WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Mazda CX-9

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

513 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Body and frame are shown. Show all

Bulletins, newest first
09-012-19-35352019-03-20. Service bulletin. LATCHES/LOCKS/LINKAGES; STRUCTURE:BODY:HATCHBACK/LIFTGATE. While stopped with the transmission in Park position, some vehicles may exhibit concerns that the liftgate unlatches itself without pressing the liftgate opener switch (1) or it will not unlatch when pressing the liftgate opener switch (1). NOTE: The liftgate (power or manual type) will not unlatch or open by itself while the vehicle is being driven. This concern can only occur while the vehicle is stopped and in the Park position. This concern may be caused by water entry into the liftgate, through the garnish mounting area or outer panel. Condensation water may enter into the liftgate and drip onto the liftgate opener switch causing corrosion. The corrosion may create a poor contact or short in the liftgate opener switch. To eliminate this concern in the future, the structure of the liftgate opener switch has been improved.
MT-012-182019-03-04. Service bulletin. STRUCTURE:BODY; STEERING. If a vehicle has body vibration or steering wheel shimmy while driving and the root cause is determined to be tire balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. If your dealer does not have a GSP9700 or equivalent balance machine, sublet the vehicle out for repair. To find the location of a GSP9700 near your dealer, visit Hunter?s web site at www.gsp9700.com and click on ?Locate a GSP9700 Road Force Balancer.?
09-008-19-35652019-02-19. Service bulletin. STRUCTURE. Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).
09-042-18-35362018-12-17. Service bulletin. STRUCTURE:BODY:BUMPERS. Some customers may notice cracks at one or both ends of the front bumper near the front fender / front combination light. This may be caused when driving over bumps. The bumper fascia may receive higher than expected forces, depending on driving manner and road conditions. To eliminate this concern, the internal shape and material of the front bumper fascia has been modified.
09-021-18-3459a2018-11-13. Service bulletin. EQUIPMENT; STRUCTURE. Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may becaused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).
09-014-18-3443a2018-11-13. Service bulletin. EQUIPMENT; STRUCTURE. When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).
MT-006-182018-08-27. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE:BODY:HATCHBACK/LIFTGATE. POWER LIFTGATE INOPERATIVE WITH DTC U3003:16: Some customers may complain about an inoperative power liftgate (PLG) with DTC U3003:16 (Power liftgate (PLG) control module power supply voltage low input) is stored in memory. This may be caused by low vehicle battery voltage.
SA-024-182018-07-02. Service bulletin. STRUCTURE:BODY:HOOD. Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
09-021-18-34592018-05-14. Service bulletin. STRUCTURE:BODY:TRUNK LID; STRUCTURE:BODY:ROOF AND PILLARS; STRUCTURE:BODY:HOOD. Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).
09-014-18-34432018-04-23. Service bulletin. STRUCTURE. When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
09-004-18-3402a2018-03-05. Service bulletin. STRUCTURE:BODY:DOOR. Some customers may complain that the door weatherstrip (1) comes off at the front / lower part of the reardoor(s). This concern is caused by insufficient weatherstrip gripping force.
09-004-18-34022018-03-05. Service bulletin. STRUCTURE:BODY:DOOR. Some customers may complain that the door weatherstrip (1) comes off at the front / lower part of the reardoor(s). This concern is caused by insufficient weatherstrip gripping force.
09-023-17-33482017-10-21. Service bulletin. STRUCTURE:BODY:BUMPERS. On some vehicles, the front bumper cover may pop out causing a poor appearance complaint. This may be caused by an insufficient amount of holding force of the bumper slider.
09-001-17-3296b2017-10-04. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS; STRUCTURE; ELECTRICAL SYSTEM. When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. In most cases you will find that the Bulb Seal No. 1 (A) or HID Bulb Seal No. 1 (B) and Bulb Seal No. 2 (C) socket covers have not been correctly installed or are missing due to improper prior repairs (i.e., customer replacing the headlamp bulbs or body shop not transferring them when replacing the headlamp unit(s) due to a collision). Any damage caused by missing socket covers, HID module seal (D), or missing bumper brackets (E) is not covered by warranty policy.
09-023-17-3348a2017-10-04. Service bulletin. STRUCTURE:BODY:BUMPERS. On some vehicles, the front bumper cover may pop out causing a poor appearance complaint. This may be caused by an insufficient amount of holding force of the bumper slider. To eliminate this concern, the configuration of the bumper slider has been changed.
1098M2017-02-14. Service bulletin. STRUCTURE. WHEN REMOVING PARTS FROM A VEHICLE, TAKE CAUTION OF THIS SYMBOL "R". FAILING TO REPLACE THE NON-REUSABLE PART MAY CAUSE A SYSTEM FAILURE.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.