WenmarOpen by Wenmar Pro

Service bulletins for the 2016 Mazda CX-5

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

705 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
05-005-20-37522020-12-03. Service bulletin. POWER TRAIN. Some customers may complain of a whining noise from the automatic transaxle when driving at 10 mph and above. The noise: • Depends on the vehicle’s speed only (the more speed, the more noise) • Occurs with all types of driving (acceleration, deceleration, steady speed) • Does not depend on rpm, gear, or ATF temperature
05-004-20-37272020-08-04. Service bulletin. POWER TRAIN. Some vehicles may exhibit one of the following concerns: • Sometimes the shifter may jump out of 3rd gear over a road bump when accelerating after deceleration at 25-40 mph (40-65 km/h) • Hard to shift into 3rd, 4th, 5th, and/or 6th gear • Shift lever vibrates when driving in 3rd or 4th gear. This is caused by inappropriate transmission internal parts.
05-003-20-37252020-08-04. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; POWER TRAIN; EQUIPMENT; ENGINE. Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic.
SA-053-202020-07-03. Service bulletin. POWER TRAIN. When replacing manual or automatic transmission, make sure to remove the plug from the old transmission (as shown below) and then re-install it to the new transmission with a new washer. The new transmissions (including remanufactured A/T) have a shipping plug, as shown in the figures (M/T: black, rubber made; A/T: pink and black, with breather). This plug is for shipping use only and needs to be removed in order to re-install the original plug from the old transmission.
00-001-20-36892020-04-03. Service bulletin. SERVICE BRAKES, HYDRAULIC; POWER TRAIN; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE AND ENGINE COOLING. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
SA-030-202020-02-27. Service bulletin. POWER TRAIN. Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. NOTE: The following Caution is included with every ATX that requires configuration.
SA-058-192019-12-21. Service bulletin. POWER TRAIN; UNKNOWN OR OTHER. WARRANTY GUIDELINES FOR RETURNED TRANSMISSION CORES. Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the oil cooler was missing altogether. IMPORTANT NOTE: ALWAYS REMEMBER TO INCLUDE THE ORIGINAL OIL COOLER WITH THE RETURNED TRANSMISSION CORE!
SA-053-192019-12-21. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. GUIDE LINES AND PHOTOS TO DETERMINE IF FLUID/OIL SEEPAGE OR LEAK IS SEVERE ENOUGH TO REQUIRE WARRANTY REPAIR OR TO CLEAN AND MONITOR. Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
05-005-19-35692019-07-01. Service bulletin. POWER TRAIN. Some vehicles may exhibit one of the following concerns: Sometimes the shifter may jump out of 3rd gear over a road bump when accelerating after deceleration at 25-40 mph (40-65 km/h), Hard to shift into 3rd, 4th, 5th, and/or 6th gear, Shift lever vibrates when driving in 3rd or 4th gear. This is caused by inappropriate transmission internal parts.
05-004-19-34662019-05-30. Service bulletin. POWER TRAIN. Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on P0877:00 - Oil pressure switch No. 4 (oil pressure switch B) stuck on P0780:00 - Gear shifting malfunction P1738:00 - Automatic transaxle internal malfunction This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to the instructions on MGSS (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [FW6A-EL/FW6AX-EL]) or (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [EW6A-EL/EW6AX-EL]) for proper diagnosis and repair procedure.
01-008-19-3568a2019-04-25. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some customer using “Flexible” setting for Oil Change in the maintenance monitor may notice that the oil change due notification will not work due to improper control logic of the PCM. The PCM clears the TRAVELED DISTANCE at the wrong time while the ELAPSED DAYS and the DETERIORATION DETERMINATION work as designed. To correct this issue, the control logic of the PCM has been changed.
05-002-19-35762019-03-29. Service bulletin. POWER TRAIN; POWER TRAIN:AXLE ASSEMBLY. Some customers may complain of a whining noise from the automatic transaxle when driving at 10 mph and above. The noise: •Depends on the vehicle’s speed only (the more speed, the more noise)•Occurs with all types of driving (acceleration, deceleration, steady speed)•Does not depend on rpm, gear, or ATF temperature.This is caused by a damaged bearing in the transaxle due to improper configuration of the transaxle case. A modification has now been implemented on automatic transaxles with the following serial numbers: •7TN0820364 and higher (CX-3) / 8TN1090104 and higher (except CX-3) •8TR1008883 and higher •8TD1003276 and higher •8T50331192 and higher (CX-3) / 8T50329705 and higher (except CX-3).
