletin. POWER TRAIN. The rear differential case could develop a crack in the case. NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles. This concern is caused when the sliding bearing (1) in the coupling (2) is seized and causes the coupling component to fit loosely. The pinion shaft head (3) then contacts the differential case and causes a crack. |
| 07-002-23 | 2023-03-03. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 °F (10°C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced since December 2021 at the supplier. |
| 09-016-23 | 2023-03-03. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER. Speedometer replacement procedure |
| 09-013-23 | 2023-03-03. Service bulletin. ELECTRICAL SYSTEM. Some customers may experience electrical devices that cannot be charged through the rear console or the trunk side trim USB power outlet. This may be caused by an excessive external force applied to the USB power outlet. To eliminate this concern, the soldering strength of the USB port has been enhanced. |
| 01-002-23a | 2023-03-03. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold flange (2) on the cylinder head. |
| 01-001-23a | 2023-03-03. Service bulletin. ENGINE AND ENGINE COOLING. Some customers may complain about a poor acceleration and rough idling or the CHECK ENGINE light ON with DTC P0301:00, P0302:00, P0303:00, P0304:00.NOTE: Only turbo engines are applicable; non-turbo engines are NOT applicable. In most cases, DTCs P030X stores, but sometimes not. Sometimes the CHECK ENGINE light does not recognize this engine concern. This is caused by the variable valve in the exhaust manifold seizing and causing the exhaust port to become hot and the exhaust valve seat to wear unevenly, resulting in compression leakage. To eliminate this concern, the design of the exhaust manifold has been modified. |
| 09-006-23 | 2023-02-02. Service bulletin. STRUCTURE. When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). |
| 01-002-23 | 2023-02-02. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING. Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole or at the outside of the exhaust manifold. Cracks may be caused by: - Deformation of the exhaust manifold during usage causing unexpected force to certain areas of the cylinder head. - Residual stress generated during production in the cylinder head material may be greater than expected. The external force from the exhaust system when driving over bumps may cause unexpected force to certain areas of the cylinder head. To eliminate this concern, the design of the exhaust manifold gasket and the cylinder head has been modified to reduce the force on the cylinder head. |
| 01-001-23 | 2023-02-02. Service bulletin. ENGINE AND ENGINE COOLING. Some customers may complain about a poor acceleration and rough idling or the CHECK ENGINE light ON with DTC P030X:00 (only turbo engines are applicable; non-turbo engines are NOT applicable). - In most cases, P030X is stored, but sometimes not. - Sometimes the CHECK ENGINE light does not recognize this engine concern. This is caused by the variable valve in the exhaust manifold seizing and causing the exhaust port to become hot and the exhaust valve seat to wear unevenly, resulting in compression leakage. To eliminate this concern, the design of the exhaust manifold has been modified. |
| SA-007/23 | 2023-02-02. Service bulletin. POWER TRAIN. The rear differential case could develop a crack in the case NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles. This concern is caused when the sliding bearing in the coupling is seized and causes the coupling component to fit loosely. The pinion shaft head then contacts the differential case and causes a crack. |
| SA-003/23 | 2023-02-02. Service bulletin. SERVICE BRAKES. Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern. |
| RF-23-01 | 2023-02-02. Service bulletin. ENGINE AND ENGINE COOLING. When servicing SKYACTIV engine vehicles requiring to replace the Oil Galley Plug and Crush Washer, order the required part numbers below. These parts are not listed in GEPC and were previously listed as "non-serviceable" in the cylinder block diagram. |
| 04-005-22 | 2023-01-05. Service bulletin. SERVICE BRAKES, HYDRAULIC. Front Brake Noise Symptom 1: Some vehicles may exhibit a click noise when first moving forward or reverse from a stop OR when first applying the brakes while moving forward at slow speeds. This is caused by deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise. Front Brake Noise Symptom 2: Some vehicles may exhibit the brakes having an unusual noise or vibration when applying the brake. This is caused by rust on the brake disc plate’s surface. Rear Brake Noise Symptom 1: Some vehicles may exhibit grooves in rear brake disc plate(s). This concern is mostly found on new or low mileage vehicles, when the brakes are new. The grooves may be caused through abrasion from the accumulation of metal particles from the rear brake disc plates. The metal particles get caught between the brake pads and disc plates causing groove damage. To eliminate this concern, the disc plate surface honing process has been changed to reduce metal particle formation. Rear Brake Noise Symptom 2: Some vehicles equipped with an electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. This is caused by rust on the brake disc plate’s surface. NOTE: The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise. |
| SA-078-22 | 2023-01-05. Service bulletin. SERVICE BRAKES, HYDRAULIC. Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern. |
| SA-016-22a | 2023-01-05. Service bulletin. EQUIPMENT. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method |
| MT-004-22 | 2023-01-05. Service bulletin. ENGINE AND ENGINE COOLING. Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure. |
| SA-075-22 | 2022-12-02. Service bulletin. ELECTRICAL SYSTEM. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Cell phone charger/accessory in 12V socket (engine no start or unable to turn off) 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.