03-001-19-3505b2019-03-29. Service bulletin. POWER TRAIN:DRIVELINE:DRIVESHAFT. Some vehicles may exhibit a squeak noise from the right front driveshaft at the automatic transaxle when driving. This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. The noise is caused by stick/slip between the oil seal at the transaxle and the dust cover of the driveshaft. To correct this issue, the thickness of the dust cover has been increased.
01-010-19-35822019-03-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE. Some vehicles may experience a lack of power and the check engine light on with DTC P61B:00 stored in the PCM memory when driving in high temperatures at high elevations. DTC P061B:00 - [PCM] Internal control module torque calculation performance problem.This concern may be caused by improper PCM control logic. The engine torque calculation error may increase in high temperatures at high elevations. To eliminate this concern, the PCM software has been modified.
01-008-19-35682019-03-11. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some customer using "Flexible" setting for Oil Change in the maintenance monitor may notice that the oil change due notification will not work due to improper control logic of the PCM. The PCM clears the TRAVELED DISTANCE at the wrong time while the ELAPSED DAYS and the DETERIORATION DETERMINATION work as designed. To correct this issue, the control logic of the PCM has been changed.
03-003-18-35192018-10-09. Service bulletin. EQUIPMENT; POWER TRAIN; ENGINE. Some vehicles may exhibit an oil leak from the companion flange area (A) of the transfer unit. This concern may be caused by companion flange oil seal wear. The oil seal has been improved to increase the wear resistance.
03-002-18-3505a2018-10-09. Service bulletin. POWER TRAIN:DRIVELINE:DRIVESHAFT; POWER TRAIN:DRIVELINE:UNIVERSAL JOINT. Some vehicles may exhibit a squeak noise from the right front driveshaft at the transaxle when driving. This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. The noise is caused by stick/slip between the oil seal at the transaxle and the dust cover of the drive shaft. To correct this issue, the thickness of the dust cover has been increased.
SA-037-182018-09-10. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration.
03-002-18-35052018-09-10. Service bulletin. POWER TRAIN:DRIVELINE:DRIVESHAFT. Some vehicles may exhibit a squeak noise from the right front driveshaft at the transaxle when driving. This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. The noise is caused by stick/slip between the oil seal at the transaxle and the dust cover of the driveshaft. To correct this issue, the thickness of the dust cover has been increased.
01-014-18-34872018-08-20. Service bulletin. POWER TRAIN. Some customer using "Flexible" setting for Oil Change in the maintenance monitor may notice that the oil change due notification will not work due to improper control logic of the PCM. The PCM clears the TRAVELED DISTANCE at the wrong time while the ELAPSED DAYS and the DETERIORATION DETERMINATION work as designed. To correct this issue, the control logic of the PCM has been changed. This TSB is applicable for the following cases. The oil change due notification does not come on, even after mileage exceeded 10,000 miles. Oil life in the center display is still less than 40% even though the mileage exceeded 7,000 miles. To display "Flexible" setting and "Oil life" on the center screen, select the "Applications" screen, "Maintenance", then "Oil Change" tab. For complete details, refer to the the instructions on MGSS (MAINTENANCE MONITOR OPERATION PROCEDURE).
05-002-18-34542018-05-14. Service bulletin. POWER TRAIN. The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use"ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
05-002-17-33552017-10-21. Service bulletin. POWER TRAIN. Some vehicles may exhibit one of the following concerns: Sometimes the shifter may jump out of 3rd gear over a road bump when accelerating after deceleration at 25-40 mph (40-65 km/h) Hard to shift into 3rd, 4th, 5th, and/or 6th gear Shift lever vibrates when driving in 3rd or 4th gear. This is caused by inappropriate transmission internal parts.
MT-014-172017-08-10. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:SOFTWARE. Whenever you are reprogramming a PCM or any other module, always use the GR8 Battery Charger in the Power Supply mode to prevent the battery from discharging.
05-002-15-3019F2017-06-08. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780, P1738). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION • P1738:00 AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. NOTE: IF THE VEHICLE ALSO HAS A DELAYED ENGAGEMENT CONCERN, THIS TSB IS NOT APPLICABLE. REFER TO MS3 ONLINE INSTRUCTIONS OR WORKSHOP MANUAL FOR PROPER DIAGNOSIS AND REPAIR PROCEDURE.
05-001-15-31042017-06-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL). SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS: • SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) • HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR • SHIFT LEVER VIBRATES WHEN DRIVING IN 3RD OR 4TH GEAR THIS IS CAUSED BY INAPPROPRIATE TRANSMISSION INTERNAL PARTS.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.